Water quality test based on dielectrophoretic measurements of fresh water algae Selenastrum capricornutum

A method is described whereby dielectrophoresis of algal cells is used to perform rapid water quality analysis, specifically detecting the presence of CuSO4. The dielectric collection spectrum of the fresh water alga Selenastrum capricornutum was determined for a range of concentrations of CuSO4 from 25 mg L(-1) to 0.25 mg L(-1) for exposure times of 15 min and 18 h. In all cases increasing the concentration of CuSO4 reduced cell collection, but a step reduction was observed in collection between 2 mg L(-1) and 5 mg L(-1). This method has potential for forming a rapid, low-cost test for water quality with broad specificity and significantly reduced analysis time compared to current methods.     

Performance of a small-scale solar-powered adsorption cooling system

In this study, an experimental investigation on the performance of a small-scale residential-size solar-driven adsorption (silica gel-water) cooling system that was constructed at Assiut University campus, Egypt is carried out. As Assiut area is considered as hot, arid climate, field tests for performance assessment of the system operation during the summer season are performed under different environmental operating conditions. The system consists of an evacuated tube with a reflective concentration parabolic surface solar-collector field with a total area of 36 m², a silica gel-water adsorption chiller of 8 kW nominal cooling capacity, and hot and cold water thermal storage tanks of 1.8 and 1.2 m³ in volume, respectively. The results of summer season field test show that under daily solar insolation varying from 21 to 27 MJ/m², the solar collectors employed in the system had high and almost constant thermal efficiency. The daily solar-collector efficiency during the period of system operation ranged from about 50% to 78%. The adsorption chiller performance shows that the chiller average daily coefficient of performance (COP) was 0.41 with the average cooling capacity of 4.4 kW when the cooling-water and chilled-water temperatures were about 31°C and 19°C, respectively. As the chiller cooling water is cooled by the cooling tower in the hot arid area, the cooling water is at a higher temperature than the design point of the chiller. Therefore, an experiment was carried out using the city water for cooling. The results show that an enhancement in the chiller COP by 40% and the chilling power by 17% has been achieved when the city water was 27.7°C.     

Measuring the order in ordered porous arrays: can bees outperform humans?

A method that explains how to quantify the amount of order in “ordered” and “highly ordered” porous arrays is derived. Ordered arrays from bee honeycomb and several from the general field of nanoscience are compared. Accurate measures of the order in porous arrays are made using the discrete radial distribution function (RDF). Nanoporous anodized aluminum oxide (AAO), hexagonal arrays from functional materials, hexagonal arrays from nanosphere lithography, and square arrays defined by interference lithography (all taken from the literature) are compared to two-dimensional model systems. These arrays have a range of pore diameters from ∼60 to 180 nm. An order parameter, OP ₃ , is defined to evaluate the total order in a given array such that an ideal network has the value of 1. When we compare RDFs of man-made arrays with that of our honeycomb (pore diameter ∼5.89 mm), a locally grown version made by Apis mellifera without the use of foundation comb, we find OP ₃ =0.399 for the honeycomb and OP ₃ =0.572 for man’s best hexagonal array. The nearest neighbor peaks range from 4.65 for the honeycomb to 5.77 for man’s best hexagonal array, while the ideal hexagonal array has an average of 5.93 nearest neighbors. Ordered arrays are now becoming quite common in nanostructured science, while bee honeycombs were studied for millennia. This paper describes the first method to quantify the order found in these arrays with a simple yet elegant procedure that provides a precise measurement of the order in one array compared to other arrays.     

A fouling suppression system in submerged membrane bioreactors using dielectrophoretic forces

A novel method was developed to suppress membrane fouling in submerged membrane bioreactors. The method is based on the dielectrophoretic (DEP) motion of particles in an inhomogeneous electrical field. Using a real sample of biomass as feed, the fouling-suppression performance using DEP with different electrical field intensities (60–160 V) and different frequencies (50–1000 Hz) was investigated. The fouling-suppression performance was found to relate closely with the intensity and frequency of the electrical field. A stronger electrical field was found to better recover the filtrate flux. This is because of a stronger DEP force acting on the biomass particles close to the membrane's surface. Above an intensity and frequency value of 130 V and 1 kHz, respectively the permeate flux was reduced due to an electrothermal effect.     

Application of the analytic hierarchy process to select characterization and risk-based decision-making and management methods for hazardous waste sites

Environmental managers at U.S. Department of Defense (DoD) installations overseas are faced with the challenge of managing contaminated sites at these installations with little information on the extent of contamination or the risk posed by the site. In this regard, DoD managers overseas encounter a situation quite similar to the situation faced by decision makers in the U.S. who are managing brownfields. Innovative site characterization and risk-based decision-making methods, which are currently being developed for expeditious application at brownfield sites in the U.S., may also be appropriate for application at overseas DoD sites. In this paper, the analytic hierarchy process (AHP) is used by DoD decision makers to evaluate and rank innovative site characterization technologies and risk-based decision-making and management methods, for use at installations in Korea. Results indicate that for sites with high potential risk the decision makers preferred site characterization technologies that produce data of high quality and a method that can be used to establish credible risk-based remediation goals. This study provides a framework for applying characterization technologies and risk management to poorly characterized contaminated sites in developing countries, where resources for remedial actions may be limited.     

Temperature-Dependent Persistence of Human Norovirus Within Oysters (<Emphasis Type="Italic">Crassostrea virginica</Emphasis>)

This study characterizes the persistence of human norovirus in Eastern oysters (Crassostrea virginica) held at different seawater temperatures. Oysters were contaminated with human norovirus GI.1 (Norwalk strain 8FIIa) by exposing them to virus-contaminated water at 15 °C, and subsequently holding them at 7, 15, and 25 °C for up to 6 weeks. Viral RNA was extracted from oyster tissue and hemocytes and quantitated by RT-qPCR. Norovirus was detected in hemocytes and oysters held at 7 and 15 °C for 6 weeks and in hemocytes and oysters held at 25 °C for up to 2 and 4 weeks, respectively. Results confirm that NoV is quite persistent within oysters and demonstrate that cooler water temperatures extend norovirus clearance times. This study suggests a need for substantial relay times to remove norovirus from contaminated shellfish and suggests that regulatory authorities should consider the effects of water temperature after a suspected episodic norovirus-contamination event.