Increased bioavailability of metals in two contrasting agricultural soils treated with waste wood-derived biochar and ash

Recycled waste wood is being increasingly used for energy production; however, organic and metal contaminants in by-products produced from the combustion/pyrolysis residue may pose a significant environmental risk if they are disposed of to land. Here we conducted a study to evaluate if highly polluted biochar (from pyrolysis) and ash (from incineration) derived from Cu-based preservative-treated wood led to different metal (e.g., Cu, As, Ni, Cd, Pb, and Zn) bioavailability and accumulation in sunflower (Helianthus annuus L.). In a pot experiment, biochar at a common rate of 2 % w/w, corresponding to ～50 t ha^?1, and an equivalent pre-combustion dose of wood ash (0.2 % w/w) were added to a Eutric Cambisol (pH 6.02) and a Haplic Podzol (pH 4.95), respectively. Both amendments initially raised soil pH, although this effect was relatively short-term, with pH returning close to the unamended control within about 7 weeks. The addition of both amendments resulted in an exceedance of soil Cu statutory limit, together with a significant increase of Cu and plant nutrient (e.g., K) bioavailability. The metal-sorbing capacity of the biochar, and the temporary increase in soil pH caused by adding the ash and biochar were insufficient to offset the amount of free metal released into solution. Sunflower plants were negatively affected by the addition of metal-treated wood-derived biochar and led to elevated concentration of metals in plant tissue, and reduced above- and below-ground biomass, while sunflower did not grow at all in the Haplic Podzol. Biochar and ash derived from wood treated with Cu-based preservatives can lead to extremely high Cu concentrations in soil and negatively affect plant growth. Identifying sources of contaminated wood in waste stream feedstocks is crucial before large-scale application of biochar or wood ash to soil is considered.     

Review of Italian experience on automotive shredder residue characterization and management

Automotive Shredder Residue (ASR) is a special waste that can be classified as either hazardous or non hazardous depending on the amount of hazardous substances and on the features of leachate gathered from EN12457/2 test. However both the strict regulation concerning landfills and the EU targets related to End-of-Life Vehicles (ELVs) recovery and recycling rate to achieve by 2015 (Directive 2000/53/EC), will limit current landfilling practice and will impose an increased efficiency of ELVs valorization. The present paper considers ELVs context in Italy, taking into account ASRs physical–chemical features and current processing practice, focusing on the enhancement of secondary materials recovery. The application in waste-to-energy plants, cement kilns or metallurgical processes is also analyzed, with a particular attention to the possible connected environmental impacts. Pyrolysis and gasification are considered as emerging technologies although the only use of ASR is debatable; its mixing with other waste streams is gradually being applied in commercial processes. The environmental impacts of the processes are acceptable, but more supporting data are needed and the advantage over (co-)incineration remains to be proven.     

Using long-term data for a reintroduced population to empirically estimate future consequences of inbreeding

Inbreeding depression is an important long-term threat to reintroduced populations. However, the strength of inbreeding depression is difficult to estimate in wild populations because pedigree data are inevitably incomplete and because good data are needed on survival and reproduction. Predicting future population consequences is especially difficult because this also requires projecting future inbreeding levels and their impacts on long-term population dynamics, which are subject to many uncertainties. We illustrate how such projections can be derived through Bayesian state-space modeling methods based on a 26-year data set for North Island Robins (Petroica longipes) reintroduced to Tiritiri Matangi Island in 1992. We used pedigree data to model increases in the average inbreeding level (F ) over time based on kinship of possible breeding pairs and to estimate empirically N_e/N (effective/census population size). We used multiple imputation to model the unknown components of inbreeding coefficients, which allowed us to estimate effects of inbreeding on survival for all 1458 birds in the data set while modeling density dependence and environmental stochasticity. This modeling indicated that inbreeding reduced juvenile survival (1.83 lethal equivalents [SE 0.81]) and may have reduced subsequent adult survival (0.44 lethal equivalents [0.81]) but had no apparent effect on numbers of fledglings produced. Average inbreeding level increased to 0.10 (SE 0.001) as the population grew from 33 (0.3) to 160 (6) individuals over the 25 years, giving a ratio of 0.56 (0.01). Based on a model that also incorporated habitat regeneration, the population was projected to reach a maximum of 331–1144 birds (median 726) in 2130, then to begin a slow decline. Without inbreeding, the population would be expected stabilize at 887–1465 birds (median 1131). Such analysis, therefore, makes it possible to empirically derive the information needed for rational decisions about inbreeding management while accounting for multiple sources of uncertainty.     

Source attribution and quantification of benzene event emissions in a Houston ship channel community based on real-time mobile monitoring of ambient air

A mobile laboratory equipped with a proton transfer reaction mass spectrometer (PTR-MS) operated in Galena Park, Texas, near the Houston Ship Channel during the Benzene and other Toxics Exposure Study (BEE-TEX). The mobile laboratory measured transient peaks of benzene of up to 37 ppb_v in the afternoon and evening of February 19, 2015. Plume reconstruction and source attribution were performed using the four-dimensional (4D) variational data assimilation technique and a three-dimensional (3D) micro-scale forward and adjoint air quality model based on mobile PTR-MS data and nearby stationary wind measurements at the Galena Park Continuous Air Monitoring Station (CAMS). The results of inverse modeling indicate that significant pipeline emissions of benzene may at least partly explain the ambient concentration peaks observed in Galena Park during BEE-TEX. Total pipeline emissions of benzene inferred within the 16-km² model domain exceeded point source emissions by roughly a factor of 2 during the observational episode. Besides pipeline leaks, the model also inferred significant benzene emissions from marine, railcar, and tank truck loading/unloading facilities, consistent with the presence of a tanker and barges in the Kinder Morgan port terminal during the afternoon and evening of February 19. Total domain emissions of benzene exceeded corresponding 2011 National Emissions Inventory (NEI) estimates by a factor of 2–6.

Implications:?Port operations involving petrochemicals may significantly increase emissions of air toxics from the transfer and storage of materials. Pipeline leaks, in particular, can lead to sporadic emissions greater than in emission inventories, resulting in higher ambient concentrations than are sampled by the existing monitoring network. The use of updated methods for ambient monitoring and source attribution in real time should be encouraged as an alternative to expanding the conventional monitoring network.     

Composition and management of rechargeable electric torch wastes in Ibadan,Nigeria

The consumption, disposal, material and chemical compositions of rechargeable electric torch wastes (RETWs) were investigated in Ibadan, Nigeria. Twenty-five RETWs of ten models were collected and disassembled. Their battery electrodes (BEs) and printed circuit boards (PCBs) were acid digested and leached using United States Environmental Protection Agency (USEPA) method 3050B and USEPA Method 1311, respectively. The digests and extracts were analysed for total and extractable Pb, Cd, Cr and Ni using atomic absorption spectrophotometer. The US Test method (CPSC-CH-E 1002-08) was used for digestion of the plastic components. Two hundred questionnaires were distributed to users in Ibadan to determine their usage of RETs and their management when spent. The results indicated that BEs contributed the highest percentage (44 %) component, followed by plastic (38 %). Other components include metal, PCBs, glass and wire. Of the respondents, 61.9 % dispose their spent torches in dumpsites. The mean ± SD concentrations of Pb, Cd, Cr and Ni in the BEs were 500 ± 109 g/kg, 3.94 ± 6.84 mg/kg, 0.33 ± 0.88 mg/kg, 1.68 ± 0.74 mg/kg respectively; in the PCBs, they were 684 ± 42 g/kg, 13.7 ± 17.8 mg/kg, 13.5 ± 10.2 mg/kg and 193 ± 437 mg/kg; and in the plastics, they were 14.1 g/kg, 5.33 mg/kg, 17 mg/kg, and 4.67 mg/kg respectively. The extractable Pb in BE (2670 mg/L) and PCBs (235 mg/L) exceeded the Toxicity Characteristics Leaching Procedure (TCLP) limit of 5 mg/L. RETWs present potential environmental problems in the absence of effective recycling.     

Dissipation kinetics,safety evaluation,and assessment of pre-harvest interval (PHI) and processing factor for kresoxim methyl residues in grape

A field dissipation study was conducted to evaluate the pre-harvest interval (PHI) and processing factor (PF) for kresoxim methyl (Ergon 44.3 SC) residues in grapes and during raisin making process at recommended dose (RD) and double the recommended dose (DRD). Kresoxim methyl residues dissipated following 1st-order kinetics with a half-life of 10 and 18 days at RD and DRD, respectively. The PHIs with respect to the European Union maximum residue limit (EU-MRL) of 1 mg kg^?1 for grapes were 13 and 30 days at RD and DRD, respectively. The degradation data during grape to raisin making process were best fitted to nonlinear 1st?+?1st-order kinetics with a half-life ranging between 4 and 8 days for both shade drying and with raisin dryer at different doses. The PFs were 1.19 and 1.24 with shade drying and 1.09 and 1.10 with raisin dryer, respectively, which indicates concentration of the residues during raisin making process. The dietary exposure of kresoxim methyl on each sampling day was less than the respective maximum permissible intake both at RD and DRD. The residues of kresoxim methyl in market samples of grapes and raisins were well below the EU-MRL and were also devoid of any risk of acute toxicity related to dietary exposure.     

Leaching behaviour of different scrap materials at recovery and recycling companies: Full-, pilot- and lab-scale investigation

Scrap material recovery and recycling companies are confronted with waste water that has a highly fluctuating flow rate and composition. Common pollutants, such as COD, nutrients and suspended solids, potentially toxic metals, polyaromatic hydrocarbons and poly chlorinated biphenyls can exceed the discharge limits. An analysis of the leaching behaviour of different scrap materials and scrap yard sweepings was performed at full-scale, pilot-scale and lab-scale in order to find possible preventive solutions for this waste water problem. The results of these leaching tests (with concentrations that frequently exceeded the Flemish discharge limits) showed the importance of regular sweeping campaigns at the company, leak proof or covered storage of specific scrap materials and oil/water separation on particular leachates. The particulate versus dissolved fraction was also studied for the pollutants. For example, up to 98% of the polyaromatic hydrocarbons, poly chlorinated biphenyls and some metals were in the particulate form. This confirms the (potential) applicability of sedimentation and filtration techniques for the treatment of the majority of the leachates, and as such the rainwater run-off as a whole.