Mn/γ-Al2O3催化剂的制备及头孢合成废水的催化臭氧氧化法深度处理

对Mn/γ-Al₂O₃催化剂的制备条件及头孢合成废水的催化臭氧氧化法深度处理工艺条件进行了优化。实验结果表明：以Mn（NO₃）₂溶液为浸渍液,Mn/γ-Al₂O₃催化剂的最优制备条件为浸渍液浓度0.10 mol/L、浸渍时间9 h、焙烧温度400 ℃、焙烧时间2 h;在反应时间为30 min、废水pH为9.0、臭氧通量为4.6 mg/min、催化剂加入量为5 g/L的条件下,当进水COD、BOD₅、ρ（氨氮）和色度分别为220~250 mg/L,8~10 mg/L,10~12 mg/L和60~70倍时,出水COD、BOD₅、ρ（氨氮）和色度的平均去除率分别为53%,30%,33%和93%,出水水质满足GB 21904—2008《化学合成类制药工业水污染物排放标准》的要求。     

分子筛催化剂生产废水的生物处理

采用氨化—硝化—反硝化三段联合生物工艺处理分子筛催化剂生产过程中产生的含有机胺废水。实验结果表明：在氨化过程中,当进水COD稳定为1 200~1 600 mg/L时,出水COD低于300 mg/L,COD去除率稳定在80%左右,当进水ρ（有机氮）为100~160 mg/L时,出水ρ（有机氮）均低于30 mg/L,有机氮去除率大于80%,在整个氨化过程中,出水ρ（氨氮）较进水ρ（氨氮）提高了35~200 mg/L;硝化过程中,当进水ρ（氨氮）小于等于300 mg/L时,出水ρ（氨氮）最终稳定在15 mg/L以内,氨氮去除率大于90%;在反硝化过程中,亚硝酸盐氮去除率基本稳定在98%以上,最终出水COD低于80 mg/L,出水ρ（总氮）低于25 mg/L。     

Recycling and pollution control of the End of Life Vehicles in China

The quantity of vehicles has increased rapidly in recent years in China; however, the recycling of End of Life Vehicles (ELV) faces several problems and barriers including the collection difficulty and the environmental pollution caused by improper dismantling. In this paper, based on analysis of the basic situation regarding management and recycling of ELV in China, the ELV flow was introduced, and the potential ELV quantity was estimated. The current management regulations and policies were summarized, and dismantling and pollution control technologies for ELV recycling were introduced, too. It was suggested that with the rapid growth of ELV quantities, more regulations will be enacted, and the recycling network will be more effective; the dismantling technology and pollution control measures will be upgraded, and the recycling and remanufacturing industries will be more combined. The government should pay more attention to improve the management and supervision of, and encourage the development of, high level enterprises.     

聚四氟乙烯高压密封罐消解样品测定五氧化二钒

利用聚四氟乙烯高压密封罐消解矿石样品测定五氧化二钒,具有操作手续相对简便、轻松、快捷等优点,与传统的硫酸－磷酸混合酸消解或采用碱熔融前处理法比较,相对误差小于１．６％,样品的添加标准回收率为９２．９％～１０３．５％。     

我国非煤矿山安全生产现状、研究与发展

对我国非煤矿山的安全生产现状进行了系统调查,探讨了我国非煤矿山在21世纪开采条件的不利变化以及潜在的事故隐患,提出了确保非煤矿山的安全生产亟待开展的研究课题以及长远安全科技发展规划。     

催化超临界水氧化法去除焦化废水中的氨氮

采用催化超临界水氧化技术处理焦化废水.实验结果表明:升高反应温度、增加反应压力、延长反应时间可提高废水中氨氮去除率;在反应时间为60 s、反应压力为30 MPa、反应温度为460℃的最佳实验条件下,未加入催化剂时的氨氮去除率为53.7％,加入催化剂后,氨氮去除率大幅提高,以MnO2为催化剂时氨氮去除率为86.9％,以CuSO4为催化剂时氨氮去除率为92.4％.     

Modification of ferrite–manganese oxide sorbent by doping with cerium oxide

Fe–Mn oxide and Ce-doped Fe–Mn oxide sorbents were studied on the structural and desulfurization behavior in COS removal from syngas. The effects of cerium oxide on the Fe–Mn oxides have been investigated by XRD, BET, TPR, XPS and TEM methods. Analysis data show that the Ce-doped sorbent has larger specific surface area and better particles’ dispersion compared with non-modified Fe–Mn sorbent. The addition of Ce improves the reduction performance of Fe–Mn species. The desulfurization experiments show that the desulfurization activity of sorbent can be increased because of the promotion of the structural and redox properties by ceria doped. The Ce-doped sorbent can reduce COS from 15,000 ppmv to less than 0.1 ppmv at 325 °C and a space velocity of 1000 h⁻¹.     

水射流技术在放顶煤综采中的应用

介绍水射流技术在放顶煤综采中的应用。通过具体的技术经济指标说明在一定的条件下水系与放顶煤综采相结合是提高采煤效益的新途径。还说明，水射流技术在采矿工业中有着广阔的应用前景。     

战略导弹核武器系统人因工程应用研究

以战略导弹核武器系统的设计、生产、使用与维修为背景，分析了人为失误的定义、原因及分类，并根据模糊图理论，提出了一种评估人员可靠性的双向模糊图模型，并对人因工程学在战略导弹核武器系统的应用，提出了一些看法和建议。     

Effects of Compounded Curing Agents on Properties and Performance of Urea Formaldehyde Resin

The effects of three compounded curing agents on the properties and performance of the urea-formaldehyde (UF) resin were investigated in this study. The compounded curing agents were prepared by mixing ammonium chloride with hexamethylenetetramine, citric acid, and oxalic acid respectively at a ratio of 1:1, named N-H, N–CA, and N–OA, respectively. The curing process, crystallinity, and physical properties were measured, and the three-ply plywood was fabricated to measure its prepress strength, wet shear strength, and formaldehyde emission. Results showed that the compounded curing agents N–CA and N–OA enhanced the initial viscosity, crosslinking density and thermal stability of UF resin. Additionally, the prepress strength of the plywood bonded by UF resin with N–CA and N–OA increased by 82 and 111% respectively compared to the UF resin with NH₄Cl, and the wet shear strength increased by 14 and 16%, the formaldehyde emission decreased by 19 and 42% respectively. However, owing to the short pot-life of these curing agent limited their storage time, the curing agents N–CA and N–OA should be applied to fabricate plywood in winter for obtaining a better bond strength and a lower formaldehyde emission. While the UF resin with N–HT showed a suitable pot-life, so it could be applied to fabricate plywood in summer for long time storage and avoiding procuring problem.