化学氧化剂对水华蓝藻的控制研究

对比了过氧化氢（H₂O₂）、高铁酸钾（K₂FeO₄）和过碳酸钠（Na₂CO₄）3种氧化剂对自然水体中群体蓝藻生长和光合活性的影响.结果发现,3种氧化剂对蓝藻均有快速的抑制效应,且随着氧化剂浓度的增加抑制效果增强.相同氧化剂浓度下,H₂O₂对水华蓝藻的去除能力强于K₂FeO₄和Na₂CO₄,对蓝藻光合系统Ⅱ的最大光量子产量（F_v/F_m）和有效光量子产量（F_v'/F_m'）的抑制效果也更显著.H₂O₂对不同浓度水华蓝藻的控制实验结果表明,初始藻细胞浓度对H₂O₂控藻效果影响较大,细胞密度越大,H₂O₂降解率增加,抑藻效果急剧下降.当初始藻密度为10μg/L和100μg/L,5mg/L H₂O₂的48h降解率分别为64.9%和97.5%,对藻细胞F_v/F_m的抑制率分别为10%和1%.因此,实施H₂O₂控制蓝藻水华的措施应该尽量在蓝藻水华形成早期,即藻密度较低的时候使用.     

Prevalence and Bayesian Phylogenetics of Enteroviruses Derived From Environmental Surveillance Around Polio Vaccine Switch Period in Shandong Province,China

Food and Environmental Virology - We present the results of environmental surveillance for poliovirus (PV) and non-poliovirus (NPEV) around the switch from trivalent to bivalent oral polio-vaccine...     

合肥市典型交通干道大气苯系物的特征分析

为研究合肥市交通干道大气苯系物污染状况,采用自主研制的差分吸收光谱(DOAS)系统,于2016年3月期间对合肥市交通主干道大气苯系物(苯、甲苯、间二甲苯和邻二甲苯)以及常规污染物NO_2、SO_2等进行了连续观测.观测结果显示,观测期间苯、甲苯、间二甲苯和邻二甲苯的平均浓度分别为:21.7、63.6、33.9和98.7μg·m~(-3).与国内外其它城市比较显示,合肥市交通干道大气苯和甲苯的污染处于中等水平,二甲苯的污染较为严重.结合观测期的间风速风向、T/B特征比值以及与CO等污染物的相关性,对上述苯系物来源进行了分析,结果显示观测期间T/B值为0.8~4.5,苯、甲苯与CO的相关性系数R分别为0.55和0.34.表明机动车尾气排放是观测区域苯和甲苯的主要排放源之一,同时也受到周边工业园区排放的影响,二甲苯的主要排放源为观测地点北偏东方向的涂料行业工业园区.苯和甲苯的夜间高浓度峰值分析结果表明,夜间的高浓度苯和甲苯可能主要来源于观测地点周边工业园区的排放.观测区域苯系物的臭氧生成潜势(OFP)表现为邻二甲苯间二甲苯甲苯苯,其中二甲苯的OFP占总OFP的85%,表明周边工业园区的排放对该地区臭氧生成的贡献较大.     

黄河干流宁蒙段溶解性有机物组分特征及其与金属离子的相关性

溶解性有机物(dissolved organic matter,DOM)是天然水体的重要组成部分,由于化学极性及所含的官能团不同,其在水体中的化学行为也不同.本研究以黄河干流宁蒙段为研究对象,于2015年4月采集了下河沿至头道拐沿程7个断面的水样,采用XAD系列树脂将DOM分为疏水性酸(hydrophobic acid,HOA)、疏水性碱(hydrophobic base,HOB)、弱疏水性酸(weak hydrophobic acid,WHOA)和亲水性物质(hydrophilic matter,HYI)这4个组分,探讨了DOM组分含量、荧光峰值及其与Pb、Zn、Cu、Cr、As这5种金属离子之间的相关性.结果表明,黄河宁蒙段DOM总量由下河沿至头道拐沿程逐渐增加.各断面DOM腐殖化程度较低,以亲水性的蛋白质类小分子物质(HYI)为主,疏水性酸(HOA)次之,这与黄河沿岸排污导致内源作用增强有关.三维荧光光谱中类腐殖质和类蛋白质荧光峰型显著,且类腐殖质峰沿程逐渐增强,进一步证实了内源污水输入的影响.SPSS相关性分析结果表明,DOM与5种金属离子呈现出不同程度的相关性,其中与Cu离子显著相关;4种组分中HYI与Cu离子的相关性最强,说明二者在迁移转化过程中存在显著相互作用.进一步研究发现,芳香蛋白类物质荧光峰强度随Cu离子浓度的升高而降低,这可能是Cu与亲水性组分中的芳香类蛋白质发生络合产生荧光淬灭效应,从而导致荧光强度降低.     

污泥超高温堆肥过程中DOM结构的光谱分析

为了明确超高温堆肥新工艺在促进腐殖化进程中的优势,采用三维荧光光谱(3D-EEM)等光谱学方法研究了污泥超高温堆肥过程中DOM的结构特征及其变化规律.结果表明,堆体≥80℃的超高温阶段持续5 d(最高温度90℃),50℃以上高温阶段达到22 d,反映了堆肥过程中强烈的微生物代谢活性.E253/E203、SUVA280、S275~295等9个紫外-可见光光谱(UV-Vis)指标在0~23 d变化显著,指出DOM的芳香化和堆肥腐殖化程度逐渐增强.3D-EEM光谱结合荧光区域体积积分技术(FRI)分析指出,DOM中蛋白类物质在超高温堆肥过程的0~6 d几乎完全被降解;腐殖酸和富里酸类物质在0~23 d大量形成,堆肥在高温阶段达到完全腐熟,这与种子发芽指数(GI)在23 d所指示的腐熟度评价结果(98.5%)一致.基于多种光谱学指标的相关性分析,PⅤ,n/PⅢ,n与其它光谱学均呈现较好的相关性(r≥0.68),可以作为评价超高温堆肥腐熟度的光谱学指标.上述结果证实了超高温堆肥工艺可加快堆肥腐熟进程、缩短堆肥周期至20 d左右,在有机固废资源化领域具有极大的应用潜力.     

海域高温油田1株耐高温耐盐硫酸盐还原菌的筛选与生理特性及活性抑制

油田中硫酸盐还原菌(SRP)的生长代谢能产生大量H_2S,会引起油藏酸化和微生物腐蚀等严重的生产和环境问题,而关于油田环境中SRP微生物多样性与生理活性的研究仍十分缺乏.为了深入了解我国渤海湾海域高温酸化油藏中SRP代谢特点并探究其潜在危害控制方法,本研究采用厌氧纯培养技术从渤海湾某高温油田采出水中分离筛选到1株耐高温、耐盐的SRP菌株BQ1,研究了其生理特性,并评价了不同杀菌剂和代谢抑制剂对其产H_2S活性的影响.结果表明,菌株BQ1的细胞呈短杆状,大小为(1.2~2.5)μm×(0.5~0.8)μm,有运动性.尽管BQ1与普通脱硫弧菌(Desulfovibrio vulgaris Hildenborough)的16S rRNA基因序列相似性达99%,但两者生理特性具有明显差异.BQ1可在温度为14~70℃(最适30℃)、p H 6.0~9.0(最适7.0)、盐度为0%~10%条件下生长代谢.BQ1可利用甲酸钠、乳酸钠、乙酸盐等多种碳源,能以硫酸盐、亚硫酸盐、硫代硫酸盐或单质硫为唯一电子受体产生H_2S.次氯酸钠(600 mg·L~(-1))、苄基三甲基氯化铵(300 mg·L~(-1))或NaNO_3(800 mg·L~(-1))对BQ1产H_2S活性无明显抑制效果.戊二醛(50 mg·L~(-1))、溴硝醇(30 mg·L~(-1))、二氧化氯(50 mg·L~(-1))或NaNO_2(70 mg·L~(-1))可抑制BQ1产H_2S活性达30 d以上,是控制渤海湾高温油田微生物酸化的潜在有效抑制剂.     

钙法解吸并固定乙醇胺富液中CO2

针对醇胺类吸收剂富液中CO_2的解吸及后续处置所存在的不足,提出一种新型解吸方案——钙法.通过CO_2负荷试验和Ca(OH)_2投加量试验确定了该法理想处理负荷为0.84 mol·L-1,理想投加比例为C∶Ca=1∶1(摩尔比),此条件下反应15 min和30 min的解吸率达到52.17%和55.02%,这表明钙法矿化解吸乙醇胺富液中CO_2是可行的.在此基础上,进一步研究了pH、温度和搅拌强度对CO_2解吸固定效果的影响.试验结果表明,CO_2解吸率随着pH和搅拌强度的增加而增大,但当pH和搅拌强度增大到一定程度后,解吸率增长放缓甚至出现下降.较高的解吸温度尽管解吸率更大,但高温条件下无法达到矿化固定CO_2的目的.CO_2二次吸收负荷试验表明经钙法解吸后的MEA再生液具有良好的可重复使用性.     

Performance and fouling mechanism of direct contact membrane distillation (DCMD) treating fermentation wastewater with high organic concentrations

In this study,direct contact membrane distillation(DCMD)was used for treating fermentation wastewater with high organic concentrations.DCMD performance characteristics including permeate flux,permeate water quality as well as membrane fouling were investigated systematically.Experimental results showed that,after 12 hr DCMD,the feed wastewater was concentrated by about a factor of 3.7 on a volumetric basis,with the permeate flux decreasing from the initial 8.7 L/m~2/hr to the final 4.3 L/m~2/hr due to membrane fouling;the protein concentration in the feed wastewater was increased by about 3.5 times and achieved a value of 6178 mg/L,which is suitable for reutilization.Although COD and TOC in permeate water increased continuously due to the transfer of volatile components from wastewater,organic rejection of over 95%was achieved in wastewater.GC–MS results suggested that the fermentation wastewater contained 128kinds of organics,in which 14 organics dominated.After 12 hr DCMD,not only volatile organics including trimethyl pyrazine,2-acetyl pyrrole,phenethyl alcohol and phenylacetic acid,but also non-volatile dibutyl phthalate was detected in permeate water due to membrane wetting.FT-IR and SEM–EDS results indicated that the deposits formed on the membrane inner surface mainly consisted of Ca,Mg,and amine,carboxylic acid and aromatic groups.The fouled membrane could be recovered,as most of the deposits could be removed using a HCl/Na OH chemical cleaning method.     

Are current Chinese national ambient air quality standards on 24-hour averages for particulate matter sufficient to protect public health?

With rapid economic development and urbanization in recent decades, China has experienced the worsening of ambient air quality. For better air quality management to protect human health, Chinese government revised national ambient air quality standards(NAAQS) for particulate matter(PM) in 2012(GB3095-2012). To assess the effectiveness of current NAAQS for PM on public health in Chinese population, we conducted a metaanalysis on published studies examining the mortality risk of short-term exposure to PM with aerodynamic diameters less than 10 and 2.5 μm(PM_(10) and PM_(2.5)) in China. The reported24-hour concentrations of PM_(10) and PM_(2.5) in studies ranged from 43.5 to 150.1 μg/m~3 and 37.5 to 176.7 μg/m~3. In the pooled excess, mortality risk estimates of short-term exposure to PM.In specific, per 10 μg/m~3 increase in PM_(10), we observed increases of 0.40%(95%CI: 0.33%,0.47%), 0.57%(95%CI: 0.44%, 0.70%) and 0.49%(95%CI: 0.40%, 0.58%) in total, respiratory and cardiovascular mortality, per 10 μg/m~3 increase in PM_(2.5), we observed increases of 0.51%(95%CI: 0.38%, 0.63%), 0.62%(95%CI: 0.52%, 0.73%) and 0.75%(95%CI: 0.54%, 0.95%) in total,respiratory and cardiovascular mortality. Finally, we derived 125 μg/m~3 for PM_(10) and 62.5 μg/m~3 for PM_(2.5) as 24-hour recommendation values based on the pooled estimates. Our results indicated that current Chinese NAAQS for PM could be sufficient in mitigating the excess mortality risk from short-term exposure to ambient PM. However, future research on longterm exposure cohort studies in Chinese population is also essential in revising annual averages for PM in Chinese NAAQS.     

Behaviors and kinetics of toluene adsorption‐desorption on activated carbons with varying pore structure

This work was undertaken to investigate the behaviors and kinetics of toluene adsorption and desorption on activated carbons with varying pore structure. Five kinds of activated carbon from different raw materials were selected. Adsorption isotherms and breakthrough curves for toluene were measured. Langmuir and Freundlich equations were fitted to the equilibrium data, and the Freundlich equation was more suitable for simulating toluene adsorption. The process consisted of monolayer, multilayer and partial active site adsorption types. The effect of the pore structure of the activated carbons on toluene adsorption capacity was investigated. The quasi-first-order model was more suitable for describing the process than the quasi-second-order model. The adsorption data was also modeled by the internal particle diffusion model and it was found that the adsorption process could be divided into three stages. In the external surface adsorption process, the rate depended on the specific surface area. During the particle diffusion stage, pore structure and volume were the main factors affecting adsorption rate. In the final equilibrium stage, the rate was determined by the ratio of meso-and macro-pores to total pore volume. The rate over the whole adsorption process was dominated by the toluene concentration. The desorption behavior of toluene on activated carbons was investigated,and the process was divided into heat and mass transfer parts corresponding to emission and diffusion mechanisms, respectively. Physical adsorption played the main role during the adsorption process.