Life cycle assessment of selective non-catalytic reduction (SNCR) of nitrous oxides in a full-scale municipal solid waste incinerator

Selective non-catalytic reduction (SNCR) of nitrous oxides in a full-scale municipal solid waste incinerator was investigated using LCA. The relationship between NO_x-cleaning and ammonia dosage was measured at the plant. Un-reacted ammonia - the ammonia slip - leaving the flue-gas cleaning system adsorbed to fly-ash or in the effluent of the acidic scrubber was quantified from the stoichiometric reaction of NO_x and ammonia assuming no other reaction products was formed. Of the ammonia slip, 37% was associated with the fly-ash and 63% was in the effluent of the acidic scrubber. Based on NO_x-cleaning efficiency, the fate of the ammonia slip as well as the environmental impact from ammonia production, the potential acidification and nutrient enrichment from NO_x-cleaning was calculated as a function of ammonia dosage. Since the exact fate of the ammonia slip could not be measured directly, a number of scenarios were set up ranging from “best case” with no ammonia from the slip ending up in the environment to “worst case” where all the ammonia slip eventually ended up in the environment and contributed to environmental pollution. In the “best case” scenario the highest ammonia dosage was most beneficial demonstrating that the environmental load associated with ammonia production is of minor importance. In contrast, in a “worst case” scenario” NO_x-cleaning using SNCR is not recommendable at all, since the impacts from the ammonia slip exceed the saved impacts from the NO_x removal. Increased dosage of ammonia for removal of NO_x is recommendable as long as less than 10-20% of the ammonia slip to the effluent of the acidic scrubber ends up in the environment and less than 40% of the slip to the fly-ash ends up in the environment. The study suggests that the actual fate of the ammonia slip is crucial, but since the release of the ammonia may take place during transport and at the facilities that treat the wastewater and treat the fly-ash this factor depends strongly on local conditions and may be hard to determine. Thus, LCA-modeling proved useful in assessing the balance between ammonia dosage and NO_x-removal in flue-gas cleaning from waste incineration.     

Improving the layout of recycling centres by use of lean production principles

There has been increased focus on recycling in Sweden during recent years. This focus can be attributed to external environmental factors such as tougher legislation, but also to the potential gains for raw materials suppliers. Recycling centres are important components in the Swedish total recycling system. Recycling centres are manned facilities for waste collection where visitors can bring, sort and discard worn products as well as large-sized, hazardous, and electrical waste. The aim of this paper was to identify and describe the main flows and layout types at Swedish recycling centres. The aim was also to adapt and apply production theory for designing and managing recycling centre operations. More specifically, this means using lean production principles to help develop guidelines for recycling centre design and efficient control.Empirical data for this research was primarily collected through interviews and questionnaires among both visitors and employees at 16 Swedish recycling centres. Furthermore, adapted observation protocols have been used in order to explore visitor activities. There was also close collaboration with a local recycling centre company, which shared their layout experiences with the researchers in this project.The recycling centres studied had a variety of problems such as queues of visitors, overloading of material and improper sorting. The study shows that in order to decrease the problems, the recycling centres should be designed and managed according to lean production principles, i.e. through choosing more suitable layout choices with visible and linear flows, providing better visitor information, and providing suitable technical equipment. Improvements can be achieved through proper planning of the layout and control of the flow of vehicles, with the result of increased efficiency and capacity, shorter visits, and cleaner waste fractions. The benefits of a lean production mindset include increased visitor capacity, waste flexibility, improved sorting quality, shorter time for visits and improved working conditions.     

Material and energy recovery in integrated waste management systems. An evaluation based on life cycle assessment

This paper reports the environmental results, integrated with those arising from mass and energy balances, of a research project on the comparative analysis of strategies for material and energy recovery from waste, funded by the Italian Ministry of Education, University and Research. The project, involving the cooperation of five University research groups, was devoted to the optimisation of material and energy recovery activities within integrated municipal solid waste (MSW) management systems. Four scenarios of separate collection (overall value of 35%, 50% without the collection of food waste, 50% including the collection of food waste, 65%) were defined for the implementation of energetic, environmental and economic balances. Two sizes of integrated MSW management system (IWMS) were considered: a metropolitan area, with a gross MSW production of 750,000 t/year and an average province, with a gross MSW production of 150,000 t/year. The environmental analysis was conducted using Life Cycle Assessment methodology (LCA), for both material and energy recovery activities. In order to avoid allocation we have used the technique of the expansion of the system boundaries. This means taking into consideration the impact on the environment related to the waste management activities in comparison with the avoided impacts related to the saving of raw materials and primary energy. Under the hypotheses of the study, both for the large and for the small IWMS, the energetic and environmental benefits are higher than the energetic and environmental impacts for all the scenarios analysed in terms of all the indicators considered: the scenario with 50% separate collection in a drop-off scheme excluding food waste shows the most promising perspectives, mainly arising from the highest collection (and recycling) of all the packaging materials, which is the activity giving the biggest energetic and environmental benefits. Main conclusions of the study in the general field of the assessment of the environmental performance of any integrated waste management scheme address the importance of properly defining, beyond the design value assumed for the separate collection as a whole, also the yields of each material recovered; particular significance is finally related to the amount of residues deriving from material recovery activities, resulting on average in the order of 20% of the collected materials.     

White clover clones as a cost-effective indicator of phytotoxic ozone: 10 years of experience from central Italy

Data collected at one site in central Italy using the NC-S/NC-R clover (Trifolium repens) biotype system during 1997-2007 were analysed in order to assess: (a) its performance under Mediterranean conditions; (b) variations of ozone damage linked with meteorological conditions; (c) if critical level approach is a good predictor of ozone risk on vegetation. NC-S dry biomasses were systematically lower than those of NC-R, the mean ratio being 0.7. Relevant relationship between ozone visible injury and cumulated values of AOT40 were also reported. Temperature and number of rainy days were the most important factors associated with ozone presence and, as a consequence, with leaf injury index. Photosynthetic gas exchange properties indicate that NC-S has higher values of stomatal conductance.     

EU-wide survey of polar organic persistent pollutants in European river waters

This study provides the first EU-wide reconnaissance of the occurrence of polar organic persistent pollutants in European river waters. More than 100 individual water samples from over 100 European rivers from 27 European Countries were analysed for 35 selected compounds, comprising pharmaceuticals, pesticides, PFOS, PFOA, benzotriazoles, hormones, and endocrine disrupters. Around 40 laboratories participated in this sampling exercise. The most frequently and at the highest concentration levels detected compounds were benzotriazole, caffeine, carbamazepine, tolyltriazole, and nonylphenoxy acetic acid (NPE₁C). Only about 10% of the river water samples analysed could be classified as “very clean” in terms of chemical pollution. The rivers responsible for the major aqueous emissions of PFOS and PFOA from the European Continent could be identified. For the target compounds chosen, we are proposing “indicative warning levels” in surface waters, which are (for most compounds) close to the 90th percentile of all water samples analysed.     

A decision framework for possible remediation of contaminated sediments in the River Kymijoki, Finland

Background, aim, and scope  The paper describes the spatial contamination of the River Kymijoki, South-Eastern Finland, and the coastal region of the Gulf of Finland with PCDD/Fs and mercury. The findings of ecotoxicologial and human health studies are also reported, including environmental and human risk assessments. Sediments from the River Kymijoki, draining into the Gulf of Finland, have been heavily polluted by the pulp and paper industry and by chemical industries. A wood preservative, known as Ky-5, was manufactured in the upper reaches of the river between 1940 and 1984 causing severe pollution of river sediments with polychlorinated dibenzo-p-dioxins (PCDD) and dibenzofurans (PCDF). Moreover, the sediments have been polluted with mercury (Hg) from chlor-alkali production and the use of Hg as a slimicide in pulp and paper manufacturing. Materials and methods  An extensive sediment survey was conducted as well as sediment transport modeling, toxicity screening of sediment invertebrates, and a survey of contaminant bioaccumulation in invertebrates and fish. Studies on human exposure to PCDD/Fs and the possible effects on hypermineralization of teeth as well as an epidemiological study to reveal increased cancer risk were also conducted. An assessment of the ecological and human health risks with a null hypothesis (no remediation) was undertaken. Results  The sediment survey revealed severe contamination of river and coastal sediments with PCDD/Fs and Hg. The total volume of contaminated sediments was estimated to reach 5 × 10⁶ m³ and hot spots with extremely high concentrations (max 292,000 ng g⁻¹ or 1,060 ng I-TEQ g⁻¹ d.w.) were located immediately downstream from the pollution source (approximately 90,000 m³). Sediment contamination was accompanied by changes in benthic assemblages, but direct effects were masked by many factors. The fish showed only slightly elevated PCDD/F levels in muscle, but orders of magnitude higher in the liver compared with reference freshwater sites and the Baltic Sea. The concentrations in human fat did not reveal high human exposure in the Kymijoki area in general and was lower than in sea fishermen. The relative risk for total cancer among farmers was marginally higher (RR = 1.13) among those living close to the river, compared with farmers living further away, and the possibility of increased cancer risk cannot be ruled out. A conservative risk assessment revealed that the present probability of exceeding the WHO upper exposure limit of 4 pg WHO-TEQ kg⁻¹ d⁻¹ for PCDD/Fs and DL-PCBs was 6%. The probability of exceeding the WHO limit value of 0.23 μg kg⁻¹ d⁻¹ for methyl mercury was estimated to be notably higher at 62%. Based on these studies and the estimated risks connected with different remediation techniques a general remediation plan with cost benefit analysis was generated for several sub-regions in the river. Dredging, on-site treatment, and a close disposal of the most contaminated sediments (90,000 m³) was suggested as the first phase of the remediation. The decision regarding the start of remediation will be made during autumn 2008. Conclusions  The sediments in the River Kymijoki are heavily polluted with PCDD/Fs and mercury from earlier chlorophenol, chlor-alkali, and pulp and paper manufacturing. A continuous transport of contaminants is taking place to the Gulf of Finland in the Baltic Sea. The highly increased PCDD/F and Hg levels in river sediments pose an ecotoxicological risk to benthic fauna, to fish-eating predators and probably to human health. The risks posed by mercury exceed those from PCDD/Fs and need to be evaluated for (former) chlor-alkali sites and other mercury releasing industries as one basis for remediation decision making. Recommendations and perspectives  The studies form the basis of a risk management strategy and a plan for possible remediation of contaminated sediments currently under consideration in the Southeast Finland Regional Environment Centre. It is recommended that a detailed restoration plan for the most seriously contaminated areas should be undertaken. Based on current knowledge, the restoration of the whole river is not feasible, considering the current risk caused by the contaminated sediment in the river and the costs of an extensive restoration project. The experiences gained in the present case should be utilized in the evaluation of PCDD/F- and mercury-contaminated sites in other countries. The case demonstrates that the historic reservoirs are of contemporary relevance and should be addressed, e.g., in the national implementation plans of the Stockholm Convention. Electronic supplementary material  The online version of this article (doi:) contains supplementary material, which is available to authorized users.     

Endosulfan in China 1—gridded usage inventories

Background, aim, and scope  Endosulfan, an organochlorine pesticide (OCP), is genotoxic in mammalian cells and generally considered to be toxic and classified by the World Health Organization and the US Environmental Protection Agency as priority pollutants and a nominator for inclusion in a future iteration of the persistent organic pollutants treaty. Endosulfan is a currently used pesticide and still being used worldwide. The general trend of total global endosulfan use has increased continuously since the first year when this pesticide was applied. It is critical to create national endosulfan usage/emission inventories for China to carry out source–receptor relation analysis, risk assessment, and other research related to endosulfan in this country. Chinese inventories have been published for some OCPs, such as technical HCH and lindane, DDT, and chlordane; for endosulfan, however, there has not been any usage inventory available on any scales (national or provincial), although endosulfan has been widely used since 1994 in this country. This is the first part of the work. The goal of this paper is to quantify the historical production and usage of endosulfan in China and to compile gridded historical usage inventories of endosulfan for this country. Based on these usage inventories, emission and residue inventories will be created, which is the goal of the second part of the work. Materials and methods  Due to the lack of national production and usage information of endosulfan in China, a method to estimate the use of endosulfan was developed. First, information of crops on which endosulfan is applied and average endosulfan use and annual application frequencies of endosulfan on these crops were collected. Secondly, usage of endosulfan on each crop was estimated using the national cropland area for each province from Chinese government reports. Finally, with the help of GIS (geographic information system), the usage data of this insecticide was allocated to a grid system, with a 1/4° longitude by 1/6° latitude resolution, with a size for each grid cell of approximately 25 km by 25 km. Results and discussion  The use of endosulfan in agriculture in China started on cotton in 1994, and on wheat, tea, tobacco, apples, and other fruits in 1998. Endosulfan usage on cotton, wheat, tea, tobacco, and apples in China has been estimated to be approximately 25,700 t between 1994 and 2004. The province with the highest usage of endosulfan is Henan Province, with a total usage reaching 4,000 t, followed by the uses in Xinjiang Autonomous Region (3,200 t), Shandong Province (3,000 t), Hebei Province (2,100 t), and Anhui Province (1,900 t). Gridded usage inventories of endosulfan at a 1/4° longitude by 1/6° latitude resolution have been created, which indicate that the intensive endosulfan use was in the south of Hebei Province, west of Shandong Province, east of Henan Province, north of Anhui Province, east of Jiangsu Province, and some areas in Yunnan Province and Xinjiang Autonomous Region. General agreement has been found between the usage data from our estimation and the small amount of usage data published in China. Conclusions  This is the first national gridded endosulfan usage inventory produced for China. The annual applications of endosulfan from 1994 to 2004 in China were estimated based on the total areas of major crops, on which endosulfan was applied, and spatial distribution of the application was generated at provincial and prefecture levels. With the help of GIS, endosulfan usage based on prefecture was transferred to a 1/4° longitude by 1/6° latitude gridding system. The satisfaction of the inventories was supported by the consistence between the estimation of the annual usage and the reported annual production of endosulfan. Recommendations and perspectives  This gridded endosulfan usage inventory created in this study will be improved upon availability of new information of endosulfan. The usage inventories can be used to create gridded emission and residue inventories for this insecticide. It is believed that this work will pave the way for further endosulfan studies in China and beyond.     

Community participatory landscape classification and biodiversity assessment and monitoring of grazing lands in northern Kenya

In this study, we asked the Ariaal herders of northern Kenya to answer "why, what and how" they classified landscape, and assessed and monitored the biodiversity of 10 km(2) of grazing land. To answer the "why question" the herders classified grazing resources into 39 landscape patches grouped into six landscape types and classified soil as 'warm', 'intermediate' or 'cold' for the purpose of land use. For the "what question" the herders used soil conditions and vegetation characteristics to assess biodiversity. Plant species were described as 'increasers', 'decreasers' or 'stable'. The decreaser species were mostly grasses and forbs preferred for cattle and sheep grazing and the increasers were mostly woody species preferred by goats. The herders evaluated biodiversity in terms of key forage species and used absence or presence of the preferred species from individual landscapes for monitoring change in biodiversity. For the "how question" the herders used anthropogenic indicators concerned with livestock management for assessing landscape potential and suitability for grazing. The anthropogenic indicators were related to soils and biodiversity. The herders used plant species grazing preferences to determine the links between livestock production and biodiversity. By addressing these three questions, the study shows the value of incorporating the indigenous knowledge of herders into classification of landscape and assessment and monitoring of biodiversity in the grazing lands. We conclude that herder knowledge of biodiversity is related to the use as opposed to exclusive conservation practices. This type of knowledge is extremely valuable to conservation agencies for establishing a baseline for monitoring changes in biodiversity in the future.     

Economic assessment of managing processionary moth in pine forests: a case-study in Portugal

This paper assesses the private and social profitability of current strategies for managing processionary moth (Thaumetopoea pityocampa) in Portuguese pine forests, looking at economic and environmental costs and benefits. Costs include the expenses for forest treatment and the social costs of threats to human health (dermatitis amongst others); benefits are assessed in terms of both revenue and social benefits such as carbon fixation and recreation. The evaluation was done using Cost Benefit Analysis (CBA) as an analytical framework. While this tool is currently applied to forest and environmental assessment and specific applications to pest management strategies are to be found in agricultural economics, rather few attempts have been made in the field of forest pest management. In order to assess and compare with--without options, a case-study was analysed for the Setúbal Peninsula, south of Lisbon, an area where extensive stands of maritime pine (Pinus pinaster) grow. The exercise has shown that CBA can be a valuable tool for assessing the economic and social profitability of pest management. The results demonstrate that the loss of revenues in the no-management option is not sufficient to make pest management profitable for private forest owners in the short-term. Conversely, a social profit is gained as pest management minimizes health risks for humans and avoids possible recreational losses.     

Cognitive attributes and aesthetic preferences in assessment and differentiation of landscapes

The increasing pace and scale of landscape changes involve objective measurements in order to estimate the effects of changes on people's landscape preferences in a meaningful way. In the literature, some attempts have been made to provide a more conceptual base related to landscape preferences. These concepts and their indicators need to be tested empirically in different contexts and landscape types. In the present study, different items related to theoretical concepts of both aesthetic preference and cognitive rating were examined. They were combined in an in situ questionnaire, which was conducted among undergraduate students in geography during two different field excursions. Stimuli consisted of 11 landscape vistas selected during the excursions. All vistas represent rather rural landscapes but they vary with regard to relief, degree of urbanisation, and degree of agricultural land use. Statistical analysis of all data yielded significant correlations between aesthetic and cognitive ratings. However, these correlations did not appear to be very strong. When considering landscape vistas separately, the relations between all cognitive ratings seemed to vary. Further, not all cognitive aspects had an equal predicting value for aesthetic preference. Moreover, this predicting value appeared to vary between different landscape vistas. The groups of interrelated cognitive aspects could not be associated consistently with theoretical concepts. The results demonstrated the inconsistencies existing between the contents of the theoretical concepts and the indicators found within the landscape. The findings argued for the necessity to distinguish between different ratings and landscape types instead of using unitary preference measures and generalized data when studying landscape preference.