ABR反应器的启动研究

研究了添加填料对折流式厌氧反应器(ABR)启动性能的影响.反应器启动时,控制COD负荷为0.15 kg/(m3*d),逐渐提升至0.6 kg/(m3*d).未加填料的反应器经过约60 d,加入填料的反应器经过约35 d的连续运行,出水COD去除率稳定,启动基本完成.研究表明,添加填料的复合式反应器启动速度明显快于普通ABR,且运行稳定性更好,COD去除率较高,能够较好地截留污泥,有利于反应器生物效应的形成.     

基于FDS的加油站便利店火灾模拟

为了研究加油站便利店火灾的发展规律,选择合理的疏散路线,使用 FDS软件对某加油站便利店进行火灾数值模拟。通过观察烟气扩散和动态升温过程,分析便利店的烟气扩散和升温规律,对比分析不同疏散路线上温度、烟气层高度和能见度的数据变化规律,分析选择不同疏散路线对人员安全疏散的影响。结果表明:在无火灾报警设备的情况下,卫生间等有隔断的设施会延迟设施内人员获得火灾信息的时间,不利于安全疏散;同等高度下靠墙区域受高温烟气影响较中央开阔区域更大;疏散时选择合理的疏散路线可以显著延长安全疏散时间。     

输气管道小孔泄漏压力响应实验与仿真研究

管道压力是进行泄漏速率和泄漏后果模拟的重要参数,搭建泄漏及气体扩散测试实验系统,并建立实验系统的Flowmaster模型,通过实验数据对模型进行验证,验证结果表明,可以基于Flowmaster模型预测小孔泄漏条件下管道内的压力响应情况,并且能够较为精确的计算泄漏稳定后管内的平均压力,为小孔模型准确计算泄漏速率提供理论依据。     

钛基IrO2-RuO2阳极电解处理亚甲基蓝溶液

采用钛基IrO2-RuO2为阳极材料,不锈钢为阴极材料,NaCl质量浓度为10 g/L的溶液为电解液,对亚甲基蓝溶液进行电化学处理。实验结果表明:处理初始质量浓度为25 mg/L的亚甲基蓝溶液,电解电流0.050 A,电解20 min后亚甲基蓝去除率达95%;处理初始质量浓度为100 mg/L的亚甲基蓝溶液,电解电流0.100 A,电解30 min后亚甲基蓝去除率达98%。随着电解时间和电解电流的增加,亚甲基蓝去除率均增大。     

Molding Method, Thermal and Mechanical Properties of Jute/PLA Injection Molding

Natural composites have been important materials system due to preservation of earth environments. Natural fibers such as jute, hemp, bagasse and so on are very good candidate of natural composites as reinforcements. On the other hand regarding matrix parts thermosetting polymer and thermoplastic polymer deriver form petrochemical products are not environmental friendly material, even if thermoplastic polymer can be recycled. In order to create fully environmental friendly material (FEFM) biodegradable polymer which can be deriver from natural resources is needed. Therefore poly(lactic acid) (PLA) polymer is very good material for the FEFM. In this paper jute fiber filled PLA resin (jute/PLA) composites was fabricated by injection moldings and mechanical properties were measured. It is believable that industries will have much attention to FEFM, so that injection molding was adopted to fabricate the composites. Long fiber pellet fabricated by pultrusion technique was adopted to prepare jute/PLA pellet. Because it is able to fabricate composite pellets with relative long length fibers for injection molding process, where, jute yarns were continuously pulled and coated with PLA resin. Here two kinds of PLA materials were used including the one with mold releasing agent and the other without it. After pass through a heated die whereby PLA resin impregnates into the jute yarns and sufficient cooling, the impregnated jute yarns were cut into pellets. Then jute/PLA pellets were fed into injection machine to make dumbbell shape specimens. In current study, the effects of temperature of PLA melting temperature i.e. impregnation temperature and the kinds of PLA were focused to get optimum molding condition. The volume fractions of jute fiber in pellet were measured by several measuring method including image analyzing, density measurement and dissolution methods. Additionally, thermal and mechanical properties were investigated. It is found that 250° is much suitable for jute/PLA long fiber pultrusion process because of its less heat degradation of jute, better impregnation, acceptable mechanical property and higher production efficiency. Additionally the jute fibers seem much effective to increase deflection temperature under load, tensile modulus and Izod strength.     

污泥热水解技术研究进展

热水解可以改善污泥的生物降解性能和脱水性能,提高后续厌氧消化系统中有机物的去除率。本文阐述了热水解对污泥物理特性主要包括流变特性和脱水行为的影响;分析了热水解对污泥中氨氮浓度及对厌氧消化的作用;同时介绍了热水解技术对整个污泥处理系统能量需求的影响。指出：热水解改善了污泥的厌氧消化性能,提高了沼气等再生资源的产量,且厌氧消化产生的沼气量与热水解技术所需的能量基本平衡。     

Effects of leachate accumulation on landfill stability in humid regions of China

Leachate levels are important to landfill stability and safety. High leachate or water levels often lead to landfill instability, which can cause accidents. Here a case study of a landfill located in a humid region of southern China is presented. Leachate distribution and quality were systematically analyzed, and the effect of leachate level on waste-mass stability was assessed. Boreholes were drilled in the field, samples were analyzed in the laboratory, and a simulation was performed. In addition, the safety and stability of the landfill was evaluated. The leachate level in the landfill was 9–19 m, which was higher than the top of the dam crest (8–20 m). Leachate accounted for more than 1/4 of the total landfill storage capacity. The contaminant concentration of the leachate samples collected directly from the waste body was very high, with large variation among the samples. The mean concentrations of NH₃–N, BOD, and COD from the waste body were 5404, 14,136, and 22,691 mg/L, nearly 2.7, 2.4, and 1.8 times the mean concentrations in the leachate pond, respectively. Three series of shear strength parameters were used in a slope stability analysis, and a limit equilibrium method was used to calculate the factor of safety (Fs). The analysis showed that Fs could be affected by potential anisotropy in the shear strength of the waste. The minimum values of Fs corresponding to series I were 1.84 and 1.17 for units ? and II, respectively. The Fs value of unit II was significantly lower than the safe design value (1.25). In addition, Fs decreased with increase in the normalized height of the leachate level, h/H, where h is the height of the leachate mound and H is the maximum thickness of the landfill. If the h/H values of units I and II are kept below 50% and 40%, respectively, a safe design value of 1.25 for Fs can be guaranteed. Therefore, some measures to prevent risk should be considered.     

污染环境罪司法适用争议问题研究

《刑法修正案（八）》颁布实施后,污染环境罪适用已经一年有余,然而一些争议问题仍未厘清,尤其是主观罪过形态以及严格责任问题,理论界和司法实践中还存在不同的认识。笔者认为,将污染环境罪认定为过失犯罪不存在理论上的不恰切,相反更符合刑法罪责刑相适应的原则。同时严格责任在我国刑法中没有适用的空间。