Electrostatic Stimulation of Fabric Filtration

The concept of electrostatic stimulation of fabric filtration (ESFF) has been investigated at pilot scale. The pilot unit consisted of a conventional baghouse in parallel with an ESFF baghouse, allowing direct comparison. All results reported in this paper are for pulse-cleaned bags in which the electric field was maintained parallel to the fabric surface. The performance of the ESFF baghouse has been superior to the parallel conventional baghouse by several measures. The ESFF baghouse demonstrated: (1) a reduced rate of pressure drop increase during a filtration cycle, (2) lower residual pressure drop, (3) stable operation at higher face velocities, and (4) improved particle removal efficiency. These benefits can be obtained with only minor modifications to conventional pulse-jet hardware and at low electrical power consumption. The indicated ability to operate at increased face velocities with only modest expenditure for electrical hardware leads to very favorable economic projections.     

Filter Beds: Energy-Efficient Packing Diameter

Factors which help minimize pressure drop at a given level of collection efficiency for a bed packed with roughly spherical collectors are studied here by using the quality factor, the ratio of the single collector collection efficiency to the force per unit area on the single collector. This analysis indicates that energy-efficient designs can be obtained as follows: choose a representative particle size; if impaction predominates, design for an impaction parameter near one; if interception predominates, design for the smallest packing diameters feasible; if gravitational settling predominates, design for the largest packing diameters possible; if diffusion predominates, design for collector Reynolds numbers near 10². Some more general cases are also discussed.     

Resource Recovery from Flue Gas Desulfurization Systems

The cost effective benefits of yielding a flue gas desulfurization (FGD) sludge predominantly composed of CaSO₄·2H₂O, have been previously established. The recovery of this material as FGD by-product gypsum has been demonstrated abroad. Recently U.S. wallboard manufacturers have recognized the viability of this recovery practice. Such techno-economic decision making variables as a) by-product specification, b) transportation costs, and c) location of suitable FGD systems enable the recognition of FGD by-product recovery. Recent investigations of resultant solids content and chloride washing reflect the technical possibility of delivering a suitable product. Commercial and economic factors favor recovery based upon rising disposal and transportation costs. Existing and near term proposed systems surface the technical and commercial problems faced by utilities considering recovery.

Generation of an oxidized FGD sludge consisting of 90⁺% CaSO₄·2H₂O and dewatered to 80⁺% solids is technically achievable by air sparging within the FGD system. Although the product is suitable for land disposal, electric power utilities should consider and evaluate by-product recovery. U.S. wallboard manufacturers have established technical criteria for FGD by-product gypsum. Percent CaSO₄·2H₂O, final solids content, particle size, and chloride content are primarily technical parameters. Technology exists within the FGD industry to satisfy these criteria and results are discussed.

Economic factors comparing mining costs, transportation costs, and disposal costs are developed for specific utility projects. Such comparison established generalized financial criteria for a given utility to develop the economic reasonableness of considering FGD byproduct recovery.

End product user perspectives are presented providing electric utilities with a realistic appreciation for by-product recovery potential. Location of existing wallboard plants highlight potential recovery regions. Quality control problems are discussed in terms of generating a by-product rather than a disposable material.     

Comparison of Air Pollutant Emissions from Vaporizing and Air Atomizing Waste Oil Heaters

Information presented in this paper is directed to individuals concerned with emissions from combustion of waste crankcase oil for space heating. Studies were performed to characterize gaseous and particulate emissions and vaporizing pot solid residues resulting from the combustion of waste crankcase oil. Two types of waste oil burners were tested. One was a vaporizing oil burner rated at 35.2 kW (120,000 Btu/h heat input), and the other was an air atomizing oil burner rated at 73.3 kW (250,000 Btu/h heat input). Except for NO_X and SO_X, gaseous emissions were similar to those from conventional distillate oil combustion. NO_X and SO_X emissions were higher due to higher fuel nitrogen and sulfur concentrations. Waste oil from automotive use showed higher inorganic levels than crankcase oil used for truck engine lubrication. Both burner types discharged high levels of metallic species, but the air atomizing unit had much higher stack emission levels than did the vaporizing pot system. Also, particulate loading levels were an order of magnitude higher for the air atomizing burner than for the vaporizing pot burner when firing the waste oils. However, the vaporizing pot burner generated a waste residue containing the majority of its elemental emissions. Elements which exceeded threshold limit values for one or both heaters were cadmium, chromium, cobalt, copper, iron, lead, nickel, phosphorus, and zinc. However, the nickel and much of chromium appeared to be a sampling artifact caused by the stainless steel sampling system.     

Evaluation of Selected Gaseous Halocarbons for Use in source Test Performance Audits

A repository of 38 gaseous organic compounds in compressed gas cylinders has been established by EPA. This repository was established to provide standards for source test performance audits, that is, quantitative quality assurance tests. Among these compounds are ten halogenated organic species, which are the focus of this paper.

Stability studies of all ten compounds have been performed to determine the feasibility of using them as performance audit standards. Results indicate that all of the halocarbons tested are adequately stable to be used as reliable audit standards.

Subsequent to completion of stability studies, four of the ten halocarbons were used in source test performance audits. Results are available at this time for two of the four compounds; the results show agreement within 10% of the concentrations previously established by Research Triangle Institute.     

The Relationship between Cross-Sectional and Time Series Studies

Abstract

There is a dearth of information on dust emissions from sources that are unique to the U.S. Department of Defense testing and training activities. However, accurate emissions factors are needed for these sources so that military installations can prepare accurate particulate matter (PM) emission inventories. One such source, coarse and fine PM (PM₁₀ and PM_2.5) emissions from artillery backblast testing on improved gun positions, was characterized at the Yuma Proving Ground near Yuma, AZ, in October 2005. Fugitive emissions are created by the shockwave from artillery pieces, which ejects dust from the surface on which the artillery is resting. Other contributions of PM can be attributed to the combustion of the propellants. For a 155–mm howitzer firing a range of propellant charges or zones, amounts of emitted PM₁₀ ranged from ～19 g of PM₁₀ per firing event for a zone 1 charge to 92 g of PM₁₀ per firing event for a zone 5. The corresponding rates for PM_2.5 were ～9 g of PM_2.5 and 49 g of PM_2.5 per firing. The average measured emission rates for PM₁₀ and PM_2.5 appear to scale with the zone charge value. The measurements show that the estimated annual contributions of PM₁₀ (52.2 t) and PM_2.5 (28.5 t) from artillery backblast are insignificant in the context of the 2002 U.S. Environment Protection Agency (EPA) PM emission inventory. Using national–level activity data for artillery fire, the most conservative estimate is that backblast would contribute the equivalent of 5 x 10^–4% and 1.6 x 10^–3% of the annual total PM₁₀ and PM_2.5 fugitive dust contributions, respectively, based on 2002 EPA inventory data.     

Treatment Technologies For Hazardous Wastes: Part IV A Review of Alternative Treatment Processes for Metal Bearing Hazardous Waste Streams

The U.S. Congress and the U.S. Environmental Protection Agency believe that treatment and recovery techniques should be given maximum priority when considering methods for managing the nation's generated hazardous waste. A prohibition for the disposal of certain categories of hazardous wastes either directly onto or into the land without being treated to an accepted degree prior to such disposal practice has been promulgated.¹ Wastes containing toxic metals and cyanide complexes have been selected as a group to be restricted. Due to the high generation rate associated with this category, a large capacity of waste treatment processing will be required. Existing and emerging treatment alternatives which are or have the potential to be employed for waste treatment of metal bearing wastes are presented in this paper.