Determination of ametryn in sugarcane and ametryn–atrazine herbicide formulations using spectrophotometric method

A sensitive spectrophotometric method has been developed for determination of ametryn in agricultural samples. The proposed method was based on reaction with pyridine and further coupling with sulfanilic acid to form a colored product. The absorbance was measured at 400 nm with a molar absorptivity of 2.1 × 10⁵ L mol⁻¹ cm⁻¹. The method shows a linear range from 0.2–20 μg mL⁻¹ with limit of detection and limit of quantification 0.16 and 0.54 μg mL⁻¹, respectively. The method has been successfully applied to the determination of ametryn in sugarcane juice and commercial formulations after separation of ametryn from triazine herbicides based on solvent extraction. Recovery values were found to be in the range of 96.0 ± 0.2% to 98.4 ± 0.1%.     

Methyl mercury in fish—a case study on various samples collected from Ganges river at West Bengal

This study investigated the presence of total mercury (Hg) and organic mercury levels in the muscle of 19 common fresh water fish species captured from river Ganges, West Bengal, India. The total mercury level found in our study may not cause any toxic effect, but the methyl mercury (MeHg) level in some freshwater fish species was surprisingly very high and toxically unacceptable. The results of mercury analysis in various specimens indicated that some fish muscles tended to accumulate high levels of Hg, and approximately 50–84% of Hg was organic mercury. A strong positive correlation between mercury levels in muscle with food habit and fish length (age) was found. Wallago attu possessed the highest amount of organic mercury in their muscle tissues, and it was 0.93 ± 0.61 μg Hg/g of wet weight. Whereas in small-sized fishes Eutropiichthys murius, Puntius sarana, Cirrhinus mrigala, Mystus vittatus or Mystus gulio, and Tilapia mossambicus, it was below the detection limit. Contamination in Catla catla (0.32 ± 0.11), Anguilla bengalensis bengalensis (0.26 ± 0.07 μg Hg/g), Chitala chitala (0.25 ± 0.18), Rita rita (0.34 ± 0.14), and Ompok pabda (0.26 ± 0.04) was also above the 0.25 μg Hg/g of wet weight, the limit set by the PFA for the maximum level for consumption of fish exposed to MeHg. Though in Labeo rohita (0.12 ± 0.03), Mastacembelus armatus (0.17 ± 0.02), Pangasius pangasius (0.12 ± 0.16), Bagarius bagarius (0.12 ± 0.01), and Clupisoma garua (0.1 ± 0.01), concentration was below the recommended level, in Lates calcarifer (0.23 ± 0.0) and Mystus aor (0.23 ± 0.1), it was threatening. Interestingly, a low concentration of Hg was found in post-monsoon samples.     

Simulation of soil loss processes based on rainfall runoff and the time factor of governance in the Jialing River Watershed,China

Jialing River is the largest tributary in the catchment area of Three Gorges Reservoir, and it is also one of the important areas of sediment yield in the upper reaches of the Yangtze River. In recent years, significant changes of water and sediment characteristics have taken place. The "Long Control" Project implemented since 1989 had greatly changed the surface appearance of the Jialing River Watershed (JRW), and it had made the environments of the watershed sediment yield and sediment transport change significantly. In this research, the Revised Universal Soil Loss Equation was selected and used to predict the annual average amount of soil erosion for the special water and sediment environments in the JRW after the implementation of the "Long Control" Project, and then the rainfall–runoff modulus and the time factor of governance were both considered as dynamic factors, the dynamic sediment transport model was built for soil erosion monitoring and forecasting based on the average sediment yield model. According to the dynamic model, the spatial and temporal distribution of soil erosion amount and sediment transport amount of the JRW from 1990 to 2007 was simulated using geographic information system (GIS) technology and space-grid algorithm. Simulation results showed that the average relative error of sediment transport was less than 10% except for the extreme hydrological year. The relationship between water and sediment from 1990 to 2007 showed that sediment interception effects of the soil and water conservation projects were obvious: the annual average sediment discharge reduced from 145.3 to 35 million tons, the decrement of sediment amount was about 111 million tons, and decreasing amplitude was 76%; the sediment concentration was also decreased from 2.01 to 0.578 kg/m³. These data are of great significance for the prediction and estimation of the future changing trends of sediment storage in the Three Gorges Reservoir and the particulate non-point source pollution load carried by sediment transport from watershed surface.     

Gas–particle concentration,distribution, and health risk assessment of polycyclic aromatic hydrocarbons at a traffic area of Giza,Egypt

Atmospheric particulate and gaseous polycyclic aromatic hydrocarbons (PAHs) samples were collected from an urban area in Dokki (Giza) during the summer of 2007 and the winter of 2007–2008. The average concentrations of PAHs were 1,429.74 ng/m³ in the particulate phase, 2,912.56 ng/m³ in the gaseous phase, and 4,342.30 ng/m³ in the particulate + gaseous phases during the period of study. Dokki has high level concentrations of PAH compounds compared with many polluted cities in the world. The concentrations of PAH compounds in the particulate and gaseous phases were higher in the winter and lower in the summer. Total concentrations of PAHs in the particulate phase and gaseous phase were 22.58% and 77.42% in summer and 36.97% and 63.03% in winter of the total (particulate + gaseous) concentrations of PAHs, respectively. The gaseous/particulate ratios of PAHs concentration were 3.43 in summer and 1.71 in winter. Significant negative correlation coefficients were found between the ambient temperature and concentrations of the total PAHs in the particulate and gaseous phases. The distribution of individual PAHs and different categories of PAHs based on aromatic ring number in the particulate and gaseous phases during the summer and winter were nearly similar, indicating similar emission sources of PAHs in both two seasons. Benzo(b)fluoranthene in the particulate phase and naphthalene in the gaseous phase were the most abundant compounds. Diagnostic concentration ratios of PAH compounds indicate that these compounds are emitted mainly from pyrogenic sources, mainly local vehicular exhaust emissions. Health risks associated with the inhalation of individual PAHs in particulate and gaseous phases were assessed on the basis of its benzo(a)pyrene equivalent concentration. Dibenzo(a,h)anthracene and benzo(a)pyrene in the particulate phase and benzo(a)pyrene and benzo(a)anthracene in the gaseous phase were the greatest contributors to the total health risks. The relative mean contributions of the total carcinogenic activity (concentrations) of all PAHs to the total concentrations of PAHs were 29.37% and 25.15% in the particulate phase and 0.76% and 0.92% in the gaseous phase during the summer and winter, respectively. These results suggest that PAHs in the particulate phase in the ambient air of Dokki may pose a potential health risk.     

Mixed response in bacterial and biochemical variables to simulated sand mining in placer-rich beach sediments,Ratnagiri, West coast of India

We investigated the influence on bacterial community and biochemical variables through mechanical disturbance of sediment-akin to small-scale mining in Kalbadevi beach, Ratnagiri, a placer-rich beach ecosystem which is a potential mining site. Changes were investigated by comparing three periods, namely phase I before disturbance, phase II just after disturbance, and phase III 24 h after disturbance as the bacterial generation time is ≤7 h. Cores from dune, berm, high-, mid-, and low-tide were examined for changes in distribution of total bacterial abundance, total direct viability (counts under aerobic and anaerobic conditions), culturability and biochemical parameters up to 40 cm depth. Results showed that bacterial abundance decreased by an order from 10⁶ cells g^− 1 sediment, while, viability reduced marginally. Culturability on different-strength nutrient broth increased by 155% during phase II. Changes in sedimentary proteins, carbohydrates, and lipids were marked at berm and dune and masked at other levels by tidal influence. Sedimentary ATP reduced drastically. During phase III, Pearson’s correlation between these variables evolved from non-significant to significant level. Thus, simulated disturbance had a mixed effect on bacterial and biochemical variables of the sediments. It had a negative impact on bacterial abundance, viability and ATP but positive impact on culturability. Viability, culturability, and ATP could act as important indicators reflecting the disturbance in the system at short time intervals. Culturability, which improved by an order, could perhaps be a fraction that contributes to restoration of the system at bacterial level. This baseline information about the potential mining site could help in developing rational approach towards sustainable harnessing of resources with minimum damage to the ecosystem.     

HPLC-FLD determination of 4-nonylphenol and 4-<Emphasis Type="Italic">tert</Emphasis>-octylphenol in surface water samples

A simple, sensitive and reliable HPLC-FLD method for the routine determination of 4-nonylphenol, 4-NP and 4-tert-octylphenol, 4-t-OP content in water samples was developed. The method consists in a liquid–liquid extraction of the target analytes with dichloromethane at pH  3.0–3.5 followed by the HPLC-FLD analysis of the organic extract using a Zorbax Eclipse XDB C8 column, isocratic elution with a mixed solvent acetonitrile/water 65:35, at a flow rate of 1.0 mL/min and applying a column temperature of 40°C. The method was validated and then applied with good results for the determination of 4-NP and 4-t-OP in Ialomi?a River water samples collected each month during 2006. The concentration levels of 4-NP and 4-t-OP vary between 0.08–0.17 μg/L with higher values of 0.24–0.37 μg/L in the summer months for 4-NP, and frequently <0.05 μg/L but also between 0.06–0.09 μg/L with higher values of 0.12–0.16 μg/L in July and August for 4-t-OP and were strongly influenced by sesonial and anthropic factors. The method was also applied on samples collected over 2 years 2007 and 2008 from urban wastewaters discharged into sewage or directly into the rivers by economic agents located in 30 Romanian towns. Good results were obtained when the method was used for analysis of effluents discharged into surface waters by 16 municipal wastewater treatment plants, during the year 2008.     

Trace metals biogeochemistry of Kumaun Himalayan Lakes,Uttarakhand, India

The increasing urbanization, along with tourism, has posed a major threat to the Kumaun Himalayan Lakes, Uttarakhand, India. The total metal concentration in the water, interstitial water, and sediments along with the metal fractionation studies were carried out to understand the remobilization of the trace metals from the sediments of the lakes. The high concentration of the metals in the water column of the lakes generally decreases with depth and the metals release from the sediment is mainly due to the prevalence of anoxic condition at the sediment–water interface and sediment column. The sediment shows that metals Fe and Cr are derived from detrital source, whereas Co, Ni, and Zn are derived mainly from the organic matter dissolution. The sparse correlation of the trace metals with Ti shows most of the metals have chiefly re-precipitated from the water column. The metals speciation studies also supports that metals experience a high rate of anoxic dissolution and their precipitation onto the sediments are determined by the sediment composition and organic matter content. The high concentration of manganese in the interstitial water in the lakes indicates dissolution of organic matter. The released manganese is adsorbed/precipitated as carbonate phase (Nainital Lake) and oxide pahse (in other lakes). The study shows that the trace metals are regenerated from the sediments due to oxyhydroxide dissolution and organic matter decomposition.     

Assessment of sediment quality in the Mediterranean Sea–Boughrara lagoon exchange areas (southeastern Tunisia): GIS approach-based chemometric methods

Concentrations of selected heavy metals (Cd, Pb, Zn, Cu, Mn, and Fe) in surface sediments from 66 sites in both northern and eastern Mediterranean Sea–Boughrara lagoon exchange areas (southeastern Tunisia) were studied in order to understand current metal contamination due to the urbanization and economic development of nearby several coastal regions of the Gulf of Gabès. Multiple approaches were applied for the sediment quality assessment. These approaches were based on GIS coupled with chemometric methods (enrichment factors, geoaccumulation index, principal component analysis, and cluster analysis). Enrichment factors and principal component analysis revealed two distinct groups of metals. The first group corresponded to Fe and Mn derived from natural sources, and the second group contained Cd, Pb, Zn, and Cu originated from man-made sources. For these latter metals, cluster analysis showed two distinct distributions in the selected areas. They were attributed to temporal and spatial variations of contaminant sources input. The geoaccumulation index (I _geo) values explained that only Cd, Pb, and Cu can be considered as moderate to extreme pollutants in the studied sediments.     

Impact of socioeconomic development on ecosystem services and its conservation strategies: a case study of Shandong Province,China

Ecosystems and their components provide a lot of benefits for the welfare of human beings. Coupled with increasing socioeconomic development, most of the rapidly developing and transitional countries and regions have been experiencing dramatic land use changes. This has resulted in a large amount of forestland, grassland, and wetland being occupied as residential and industrial land or reclaimed for arable land, which in turn results in a sharp deterioration of ecosystem services around the world. Shandong Province, an economically powerful province of China, was chosen as a case study in order to capture the impact of socioeconomic development on ecosystem services. By way of the study, land uses and their changes were categorized between 1980 and 2006, and the ecosystem services capital and changes of 111 counties of Shandong Province in different phases were evaluated, as well as the total ecosystem services capital, followed by the zoning of ecosystem services function region of Shandong Province. We found that the counties in mountainous areas and wetlands, where generally the prefectural-level cities are located with a rapid socioeconomic development, experienced a successive deterioration of ecosystem services especially during the 2000s. Finally, three conservation strategies for managing and improving ecosystem services were proposed and discussed with the aim of achieving coordinate and sustainable development of the socioeconomy, environment, and ecosystems not only in Shandong Province but also in other provinces of China, as well as in other developing and transitional countries and regions.     

Even sampling designs generation by charges repulsion simulation

Evenly distributed sampling design is generally considered as an efficient sampling design. It is widely used in sampling for the environmental survey. In this paper, we present a novel method for generating N evenly distributed samples within a given irregular polygon via simulating the movements of some ideal homogeneous point charges. Initially, charges are randomly put into the sampling region; then, they are freed and held orderly; and after enough runs, the charges will finally reach a stable state with all of them having a zero resultant force and velocity; and so they distribute evenly within the region. Their layout can thus be considered as an evenly distributed sampling design. The main advantages of this method are: (1) it is easy to understand and implement; (2) it is efficient in both running and generating better designs. Analysis and experimental results indicate that this method is an efficient and robust method for generating even sampling designs for 2D polygonal sampling region.