焚烧飞灰重金属含量及浸出长期变化规律研究

通过对24个飞灰样品的重金属全量消解和高精度X射线荧光光谱法（HDXRF）快速检测结果进行线性回归分析,发现HDXRF法可较准确测定飞灰中Cu、Pb、Zn、Ni和Cd含量（线性回归决定系数R²³0.90）.采用HDXRF法对某焚烧厂飞灰重金属含量6个月快速检测及浸出毒性测定数据统计分析发现：飞灰重金属月均含量较稳定（变异系数CV<0.14）但日均含量波动较大（CV>2.54）;飞灰中Pb、Cu和Zn含量呈正相关（相关系数r>0.78）;金属浸出浓度受浸出液终点pH值影响显著,超标频率依次为Pb（68.9%）、Cd（66.1%）、Ni（24.0%）、Cu（14.2%）和Zn（1.6%）.短期飞灰金属含量和浸出毒性数据受焚烧工况,烟气处理工况和垃圾组分等多种因素共同影响,不具有代表性.为评估垃圾分类源头削减重金属效果,建议采用快速检测方法对焚烧飞灰重金属含量进行长期监测.     

双酚S在两种典型地带性土壤中的吸附/解吸行为研究

采用批平衡实验方法研究了双酚S（BPS）在两种典型地带性土壤中的吸附/解吸行为.结果表明,吸附动力学曲线符合拟二级动力学方程.吸附等温线呈非线性,且同时符合Freundlich和Langmuir方程.相比而言,BPS更易吸附在高有机质含量的黑土中,298 K反应温度下BPS在黑土和红壤上的最大吸附容量分别为497.8和156.6 mg·kg^-1.吸附到两种土壤中的BPS存在解吸滞后现象,这可能是由于BPS以化学吸附和微孔扩散的形式存在于土壤中的缘故.溶液pH与BPS在土壤中的吸附容量呈负相关关系,即中性形态的BPS比阴离子形态的BPS具有更高的吸附容量.与结构类似物双酚A（BPA）的吸附相比,BPS在土壤中的吸附量更低,因此具有更高的迁移能力,可能会引起更高的环境健康风险.本研究结果为了解BPS在土壤中的迁移规律提供了数据支持.     

北部湾南流江流域土地覆盖及生物多样性模拟

以北部湾独流入海河流南流江流域为研究对象,基于研究区2000年和2015年遥感数据解译的土地利用数据以及社会经济等数据,采用CLUE-S模型对未来2030年生态保护情景、自然增长情景以及粮食安全情景的土地利用格局进行了模拟预测,在此基础上采用InVEST模型对流域过去和未来不同情景的生物多样性进行了评估,探讨了流域生物多样性的生境质量和生境退化程度.结果表明：2000~2015年南流江流域建设用地、园地、水域和未利用地呈现出增加趋势,其中建设用地的增幅最大,而耕地和林地减幅最大.流域土地系统中共存在着34种土地网络转移流关系,上游存在24种,中游20种,下游28种,耕地与建设用地、耕地与林地以及林地与园地之间的转换占到流域总土地利用变化的70.74%.CLUE-S模型模拟未来土地利用的Kappa系数达到0.86,表明模型模拟未来情景的土地利用精度满足要求.2000年、2015年、2030年生态保护情景、2030年自然增长情景以及2030年粮食安全情景流域生境质量总得分和平均得分分别为866630,900357,921055,876231,865370和0.7457,0.7747,0.7925,0.7539,0.7466.2030年3种情景的中上游和下游地区生物多样性都呈现出不同程度的改善趋势,而中游地区则表现出退化趋势.     

pH值对亚硝酸盐氧化菌动力学及功能基因的影响

为探究pH值对亚硝酸盐氧化菌（NOB）活性动力学影响,本试验采用序批式活性污泥（SBR）反应器,以富含NOB的活性污泥为对象,基于Monod模型考察不同pH值对NOB活性动力学的影响并进行统计学分析.结果表明,Monod方程可较好地反映不同pH值条件下基质底物浓度对NOB比亚硝态氮氧化速率（SNiOR）的影响,且pH=7.0时动力学参数Ks为（6.167mg/L）,r_max为[1.134g/（g·d）],此时NOB活性最好.利用钟形经验模型进行非线性回归拟合,最大比降解速率（r_max）随pH值的增大呈钟形变化,本试验NOB的最佳pH值为（6.9±0.1）,其中r_max维持在r_opt一半以上的pH值范围（ω）为（3.26±0.4）.以亚硝酸盐氧化还原酶类基因（nxrA、nxrB）为引物,基于荧光定量PCR技术分析结果显示,在不同pH值条件下nxrA基因和nxrB基因拷贝数的变化趋势均与动力学参数（Ks、r_max）的规律一致,且nxrA和nxrB基因在系统的降解过程中起协同作用.     

DOC+CDPF对国III重型柴油货车实际道路排放的影响

利用便携式车载排放测试系统（PEMS）对2辆加装氧化催化转化器（DOC）和催化型柴油颗粒捕集器（CDPF）与否的国III重型柴油货车进行实际道路排放测试.结果表明,2辆改造重型柴油车的CO、THC、固态颗粒物粒数（SPN）和黑碳（BC）实际道路排放因子分别为（1.31±0.37）g/（kW×h）、（0.20±0.03） g/（kW×h）、（7.13×10¹⁰±5.27×10¹⁰）个/（kW×h）和（0.69±0.06）mg/（kW×h）,相对于原始排放（拆除DOC+CDPF）分别降低52.48%、55.69%、99.91%和99.22%.从低速、中速到高速,CO和THC减排比例呈现上升趋势,然而运行工况对SPN和BC减排比例则无显著影响.加装DOC+CDPF会导致NO₂在NO_x中的占比升高,且从低速、中速到高速涨幅依次增大,但对NO_x无明显减排效益,其排放因子为9.53~9.83g/（kW×h）,远高于实验室排放限值.     

Regulated emission characteristics of in-use LNG and diesel semi-trailer towing vehicles under real driving conditions using PEMS

On-road driving emissions of six liquefied natural gas(LNG) and diesel semi-trailer towing vehicles(STTVs) which met China Emission Standard IV and V were tested using Portable Emission Measurement System(PEMS) in northern China.Emission characteristics of these vehicles under real driving conditions were analyzed and proved that on-road emissions of heavy-duty vehicles(HDVs) were underestimated in the past.There were large differences among LNG and diesel vehicles, which also existed between China V vehicles and China IV vehicles.Emission factors showed the highest level under real driving conditions, which probably be caused by frequent acceleration, deceleration, and start-stop.NOx emission factors ranged from 2.855 to 20.939 g/km based on distance-traveled and 6.719–90.557 g/kg based on fuel consumption during whole tests, which were much higher than previous researches on chassis dynamometer.It was inferred from tests that the fuel consumption rate of the test vehicles had a strong correlation with NOx emission, and the exhaust temperature also affected the efficiency of Selected Catalytic Reduction(SCR) aftertreatment system, thus changing the NOx emission greatly.THC emission factors of LNG vehicles were 2.012–10.636 g/km, which were much higher than that of diesel vehicles(0.029–0.185 g/km).Unburned CH_4 may be an important reason for this phenomenon.Further on-road emission tests, especially CH_4 emission test should be carried out in subsequent research.In addition, the Particulate Number(PN) emission factors of diesel vehicles were at a very high level during whole tests, and Diesel Particulate Filter(DPF)should be installed to reduce PN emission.     

Dynamic nano-Ag colloids cytotoxicity to and accumulation by Escherichia coli: Effects of Fe3+, ionic strength and humic acid

Released Ag ions or/and Ag particles are believed to contribute to the cytotoxicity of Ag nanomaterials, and thus, the cytotoxicity and mechanism of Ag nanomaterials should be dynamic in water due to unfixed Ag particle:Ag⁺ ratios. Our recent research found that the cytotoxicity of PVP-Ag nanoparticles is attributable to Ag particles alone in 3 hr bioassays, and shifts to both Ag particles and released Ag⁺ in 48 hr bioassays. Herein, as a continued study, the cytotoxicity and accumulation of 50 and 100 nm Ag colloids in Escherichia coli were determined dynamically. The cytotoxicity and mechanisms of nano-Ag colloids are dynamic throughout exposure and are derived from both Ag ions and particles. Ag accumulation by E. coli is derived mainly from extracellular Ag particles during the initial 12 hr of exposure, and thereafter mainly from intracellular Ag ions. Fe³⁺ accelerates the oxidative dissolution of nano-Ag colloids, which results in decreasing amounts of Ag particles and particle-related toxicity. Na⁺ stabilizes nano-Ag colloids, thereby decreasing the bioavailability of Ag particles and particle-related toxicity. Humic acid (HA) binds Ag⁺ to form Ag⁺-HA, decreasing ion-related toxicity and binding to the E. coli surface, decreasing particle-related toxicity. HA in complex conditions showed a stronger relative contribution to toxicity and accumulation than Na⁺ or Fe³⁺. The results highlighted the cytotoxicity and mechanism of nano-Ag colloids are dynamic and affected by environmental factors, and therefore exposure duration and water chemistry should be seriously considered in environmental and health risk assessments.     

An investigation of changes in water quality throughout the drinking water production/distribution chain using toxicological and fluorescence analyses

Changes in water quality from source water to finished water and tap water at two conventional drinking water treatment plants(DWTPs) were monitored.Beside the routine water quality testing,Caenorhabditis elegans-based toxicity assays and the fluorescence excitation–emission matrices technique were also applied.Both DWTPs supplied drinking water that met government standards.Under current test conditions,both the investigated finished water and tap water samples exhibited stronger lethal,genotoxic and reprotoxic potential than the relative source water sample,and the tap water sample was more lethal but tended to be less genotoxic than the corresponding finished water sample.Meanwhile,the nearly complete removal of tryptophan-like substances and newly generated tyrosine-like substances were observed after the treatment of drinking water,and humic-like substances were identified in the tap water.Based on these findings,toxic pollutants,including genotoxic/reproductive toxicants,are produced in the drinking water treatment and/or distribution processes.Moreover,further studies are needed to clarify the potentially important roles of tyrosine-like and humic-like substances in mediating drinking water toxicity and to identify the potential sources of these contaminants.Additionally,tryptophan-like fluorescence may be adopted as a useful parameter to monitor the treatment performance of DWTPs.Our observations provided insights into the importance of utilizing biotoxicity assays and fluorescence spectroscopy as tools to complement the routine evaluation of drinking water.     

Synergistic effects of Cu species and acidity of Cu-ZSM-5 on catalytic performance for selective catalytic oxidation of n-butylamine

In this work, a series of Cu-ZSM-5 catalysts with different SiO₂/Al₂O₃ ratios (25, 50, 100 and 200) were synthesized and investigated in n-butylamine catalytic degradation. The n-butylamine can be completely catalytic degradation at 350°C over all Cu-ZSM-5 catalysts. Moreover, Cu-ZSM-5 (25) exhibited the highest selectivity to N₂, exceeding 90% at 350°C. These samples were investigated in detail by several characterizations to illuminate the dependence of the catalytic performance on redox properties, Cu species, and acidity. The characterization results proved that the redox properties and chemisorption oxygen primarily affect n-butylamine conversion. N₂ selectivity was impacted by the Brønsted acidity and the isolated Cu²⁺ species. Meanwhile, the surface acid sites over Cu-ZSM-5 catalysts could influence the formation of Cu species. Furthermore, in situ diffuse reflectance infrared Fourier transform spectra was adopted to explore the reaction mechanism. The Cu-ZSM-5 catalysts are the most prospective catalysts for nitrogen-containing volatile organic compounds removal, and the results in this study could provide new insights into catalysts design for VOC catalytic oxidation.     

Ozone pollution characteristics and sensitivity analysis using an observation-based model in Nanjing, Yangtze River Delta Region of China

Ground-level ozone (O₃) has become a critical pollutant impeding air quality improvement in Yangtze River Delta region of China. In this study, we present O₃ pollution characteristics based on one-year online measurements during 2016 at an urban site in Nanjing, Jiangsu Province. Then, the sensitivity of O₃ to its precursors during 2 O₃ pollution episodes in August was analyzed using a box model based on observation (OBM). The relative incremental reactivity (RIR) of hydrocarbons was larger than other precursors, suggesting that hydrocarbons played the dominant role in O₃ formation. The RIR values for NO_X ranged from –0.41%/% to 0.19%/%. The O₃ sensitivity was also analyzed based on relationship of simulated O₃ production rates with reductions of VOC and NO_X derived from scenario analyses. Simulation results illustrate that O₃ formation was between VOCs-limited and transition regime. Xylenes and light alkenes were found to be key species in O₃ formation according to RIR values, and their sources were determined using the Positive Matrix Factorization (PMF) model. Paints and solvent use was the largest contributor to xylenes (54%), while petrochemical industry was the most important source to propene (82%). Discussions on VOCs and NO_X reduction schemes suggest that the 5% O₃ control goal can be achieved by reducing VOCs by 20%. To obtain 10% O₃ control goal, VOCs need to be reduced by 30% with VOCs/NO_X larger than 3:1.