Determination of protective effect of carob (Ceratonia siliqua L.) extract against cobalt(II) nitrate-induced toxicity

Environmental Science and Pollution Research - Cobalt (Co) is widely used in many industrial fields such as batteries and paints. Cobalt, a dangerous heavy metal, can be found in high...     

Comparison of 24 h averaged VOC monitoring results for residential indoor and outdoor air using Carbopack X-filled diffusive samplers and active sampling--a pilot study

Analytical results obtained by thermal desorption GC/MS for 24 h diffusive sampling of 11 volatile organic compounds (VOCs) are compared with results of time-averaged active sampling at a known constant flow rate. Air samples were collected with co-located duplicate diffusive sampling tubes and one passivated canister. A total of eight multiple-component sampling events took place at fixed positions inside and outside three private homes. Subsequently, a known amount of sample air was transferred from the canister to an adsorbent tube for analysis by thermal desorption GC/MS. Results for the 11 most prevalent compounds--Freon 11, 1,3-butadiene, benzene, toluene, tetrachloroethene, ethylbenzene, m,p-xylene, o-xylene, 4-ethyltoluene, 1,3,5-trimethylbenzene, and p-dichlorobenzene--show that the ratio of average study values (diffusive sampling to active sampling) is 0.92 with 0.70 and 1.14 extreme ratios. Absolute percent difference for duplicate samples using diffusive sampling was <10% for the four most prevalent compounds. Agreement between the two sampling approaches indicates that the prediction of approximately constant diffusive sampling rates based on previous laboratory studies is valid under the field conditions.     

SAOZ measurements of NO2 at Aberystwyth

We present in this paper fifteen years' measurements, from March 1991 to September 2005, of stratospheric NO2 vertical columns measured by a SAOZ zenith-sky visible spectrometer. The instrument spent most of its time at Aberystwyth, Wales, with occasional excursions to other locations. The data have been analysed with the WinDOAS analysis program with low-temperature high-resolution NO2 cross-sections and fitting a slit function to each spectrum. Because of a change in detector in May 1998 there is some uncertainty about the relative changes before and after this date, which are partially constrained by the results of an intercomparison exercise. However, the effect of the Mt Pinatubo aerosol cloud is very evident in the data from 1991-94, with a decrease of 10% in NO2 in the summer of 1992 (the SAOZ was located in Lerwick, Scotland during the winter of 1991-92 and observed very low NO2 values but these cannot be directly compared to the Aberystwyth data). To focus more on interannual and long-term variations in NO2, a seasonal variation comprising an annual and semi-annual component was fitted to the morning and evening twilight separately from 1995 to the present. This fit yielded average NO2 columns of 4.08 x 10(15) cm(-2) and 2.68 x 10(15) cm(-2) for the evening and morning twilight, respectively, with a corresponding annual amplitude of +/-2.08 x 10(15) cm(-2) and +/-1.50 x 10(15) cm(-2). Departures from the fitted curve show a trend of 6% per decade, consistent with that reported elsewhere, for the period 1998-2003, but in the past two years a distinct interannual variation of amplitude of approximately 8% has emerged.     

Determination of Steroid Estrogens in Wastewater Treatment Plant of A Controceptives Producing Factory

Steroid estrogens such as estrone (E1), 17β-estradiol (E2), estriol (E3), and 17α-ethynylestradiol (EE2) have been suspected to be the main contaminants, which can affect the endocrine system of animals. Many authors have investigated these chemicals in the domestic wastewater treatment plants (WTP). However, wastewater from industries producing steroid contraceptives has not got ample attention. From the environmental point of view, the four steroids are very significant because even very low concentrations (ng/L) can cause reproductive disturbances in human, livestock and wildlife. The main purpose of the present investigation was to develop an analytical method for the determination of the four steroid estrogens present in WTP of a pharmacy factory, mainly producing contraceptive medicine in Beijing, China. Analysis was performed by solid-phase extraction (SPE) system and liquid chromatography combined with tandem mass spectrometry (LC/MS/MS). The average recoveries from effluent samples ranged from 88% to 103% and the precision of the method ranged from 9% to 4%. Based on 0.5-L wastewater samples, the limit of quantification (LOQ) was determined at 0.7 ng/L for E1, 0.8 for E2, 0.9 ng/L for E3, and 0.5 ng/L for EE2 in influent, and 1.0 ng/L for E2 and EE2, and 2.0 ng/L for E1 and E3 in effluent. In the influent samples, average concentrations of 80, 85, 73 and 155 ng/L were determined for E1, E2, E3 and EE2, respectively, showing that they were removed in this WTP to the extent of 79, 73, 85 and 67%, respectively.     

Comparative Metal Distribution in Hair of Pakistani and Libyan Population and Source Identification by Multivariate Analysis

Using nitric acid-perchloric acid wet digestion based FAAS method ten selected metals (Cd, Co, Cr, Fe, K, Mn, Na, Ni, Pb and Zn) were determined in the scalp hair of male Pakistani and Libyan donors (n = 62), between 3–54 years age and residing in typical urban areas. The study was taken up to identify sources of metal distribution in two diverse population segments exposed to different environments. Sodium emerged with the highest mean hair concentration of 511.0 μg/g and 496.9 μg/g for Libyan and Pakistani donors respectively, followed by K, at 266.2 μg/g and 242.4 μg/g for the two donor categories. Cadmium showed the lowest mean hair concentration for both Pakistani (0.380 μg/g) and Libyan (0.530 μg/g) donors. Levels of Na, K, Pb, Cr and Cd were higher in hair of Libyan donors compared with Pakistani counterparts which showed higher comparative levels of Zn, Fe, Co, Ni and Mn. Strong metal-to-metal correlations were found between Na–K (r = 0.638) and Cd–Co (r = 0.574) for Pakistani donors, while for Libyan donors, Na–K (r = 0.680) and Fe–Mn (r = 0.624) correlations emerged as strongly significant. Only K was found to have a strong positive correlation (r = 0.611) with age for Pakistani donors while this correlation was significantly negative (r = −0.500) for Libyan donors, probably arising from individual food habits. Other metals showed no viable relationship with age. Principal Component Analysis (PCA) and Cluster Analysis (CA) of the data evidenced food, industrial emissions and automobile emissions as possible sources of metal distribution. The results of the present study are compared with those reported for subjects from other regions of the world.     

Kinetics and thermodynamic studies of Methyl Orange removal by polyvinylidene fluoride-PEDOT mats

We report the preparation of poly(3,4-ethylene dioxythiophene) (PEDOT)-modified polyvinylidene fluoride electrospun fibers and their use as a novel adsorbent material for the removal of the anionic dye Methyl Orange (MO) from aqueous media. This novel adsorbent material can be used to selectively remove MO on a wide pH range (3.0–10.0), with a maximum capacity of 143.8 mg/g at pH 3.0. When used in a recirculating filtration system, the maximum absorption capacity was reached in a shorter time (20 min) than that observed for batch mode experiments (360 min). Based on the analyses of the kinetics and adsorption isotherm data, one can conclude that the predominant mechanism of interaction between the membrane and the dissolved dye molecules is electrostatic. Besides, considering the estimated values for the Gibbs energy, and entropy and enthalpy changes, it was established that the adsorption process is spontaneous and occurs in an endothermic manner. The good mechanical and environmental stability of these membranes allowed their use in at least 20 consecutive adsorption/desorption cycles, without significant loss of their characteristics. We suggest that the physical-chemical characteristics of PEDOT make these hybrid mats a promising adsorbent material for use in water remediation protocols and effluent treatment systems.     

Pilot project of mechanical-biological treatment of waste in Brazil

By mechanical-biological treatment (MBT) of residual municipal solid waste the behaviour of landfills can be significantly improved. After MBT the organic content (COD and BOD5), total organic carbon, and total nitrogen in the leachate, as well as the gas production rate, are reduced to values lower than 90% of the fresh untreated waste. The volume of the stabilized material to be disposed on landfills decreases enormously, by up to 70%. The monitoring effort for a landfill constructed under these conditions is reduced to a minimum and the stabilized material can be used in other ways, as material for reforestation, for cover material or for thermal utilization to produce energy. Environmental conditions are important in MBT, as well as waste characteristics. This paper describes the results of a pilot project of MBT performed in Rio de Janeiro, Brazil. The results have shown that this technology can be used successfully in developing countries, with economy for the society and important results for the environment.     

Mechanical-biological waste treatment and the associated occupational hygiene in Finland

A special feature of waste management in Finland has been the emphasis on the source separation of kitchen biowaste (catering waste); more than two-thirds of the Finnish population participates in this separation. Source-separated biowaste is usually treated by composting. The biowaste of about 5% of the population is handled by mechanical-biological treatment. A waste treatment plant at Mustasaari is the only plant in Finland using digestion for kitchen biowaste. For the protection of their employees, the plant owners commissioned a study on environmental factors and occupational hygiene in the plant area. During 1998-2000 the concentrations of dust, microbes and endotoxins and noise levels were investigated to identify possible problems at the plant. Three different work areas were investigated: the pre-processing and crushing hall, the bioreactor hall and the drying hall. Employees were asked about work-related health problems. Some problems with occupational hygiene were identified: concentrations of microbes and endotoxins may increase to levels harmful to health during waste crushing and in the bioreactor hall. Because employees complained of symptoms such as dry cough and rash or itching appearing once or twice a month, it is advisable to use respirator masks (class P3) during dusty working phases. The noise level in the drying hall exceeded the Finnish threshold value of 85 dBA. Qualitatively harmful factors for the health of employees are similar in all closed waste treatment plants in Finland. Quantitatively, however, the situation at the Mustasaari treatment plant is better than at some Finnish dry waste treatment plants. Therefore is reasonable to conclude that mechanical sorting, which produces a dry waste fraction for combustion and a biowaste fraction for anaerobic treatment, is in terms of occupational hygiene better for employees than combined aerobic treatment and dry waste treatment.     

Carbonization of waste PVC to develop porous carbon material without further activation

Efficient removal of chlorine from PVC achieved by two-stage heat-treatment (280 and 410 degrees C) provided chlorine-free isotropic pitch containing additive. The pitch was stabilized and carbonized into porous carbons with surface areas of approximately 300 m2/g. Resultant porous carbons showed three pore structures of supermicropore, micropore and mesopore. The generation of CO2 from the decomposition of the CaCO3 additive in waste PVC is responsible for the development of porous structures. The surface area of the carbonized product increased after the removal of CaO.     

Assessment of long-term leaching from waste incineration air-pollution-control residues

Assessment of long-term leaching from MSWI air-pollution-control (APC) residues is discussed with respect to use in environmental impact assessment, such as life-cycle assessment (LCA). A method was proposed for estimating leaching as a function of the liquid-to-solid (L/S) ratio in a long-term perspective (L/S 5000l/kg). Data for changes in residue pH as a function of L/S was used in combination with pH dependent leaching data to predict leachate concentrations of Al, Ca, Cd, Ba, Mg, Ni, Pb, S, Pb, V and Zn as a function of L/S. Mass balance calculations were used to determine the element fractions leached with respect to L/S. The estimated long-term leaching from a semi-dry residue and a fly ash was compared with short-term leaching determined by batch tests at L/S 10l/kg, both carbonated and non-carbonated versions of the residues were investigated. Generally, very high L/S ratios above 2000l/kg were required to leach 20-30% of the solid contents. However, Ca and S were depleted at L/S 200-900l/kg. The long-term leachate concentrations were found to either remain at the same level as the initial leaching determined by the L/S 10 batch test, or to significantly decrease compared with the initial leaching. Only Al and Zn were found to show higher leachate concentrations at L/S ratios above 3000-5000l/kg. Carbonation generally prolonged the time needed for depletion from the solid residues; however, Ca and S were depleted faster than in the case of non-carbonated residues. This study shows that uncritical use of batch leaching data for assessing the potential leaching is highly problematic, and evaluations of residue disposal should include scenario specific quantification of the long-term leaching.