Thermal conductivity characteristics of dewatered sewage sludge by thermal hydrolysis reaction

The purpose of this study is to quantify the thermal conductivity of sewage sludge related to reaction temperature for the optimal design of a thermal hydrolysis reactor. We continuously quantified the thermal conductivity of dewatered sludge related to the reaction temperature. As the reaction temperature increased, the dewatered sludge is thermally liquefied under high temperature and pressure by the thermal hydrolysis reaction. Therefore, the bound water in the sludge cells comes out as free water, which changes the dewatered sludge from a solid phase to slurry in a liquid phase. As a result, the thermal conductivity of the sludge was more than 2.64 times lower than that of the water at 20℃. However, above 200℃, it became 0.704 W/m?°C, which is about 4% higher than that of water. As a result, the change in physical properties due to thermal hydrolysis appears to be an important factor for heat transfer efficiency.

ImplicationsThe thermal conductivity of dewatered sludge is an important factor the optimal design of a thermal hydrolysis reactor. The dewatered sludge is thermally liquefied under high temperature and pressure by the thermal hydrolysis reaction. The liquid phase slurry has a higher thermal conductivity than pure water.     

Nitrate-contaminated groundwater remediation by combined autotrophic and heterotrophic denitrification for sulfate and pH control: batch tests

Groundwater remediation was evaluated for combined autotrophic and heterotrophic denitrification under high (154 mg/L as CaCO₃) and low (95 mg/L as CaCO₃) alkaline conditions. Two levels of acetate (47 and 94 mg/L) and ethanol (24 and 48 mg/L) were added to the reactors. Obtained denitrification rates were 2.89, 2.58, 3.55, 1.96, and 2.0 mg-N/L?·?h for high alkaline conditions, whereas under low alkaline conditions has given 2.36, 1.94, 2.47, 2.74, and 2.29 mg-N/L?·?h for control, 47 and 94 mg/L acetate, and 24 and 48 mg/L ethanol, respectively. Nitrite was accumulated for controls but reactors with acetate and ethanol did not accumulate nitrite. Acetate and ethanol addition decreased sulfate to nitrate ratios in the range of 4.5–7.58 for high alkaline conditions (12.77 for control) and 4.43–6.78 for low alkaline conditions (7.90 for control). Acetate was more efficient compared with ethanol in controlling sulfate production and pH maintenance.     

Effect of in vitro administered 2,3,7,8-tetrachlorodibenzo-p-dioxin (TCDD) on DNA-binding activities of nuclear transcription factors in NIH-3T3 mouse fibroblasts

Abstract

Most modern pesticides are expensive. Application of excessive dosage rates is likely to cause undesirable biological side‐effects and is economically wasteful. Non‐uniform distribution of the spray cloud, or application at the wrong time, may result in failure to control the pest. It is the responsibility of the field operator to acquire sufficient knowledge and skill to ensure proper use of the control agents, to increase efficiency of their usage and to reduce unwanted side‐effects. To achieve this goal, he must take into consideration the various physical factors that govern field performance of pesticides.

A simple relationship exists between the spray volume and emission rate used, and droplet size produced. The use of extremely low spray volumes (i.e., those less than 2.0 litre per ha) for forest insect control in Canada, as opposed to higher volumes used in agriculture, necessitates the release of fine droplets (ranging from 20 to 70 μm in diameter) to obtain adequate coverage of the target area. These droplets take a long time to sediment downwards, evaporate in‐flight, become smaller in size and/or form powdery residues, thus contributing to off‐target drift and impaired droplet adhesion to target surfaces. Physical factors such as rain washing, degradation by sunlight and erosion by wind also influence the longevity of pesticide deposits on foliage which is crucial during the critical period of pest control.

Factors affecting the mode of entry into insects are related to the type of ingredients used in formulation. If a pesticide acts via crawling contact, formulations which would provide surface deposits would be more beneficial than emulsions or oil‐based mixes which tend to undergo penetration into foliar cuticle. Physical factors that affect field performance of a pesticide tank mix are related to phase separation and ‘breakdown of emulsions’ in the application equipment; ‘agglomeration and caking’ of wettable powder dispersions at the bottom of the tank; impaired flow behaviour of highly viscous formulations; and coarse atomization of high‐viscosity tank mixes leading to poor target cover.     

Ecological risk assessment of arsenic and metals in sediments of coastal areas of northern Bohai and Yellow Seas, China

Distributions of arsenic and metals in surface sediments collected from the coastal and estuarine areas of the northern Bohai and Yellow Seas, China, were investigated. An ecological risk assessment of arsenic and metals in the sediments was evaluated by three approaches: the Sediment Quality Guidelines (SQGs) of the United States Environmental Protection Agency (USEPA), the degree of contamination, and two sets of SQGs indices. Sediments from the estuaries of the Wuli and Yalu Rivers contained some of the greatest concentrations of arsenic, cadmium, copper, mercury, lead, and zinc. Median concentrations of cadmium and mean concentrations of lead and zinc were greater than background concentrations determined for the areas. All sediments were considered to be heavily polluted by arsenic, but moderately polluted by chromium, lead, and cadmium. Current concentrations of arsenic and metals are unlikely to be acutely toxic, but chronic exposures would be expected to cause adverse effects on benthic invertebrates at 31.4% of the sites.     

Emission Factors for High-Emitting Vehicles Based on On-Road Measurements of Individual Vehicle Exhaust with a Mobile Measurement Platform

ABSTRACT

Fuel-based emission factors for 143 light-duty gasoline vehicles (LDGVs) and 93 heavy-duty diesel trucks (HDDTs) were measured in Wilmington, CA using a zero-emission mobile measurement platform (MMP). The frequency distributions of emission factors of carbon monoxide (CO), nitrogen oxides (NO_x), and particle mass with aerodynamic diameter below 2.5 μm (PM_2.5) varied widely, whereas the average of the individual vehicle emission factors were comparable to those reported in previous tunnel and remote sensing studies as well as the predictions by Emission Factors (EMFAC) 2007 mobile source emission model for Los Angeles County. Variation in emissions due to different driving modes (idle, low- and high-speed acceleration, low- and high-speed cruise) was found to be relatively small in comparison to intervehicle variability and did not appear to interfere with the identification of high emitters, defined as the vehicles whose emissions were more than 5 times the fleet-average values. Using this definition, approximately 5% of the LDGVs and HDDTs measured were high emitters. Among the 143 LDGVs, the average emission factors of NO_x, black carbon (BC), PM_2.5, and ultrafine particle (UFP) would be reduced by 34%, 39%, 44%, and 31%, respectively, by removing the highest 5% of emitting vehicles, whereas CO emission factor would be reduced by 50%. The emission distributions of the 93 HDDTs measured were even more skewed: approximately half of the NO_x and CO fleet-average emission factors and more than 60% of PM_2.5, UFP, and BC fleet-average emission factors would be reduced by eliminating the highest-emitting 5% HDDTs. Furthermore, high emissions of BC, PM_2.5, and NO_x tended to cluster among the same vehicles.

IMPLICATIONS This study presents the characterization of on-road vehicle emissions in Wilmington, CA, by sampling individual vehicle plumes. Approximately 5% of the vehicles were high emitters, whose emissions were more than 5 times the fleet-average values. These high emitters were responsible for 30% and more than 50% of the average emission factors of LDGVs and HDDVs, respectively. It is likely that as the overall fleet becomes cleaner due to more stringent regulations, a small fraction of the fleet may contribute a growing and disproportionate share of the overall emissions. Therefore, long-term changes in on-road emissions need to be monitored.     

Biomineralization-based conversion of carbon dioxide to calcium carbonate using recombinant carbonic anhydrase

Recently, as a mimic of the natural biomineralization process, the use of carbonic anhydrase (CA), which is an enzyme catalyzing fast reversible hydration of carbon dioxide to bicarbonate, has been suggested for biological conversion of CO₂ to valuable chemicals. While purified bovine CA (BCA) has been used in previous studies, its practical utilization in CO₂ conversion has been limited due to the expense of BCA preparation. In the present work, we investigated conversion of CO₂ into calcium carbonate as a target carbonate mineral by using a more economical, recombinant CA. To our knowledge, this is the first report of the usage of recombinant CA for biological CO₂ conversion. Recombinant α-type CA originating in Neisseria gonorrhoeae (NCA) was highly expressed as a soluble form in Escherichia coli. We found that purified recombinant NCA which showed comparable CO₂ hydration activity to commercial BCA significantly promoted formation of solid CaCO₃ through the acceleration of CO₂ hydration rate, which is naturally slow. In addition, the rate of calcite crystal formation was also accelerated using recombinant NCA. Moreover, non-purified crude recombinant NCA also showed relatively significant ability. Therefore, recombinant CA could be an effective, economical biocatalyst in practical CO₂ conversion system.     

Evaluation of the antifungal effects of bio-oil prepared with lignocellulosic biomass using fast pyrolysis technology

This study was performed to investigate the utility of bio-oil, produced via a fast pyrolysis process, as an antifungal agent against wood-rot fungi. Bio-oil solutions (25-100 wt.%) were prepared by diluting the bio-oil with EtOH. Wood block samples (yellow poplar and pitch pine) were treated with diluted bio-oil solutions and then subjected to a leaching process under hot water (70 °C) for 72 h. After the wood block samples were thoroughly dried, they were subjected to a soil block test using Tyromyces palustris and Trametes versicolor. The antifungal effect of the 75% and 100% bio-oil solutions was the highest for both wood blocks. Scanning electron microscopy analysis indicated that some chemical components in the bio-oil solution could agglomerate together to form clusters in the inner part of the wood during the drying process, which could act as a wood preservative against fungal growth. According to GC/MS analysis, the components of the agglomerate were mainly phenolic compounds derived from lignin polymers.     

Removal of heavy metals using waste eggshell

The removal capacity of toxic heavy metals by the reused eggshell was studied.As a pretreatment process for the preparation of reused material from waste eggshell,calcination was performed in the furnace at 800℃for 2 h after crushing the dried waste eggshell.Calcination behavior,qualitative and quantitative elemental information,mineral type and surface characteristics before and after calcination of eggshell were examined by thermal gravimetric analysis(TGA),X-ray fluorescence (XRF),X-ray diffraction(XRD) and scanning electron microscopy(SEM),respectively.After calcination,the major inorganic composition was identified as Ca(lime, 99.63%)and K,P and Sr were identified as minor components.When calcined eggshell was applied in the treatment of synthetic wastewater containing heavy metals,a complete removal of Cd as well as above 99% removal of Cr was observed after 10 min. Although the natural eggshell had some removal capacity of Cd and Cr,a complete removal was not accomplished even after 60 min due to quite slower removal rate.However,in contrast to Cd and Cr,an efficient removal of Pb was observed with the natural eggshell rather than the calcined eggshell.From the application of the calcined eggshell in the treatment of real electroplating wastewater, the calcined eggshell showed a promising removal capacity of heavy metal ions as well as had a good neutralization capacity in the treatment of strong acidic wastewater.     

Production of hydrogen-rich gas from methane by thermal plasma reform

This study investigated the reforming characteristics and optimum operating condition of the high-temperature plasma torch (so called plasmatron) for hydrogen-rich gas (syngas) production. At the optimum condition, the composition of produced syngas was 45.4% hydrogen (H2), 6.9% carbon monoxide (CO), 1.5% carbon dioxide (CO2), and 1.1% acetylene (C2H2). The H2/CO ratio was 6.6, hydrogen yield was 78.8%, and the energy conversion rate was 63.6%. To obtain the optimum operating condition, parametric studies were carried out examining the effects of O2/CH4 ratio, steam/CH4 ratio, and Ni catalyst addition in reactor. When the steam/CH4 ratio was 1.23, the production of hydrogen was maximized and the methane conversion rate was 99.7%. The syngas composition was determined to be 50.4% H2, 5.7% CO, 13.8% CO2, and 1.1% C2H2. The H2/CO ratio was 9.7, hydrogen yield was 93.7%, and the energy conversion rate was 78.8%. Hydrogen production with catalyst was effective, compared with no catalyst.