电炉炼锡废渣制备白炭黑

以电炉炼锡废渣为原料,经过酸浸处理去除Fe元素后,再用沉淀法制备白炭黑。探索了制备白炭黑的最佳工艺条件。分别采用XRD、FTIR、SEM及粒度分析等技术表征了白炭黑产品的物相、形貌、粒径及其分布。实验结果表明,制备白炭黑的最佳工艺条件为:Na OH溶液浓度8 mol/L、固液比1∶10(干燥废渣质量与Na OH溶液体积比,g/m L)、搅拌速率300 r/min、反应温度90℃、反应时间6 h。在最佳工艺条件下制备的白炭黑产品中Si O2质量分数达92.8%。表征结果显示,所制备的白炭黑产品是由近似球形的颗粒聚集而成的无定形非晶体水合二氧化硅,粒径为95~200 nm的颗粒约占87.5%。     

利用给水厂污泥制备透水砖的实验研究

以给水厂污泥、粉煤灰和普通砂为主要原料,添加一定量的粘结剂制备透水砖。探讨了污泥掺加量、烧结温度和成型压力对透水砖基本性能的影响,结果表明,当污泥掺量为30%～40%,添加30%～35%,粒径为1.0～1.4 mm普通砂颗粒时,在30 MP压力下成型、1 150℃下烧结制备出的成品抗压强度达36.53 MP,透水系数为1.08×10-2cm/s,满足JC/T945-2005《透水砖》相关要求。     

葛洲坝下游近坝区水域鱼类资源声学调查与评估

于2013年4月及6月,针对DIDSON的特点设计了携带声呐的船舶走航式及定点式两种方法,对葛洲坝下游近坝区水域（大江、三江至下游镇江阁处江段）进行水声学调查,观察鱼类资源的时空分布特点。观测数据经去噪处理,获得鱼类资源结果。结果表明：葛洲坝下游近坝区鱼类资源分布呈明显的空间差异,大江水域鱼类密度显著高于三江水域,且近坝区高于下游江段,最大值为6924 ind./1 000 m3,位于大江电站下游约1 km处,最小值为153 ind./1 000 m3,位于宜化大楼江段。鱼类资源在时间上没有显著的统计学差异,6月份鱼类活动昼夜差别比4月份更明显,主要集中在上层水域,傍晚至凌晨鱼类活动较少。进一步分析发现,船闸的运行方式、水体中食物可获取程度、各鱼类种群生活习性差异等,均对鱼类资源时空分布产生影响。此外,开展适逢葛洲坝禁渔期,禁渔措施维持了近坝区水域春、夏季鱼类资源量的稳定性,是保护鱼类资源的有效而直接的方法     

咪唑啉硫酸酯盐的缓蚀性能及协同增效作用研究

参照SY/T 5405-1996《酸化用缓蚀剂性能试验方法及评价指标》,采用静态失重法评价咪唑啉硫酸酯盐缓蚀剂1-羟乙基-2-油酸基咪唑啉硫酸酯盐(ISES)与丙炔醇(BCC)、非离子表面活性剂OP-10组成的二元和三元复配缓蚀剂体系对N80钢的缓蚀性能,考察二元和三元复配缓蚀剂体系的协同增效作用。通过动电位极化扫描和电化学阻抗分析对ISES及其复配体系的电化学行为进行研究。     

Biochars derived from carp residues: characteristics and copper immobilization performance in water environments

● P-rich carp residues-derived biochars presented excellent Cu sorption capacity. ● Sorption mechanisms of Cu on CRBs were mainly precipitation and surface complexation. ● CRBs could immobilize Cu and reduce its bioavailability in aquatic environment. Heavy metal pollution has attracted worldwide attention because of its adverse impact on the aquatic environment and human health. The production of biochar from biowaste has become a promising strategy for managing animal carcasses and remediating heavy metal pollution in the aquatic environment. However, the sorption and remediation performance of carp residue-derived biochar (CRB) in Cu-polluted water is poorly understood. Herein, batches of CRB were prepared from carp residues at 450–650 °C (CRB450–650) to investigate their physicochemical characteristics and performance in the sorption and remediation of Cu-polluted water. Compared with a relatively low-temperature CRB (e.g., CRB450), the high-temperature biochar (CRB650) possessed a large surface area and thermodynamic stability. CRB650 contained higher oxygen-containing functional groups and P-associated minerals, such as hydroxyapatite. As the pyrolytic temperature increased from 450 to 650°C, the maximum sorption capacity of the CRBs increased from 26.5 to 62.5 mg/g. The adsorption process was a type of monolayer adsorption onto homogenous materials, and the sorption of Cu²⁺ on the CRB was mainly based on chemical adsorption. The most effective potential adsorption mechanisms were in order of electrostatic attraction and cation-π interaction > surface complexation and precipitation > pore-filling and cation exchange. Accordingly, the CRBs efficiently immobilized Cu²⁺ and reduced its bioavailability in water. These results provide a promising strategy to remediate heavy metal-polluted water using designer biochars derived from biowastes, particularly animal carcasses.     

环境一号卫星环境应用系统工程及其关键技术研究进展

简介长达11年的国家重点项目“环境一号卫星环境应用系统工程及其关键技术研究”的核心内容及其重要研究成果,对环境一号卫星系统需求分析、设计理论、研制发射和运行应用全过程进行了完整的研究与实践,为环境一号卫星系统的建设、应用和业务运行奠定了重要基础。     

Elemental and individual particle analysis of atmospheric aerosols from high Himalayas

Atmospheric aerosols were collected during the scientific expedition to Mt. Qomolangma (Everest) in May–June, 2005. The elemental concentrations of the aerosols were determined by inductively coupled plasma mass spectrometry. This yielded data for the concentration of 14 elements: Na, Mg, Al, K, Ca, Ti, V, Cr, Mn, Fe, Ni, Cu, Zn, and Pb. The mean elemental concentrations were generally comparable with those from central Asia and the Arctic, while much higher than those from Antarctic. Size, morphology, and chemical composition of 900 individual aerosol particles were determined by scanning electron microscopy and energy-dispersive X-ray microanalysis. Based on morphology and elemental composition, the particles were clustered into eight groups: soot (8%), tar ball (3%), alumosilicates/silica (55%), calcium sulfate (16%), Ca/Mg carbonate (2%), Fe/Ti-rich particles (3%), Pb-rich particles (1%), and biological particles (12%). The sampling site, located at 6,520 m in the Himalayas, is particularly remote and located at high altitude. Nonetheless, high aerosol enrichment factors for copper, chromium, lead, nickel, vanadium, and zinc all suggest the influence of long-range transported pollution, while enrichment in calcium and the presence of alumino-silicates in individual particle analyses indicates a distinct mineral dust influence. The backward air mass trajectories showed that the northwestern part of India may contribute to the atmospheric aerosol in the central high Himalayas.     

煤矿人因组织错误事故致因研究

本文应用编码故障树分析法,从人因组织错误的角度,对煤矿事故致因进行剖析。在综合安全管理学、心理学、组织行为学等学科的基础上,尝试构建煤矿人因组织错误事故模型。     

运用本质安全原理预防煤粉爆炸

旨在将本质安全原理与粉尘爆炸(以煤粉爆炸为例)的风险控制联系起来。利用20 L球形爆炸装置的标准测试方法测试煤粉及煤粉-CaCO3混合物的爆炸下限、最大爆炸压力、压力上升速度等爆炸特性。基于本质安全基本原理和试验结果,讨论预防煤粉爆炸的各种基本方法,并重点阐述本质安全原理与粉尘爆炸影响因素、不同的预防方法、过程设备的选择等之间的关系,对已制定的爆炸风险控制措施进行完善和补充。     

Characterization of alkali-activated thermally treated incinerator bottom ash

The fine fraction (<14mm) of incinerator bottom ash (IBA) obtained from a UK energy from waste plant has been milled and thermally treated at 600, 700, 800 and 880 degrees C. Treated materials have been activated with Ca(OH)(2) (10wt%) and the setting times and compressive strengths at different curing times measured. In addition to decomposition of CaCO(3) to CaO, thermal treatment increases the content of gehlenite (Ca(2)Al(2)SiO(7)), wollastonite (CaSiO(3)) and mayenite (Ca(12)Al(14)O(33)). Thermally treated samples were significantly more reactive than milled IBA and heating to 700 degrees C produced a material which rapidly set. Silica, gehlenite and wollastonite were the main crystalline phases present in hydrated samples and a mixed sulphate-carbonate AFm-type phase (Ca(4)Al(2)O(6)(CO(3))(0.67)(SO(3))(0.33).11H(2)O) formed. Significant volumes of gas were generated during curing and this produced a macro-porous microstructure that limited strength to 2.8MPa. The new materials may have potential for use as controlled low-strength materials.