Persistence of repeated triadimefon application and its impact on soil microbial functional diversity

The effects of repeated applications of the fungicide triadimefon in agricultural soil on the microbial functional diversity of the soil and on the persistence of the fungicide in the soil were investigated under laboratory conditions. The degradation half-lives of triadimefon at the recommended dosage, simulated by a first-order kinetic model, were 23.90, 22.95, and 21.52 days for the first, second, and third applications, respectively. Throughout this study, no significant inhibition of the Shannon-Wiener index (H') was observed. However, the Simpson index (1/D) and the McIntosh index (U) were obviously reduced (p ≤ 0.05) during the initial 3 days after the first triadimefon application and thereafter, gradually recovered to or exceeded the level of the control soil. A similar trend in variation but with a faster recovery in the 1/D and U was observed after the second and third triadimefon applications, respectively. Taken together, the above results indicate that the repeated application of triadimefon enhanced the degradation rate of the fungicide and the recovery rate of the soil microbial functional diversity. It is concluded that repeated triadimefon applications in soil have a transient or temporary inhibitory effect on soil microbial communities.     

Biodegradation of high molecular weight PAHs using isolated yeast mixtures: application of meta-genomic methods for community structure analyses

Bioaugmentation for the removal of polyaromatic hydrocarbons (PAHs) from wastewater using bacteria and yeasts is considered environment-friendly and a cost-effective technique. The effectiveness of this biodegradation system depends on the stability of inoculated microorganisms and the availability of nutrients. This study is aimed to investigate the removal of high molecular weight (HMW)-PAHs from biologically treated produced water using different biological systems. Three systems, inoculated with activated sludge (AS), the mixture of five yeast strains (MY), and the mixture of AS and the five yeast strains (SY), respectively, were constructed, and their performance for the removal of HMW-PAHs was compared over 10 weeks. The effluent of the biologically treated produced water from an oilfield was used as the influent after chrysene and benzo(a)pyrene were spiked as HMW-PAHs. Polymerase chain reaction-based denaturing gradient gel electrophoresis (PCR-DGGE) and fluorescent in situ hybridization (FISH) techniques were used to examine the changes in the structures and abundances of the bacterial and yeast communities in these three systems. Only SY and MY systems were capable to remove chrysene (90.7 % and 98.5 %, respectively) and benzo(a)pyrene (80.7 % and 95.2 %, respectively). PCR-DGGE analysis confirmed that all of the five yeast strains inoculated remained in the SY and MY systems, while FISH results showed that the relative abundance of yeast in the SY and MY systems (10.6 % to 21.9 %, respectively) were significantly higher than AS system (2.3 % to 7.8 %, respectively). The relative abundances of the catechol 2,3-dioxygenase (C23O) indicated that the copy number ratios of benzene ring cleavage gene C23O in the yeast amended systems were much higher than that in the AS system. In this study, all of the three systems were effective in removing the low molecular weight (LMW)-PAHs, while HMW-PAHs including chrysene and benzo(a)pyrene were efficiently removed by MY and SY systems, not by AS system. The high HMW-PAHs removal in the MY and SY bioaugmentation systems possibly attributed to the inoculation of the mixed yeast culture. By combining the PCR-DGGE results with the FISH analyses, it was found that yeast probably consisting mainly of the five inoculated strains inhabited in the two bioaugmentation systems as a dominant population. The relatively higher performance of the SY system might be attributed to the suspended growth type which permitted a more efficient contact between microbial cells and contaminants. The bioaugmentation systems (SY and MY) were successfully established by inoculating with five nonindigenous yeast strains and demonstrated high performance in removal of HMW-PAHs.     

Characteristics of precipitation chemistry at Lushan Mountain, East China: 1992–2009

Introduction

Trends in precipitation pH and conductivity during 1992?C2009, and in ionic compositions from January 2007 to June 2009, are reported from Lushan Mountain, one of the highest mountains in mid-east China. Annual mean pH was in the range of 4.35?C5.01 and showed a statistically very significant (P?P?Results and discussions Over the period of study, Lushan Mountain received more rainfall in spring and summer. The pH values varied seasonally with winter minima. The winter multiyear seasonal mean pH was 4.35. The corresponding summer value was 4.88. SO ₄ ^2? and NO ₃ ^? were the main anions, and NH ₄ ⁺ and Ca²⁺ the main cations. The anion to cation ratio was 0.8?C1.0, and that of [SO ₄ ^2? ] to [NO ₃ ^? ] was 2.4-3.0, much lower than that of the 1980s. However, sulfuric acid was still the main acid present. The ratio of [NH ₄ ⁺ ] to [Ca²⁺] was about 1.0, suggesting that these two alkaline substances provided close acid neutralizing capacity. The ratio of [Cl^?] to [Na⁺] was about 0.67, somewhat lower than that of natural precipitation.

Conclusions

Ionic composition varied seasonally and was closely correlated to the amounts of rainfall and pollution. Trajectory analyses showed that the trajectories to Lushan Mountain could be classified in six clusters and trajectories originating from the South Sea and the areas surrounding Lushan Mountain had the greatest impacts on precipitation chemistry.     

Mo-N-TiO_2光催化剂的制备、表征及其活性提高机制

以钼酸铵和氨水分别为钼源和氮源,采用溶胶-凝胶法制备了Mo-N-TiO2光催化剂,并对其进行了XRD、XPS和UV-visDRS表征。XRD结果表明,Mo、N共掺杂有效抑制了TiO2晶粒的生长,提高了TiO2由锐钛矿向金红石相的转变温度。UV-vis表明,Mo-N-TiO2光催化剂可见光吸收能力增强,吸收带边明显＂红移＂,且钼酸铵添加量（相对TiO2）为0.5%的样品＂红移＂程度最大,最大吸收带边为550 nm。XPS分析结果表明,Mo取代了TiO2晶格中的部分Ti4＋,以Mo6＋形式存在的,而N以Ti—N及N—Ti—O形式存在。以罗丹明B为模型污染物,重点考察了钼酸铵添加量与焙烧温度对Mo-N-TiO2光催剂性能的影响。结果表明,400℃焙烧下、钼酸铵添加量为0.5%的样品催化活性最好。模拟太阳光下光照120min对罗丹明B的降解率达到96.8%,是纯TiO2的2.42倍。     

Carbonyl emissions from vehicular exhausts sources in Hong Kong

Vehicular emission (VE) is one of the important anthropogenic sources for airborne carbonyls in urban area. Six types of VE-dominated samples were collected at representative locations in Hong Kong where polluted by a particular fueled type of vehicles, including (i) a gas refilling taxis station (liquefied petroleum gas [LPG] emission); (ii) a light-duty passenger car park (gasoline emission); (iii) a minibus station (diesel emission); (iv) a single-deck-bus depot (diesel emission); (v) a double-deck-bus depot (diesel emission); and (vi) a whole-food market entrance for light- and heavy-duty vehicles (diesel emission). A total of 15 carbonyls in the samples were quantified. Formaldehyde was the most abundant carbonyl among the VE-dominated samples, and its contribution to the total quantified amount on a molar basis ranged from 54.8% to 60.8%. Acetaldehyde and acetone were the next two abundant carbonyls. The carbonyls were quantified at three roadside locations in Hong Kong. The highest concentrations of formaldehyde and acetaldehyde, 22.7 +/- 8.4 and 6.0 +/- 2.8 microg/m3, respectively, were determined in the samples collected at a main transportation gate for goods between Hong Kong and Mainland China. The total quantified carbonyl concentration, 37.9 +/- 9.3 microg/m3, was the highest at an entrance of a cross-harbor tunnel in downtown area. The theoretical carbonyls compositions of the three roadside locations were estimated according to the VE-dominated sample profiles and the statistics on vehicle numbers and types during the sampling period. The measured compositions of formaldehyde were much higher than the theoretical compositions in summer, demonstrating that photochemical reactions significantly contributed to the formaldehyde production in the roadsides.     

Second-order chlorine decay and trihalomethanes formation in a pilot-scale water distribution systems

It is well known that model-building of chlorine decay in real water distribution systems is difficult because chlorine decay is influenced by many factors (e.g., bulk water demand, pipe-wall demand, piping material, flow velocity, and residence time). In this paper, experiments were run to investigate the kinetic model of chlorine decay and the formation model of trihalomethanes (THMs) in pilot-scale water distribution systems. Experimental results show that the rate constants of chlorine decay, including wall decay and bulk decay, increasing with temperature. Moreover, the kinetic model of chlorine decay and the formation model of THMs describe experiment data of pilot-scale water distribution systems. The effect of different piping material on chlorine decay and THMs formation were also investigated. The rate constants of chlorine decay are ranked in order: stainless steel pipe, ductile iron pipe, and last, polyethelene pipe because wall decay is the largest in stainless steel pipe than that in other piping material. Correspondingly, the rate of THMs formation follows the order of stainless steel pipe, ductile iron pipe, and last, polyethelene pipe because of less chlorine in bulk water reacting with the trihalomethane formation potential (THMFP).     

应用表面活性剂-生物柴油微乳液去除污染土壤中多环芳烃

针对修复焦化厂高浓度多环芳烃污染土壤高成本的现实,采用以非食用性植物油、生物柴油、表面活性剂及其乳化合成的微乳液为淋洗剂,比较不同淋洗剂的淋洗效果。结果表明乳化合成的微乳液对焦化厂土壤中多环芳烃的总去除率高于单独使用表面活性剂为淋洗剂对土壤中多环芳烃的总去除率,说明生物柴油及植物油与表面活性剂乳化形成的微乳液对原污染土壤中的多环芳烃具有显著的增溶作用。1%TW-80和2.5%TW-80对土壤中多环芳烃总去除率分别为11%和14%;以2.5%TW-80为原料乳化合成的微乳液的淋洗去除率较以1%TW-80为原料乳化合成的微乳液高,总去除率分别为15%～30%和11%～18%;以生物柴油为原料乳化合成的微乳液的淋洗去除率较以植物油为原料乳化合成的微乳液高,分别为17%～30%和15%～23%,且对多环芳烃的去除率与其辛醇水分配系数(logKow)呈线性相关关系。     

絮凝-微纳气泡法处理采油废水

对采自胜利油田的采油废水,分别进行了聚硅硫酸铁(PFSS)絮凝法、微纳气泡法和絮凝-微纳气泡联合法处理,考察了处理过程对采油废水水质和所配制聚合物(部分水解聚丙烯酰胺)溶液粘度的影响。结果表明,均可有效降低废水的矿化度、油含量和悬浮物含量,明显提高用其配制的聚合物溶液的粘度;联合处理效果明显高于单独采用絮凝或微纳气泡处理的效果。所处理后的废水可有望代替淡水用于油田现场配制聚合物驱油体系,在消除油田污水环境污染的同时,可节约淡水资源。     

Mo-N-TiO2光催化剂的制备、表征及其活性提高机制

以钼酸铵和氨水分别为钼源和氮源,采用溶胶-凝胶法制备了Mo-N-TiO2光催化剂,并对其进行了XRD、XPS和UV-visDRS表征。XRD结果表明,Mo、N共掺杂有效抑制了TiO2晶粒的生长,提高了TiO2由锐钛矿向金红石相的转变温度。UV-vis表明,Mo-N-TiO2光催化剂可见光吸收能力增强,吸收带边明显"红移",且钼酸铵添加量(相对TiO2)为0.5%的样品"红移"程度最大,最大吸收带边为550 nm。XPS分析结果表明,Mo取代了TiO2晶格中的部分Ti4+,以Mo6+形式存在的,而N以Ti—N及N—Ti—O形式存在。以罗丹明B为模型污染物,重点考察了钼酸铵添加量与焙烧温度对Mo-N-TiO2光催剂性能的影响。结果表明,400℃焙烧下、钼酸铵添加量为0.5%的样品催化活性最好。模拟太阳光下光照120min对罗丹明B的降解率达到96.8%,是纯TiO2的2.42倍。     

磁性海泡石吸附Cr(VI)特性及动力学

采用化学共沉淀法合成磁性海泡石,通过静态吸附实验研究磁性海泡石对Cr(Ⅵ)的吸附特性及其动力学。结果表明,磁性海泡石对Cr(Ⅵ)的吸附在90 min内即可达到平衡;体系的初始pH是影响磁性海泡石吸附Cr(Ⅵ)性能的重要因素;当废水中Cr(Ⅵ)的初始浓度为50 mg/L时,磁性海泡石的适宜投加量为10 g/L;随反应温度的升高,磁性海泡石对Cr(Ⅵ)的吸附量增加;温度为25、35和45℃时,磁性海泡石对Cr(Ⅵ)的饱和吸附量分别为3.32、3.72、4.08 mg/g;吸附动力学曲线可以用拟二级反应动力学模型拟合;内扩散和液膜扩散联合控制Cr(Ⅵ)在磁性海泡石上的吸附过程,其中内扩散的控速作用大于液膜扩散。