Phosphate recovery with granular acid-activated neutralized red mud: Fixed-bed column performance and breakthrough curve modelling

Granular acid-activated neutralized red mud (AaN-RM) has been successfully prepared with good chemical stability and physical strength. However, its potential for industrial application remains unknown. Therefore, the performance of granular AaN-RM for phosphate recovery in a fixed-bed column was investigated. The results demonstrated that the phosphate adsorption performance of granular AaN-RM in a fixed-bed column was affected by various operational parameters, such as the bed depth, flow rate, initial solution pH and initial phosphate concentration. With the optimal empty-bed contact time (EBCT) of 24.27 min, the number of processed bed volumes and the phosphate adsorption capacity reached 496.95 and 84.80 mg/g, respectively. Then, the saturated fixed-bed column could be effectively regenerated with a 0.5 mol/L HCl solution. The desorption efficiency remained as high as 83.45% with a low weight loss of 3.57% in the fifth regeneration cycle. In addition, breakthrough curve modelling showed that a 5-9-1 feed-forward artificial neural network (ANN) could be effectively applied for the optimization of the fixed-bed adsorption system; the coefficient of determination (R²) and the root mean square error (RMSE) evaluated on the validation-testing data were 0.9987 and 0.0183, respectively. Therefore, granular AaN-RM fixed-bed adsorption exhibits promising potential for phosphate removal and recovery from polluted water.     

干湿法结合工艺回收废弃SCR脱硝催化剂中的钛、钒和钨

利用干湿法结合工艺实现废弃SCR脱硝催化剂中Ti、V和W元素的高效分离和浸出,提出成套废弃SCR脱硝催化剂中Ti、V和W的回收技术。以废弃SCR脱硝催化剂为研究对象,优选Ti、V和W元素最佳浸出工况,研究硫酸溶解法回收TiO₂和有机萃取法回收V₂O₅和WO₃的回收率与纯度。结果表明:酸浸还原浸钒最优工艺条件为温度140℃,液固比30∶1;钠化焙烧浸钨最优工艺条件为煅烧温度750℃,反应物与Na₂CO₃配比（质量比）为1∶1.5,在以上条件下V、W浸出率分别达到97.6%、93.6%。利用硫酸溶解法回收得到的TiO₂产物主要以锐钛矿晶型存在形式,在最佳焙烧温度750℃下,TiO₂回收率达到97.17%,纯度为95.35%。利用有机萃取法回收得到的V₂O₅和WO₃产物的回收率和纯度分别为72.47%、75.43%和93.25%、78.26%。     

UV/H2O2 oxidation of tri(2-chloroethyl) phosphate: Intermediate products, degradation pathway and toxicity evaluation

Tri(2-chloroethyl) phosphate (TCEP) with the initial concentration of 5 mg/L was degraded by UV/H₂O₂ oxidation process. The removal rate of TCEP in the UV/H₂O₂ system was 89.1% with the production of Cl^? and PO₄^3? of 0.23 and 0.64 mg/L. The removal rate of total organic carbon of the reaction was 48.8% and the pH reached 3.3 after the reaction. The oxidative degradation process of TCEP in the UV/H₂O₂ system obeyed the first order kinetic reaction with the apparent rate constant of 0.0025 min^?1 (R²=0.9788). The intermediate products were isolated and identified by gas chromatography-mass spectrometer. The addition reaction of HO? and H₂O and the oxidation reaction with H₂O₂ were found during the degradation pathway of 5 mg/L TCEP in the UV/H₂O₂ system. For the first time, environment risk was estimated via the “ecological structure activity relationships” program and acute and chronic toxicity changes of intermediate products were pointed out. The luminescence inhibition rate of photobacterium was used to evaluate the acute toxicity of intermediate products. The results showed that the toxicity of the intermediate products increased with the increase of reaction time, which may be due to the production of chlorine compounds. Some measures should be introduced to the UV/H₂O₂ system to remove the highly toxic Cl-containing compounds, such as a nanofiltration or reverse osmosis unit.     

Ozone pollution characteristics and sensitivity analysis using an observation-based model in Nanjing, Yangtze River Delta Region of China

Ground-level ozone (O₃) has become a critical pollutant impeding air quality improvement in Yangtze River Delta region of China. In this study, we present O₃ pollution characteristics based on one-year online measurements during 2016 at an urban site in Nanjing, Jiangsu Province. Then, the sensitivity of O₃ to its precursors during 2 O₃ pollution episodes in August was analyzed using a box model based on observation (OBM). The relative incremental reactivity (RIR) of hydrocarbons was larger than other precursors, suggesting that hydrocarbons played the dominant role in O₃ formation. The RIR values for NO_X ranged from –0.41%/% to 0.19%/%. The O₃ sensitivity was also analyzed based on relationship of simulated O₃ production rates with reductions of VOC and NO_X derived from scenario analyses. Simulation results illustrate that O₃ formation was between VOCs-limited and transition regime. Xylenes and light alkenes were found to be key species in O₃ formation according to RIR values, and their sources were determined using the Positive Matrix Factorization (PMF) model. Paints and solvent use was the largest contributor to xylenes (54%), while petrochemical industry was the most important source to propene (82%). Discussions on VOCs and NO_X reduction schemes suggest that the 5% O₃ control goal can be achieved by reducing VOCs by 20%. To obtain 10% O₃ control goal, VOCs need to be reduced by 30% with VOCs/NO_X larger than 3:1.     

杭州湾北岸36种挥发性有机物污染特征及来源解析

为研究杭州湾北岸VOCs（挥发性有机物）的浓度水平、组成特征、反应活性和潜在来源,采用GC-FID在线监测系统对杭州湾北岸环境大气中的36种VOCs开展了为期1 a（2017年12月-2018年11月）的连续观测,采用LOH（VOCs的·OH消耗速率）和OFP（O₃生成潜势）2种方法估算了大气VOCs的反应活性,并利用PMF（正定矩阵因子分解）和CPF（条件概率函数）模型分析其来源.结果表明:①φ（VOCs）小时平均值在冬季（26.47×10-9）最高,夏季（9.76×10-9）最低;全年φ（VOCs）小时平均值为21.24×10-9,其中烷烃、烯烃+炔烃、芳香烃、卤代烃的贡献率分别为33.24%、34.13%、15.63%、17.00%;φ（烷烃）、φ（芳香烃）和φ（卤代烃）呈较明显的昼夜变化特征,φ（烯烃）和φ（炔烃）无明显昼夜变化趋势.②大气VOCs的总LOH和OFP分别为9.39 s-1和220.57 μg/m3,KOH（·OH反应速率常数）和MIR（最大增量反应活性）系数的平均值分别为17.34×10-12 cm3/（molecule·s）和3.31;KOH和MIR系数的平均值分别与间/对-二甲苯的KOH和乙苯的MIR系数接近,表明大气VOCs的化学反应活性较强;VOCs关键活性物种为异戊二烯、乙烯、丙烯、甲苯、二甲苯和顺-2-丁烯.③特征物种相关性分析表明,杭州湾北岸大气存在老化现象,异戊烷和正戊烷受煤燃烧源影响较大,二甲苯和乙苯受溶剂排放源影响较大,甲苯和苯除受机动车尾气影响外,还受其他排放源影响.④PMF和CPF模型来源分析表明,大气VOCs主要来自石化工业源、燃料挥发源、生物质燃烧和煤燃烧源、机动车排放源和溶剂使用源,其中,机动车排放源主要来自西北方向,其他源主要来自西北、西和西南方向.研究显示,杭州湾北岸大气VOCs来源复杂,受周边工业区的影响较大.      

银川市冬季PM2.5重污染特征、来源与成因分析

近年来银川市冬季重污染过程频发,为明确银川市冬季PM_2.5重污染的特征,分析其主要来源及成因,于2016年12月-2017年1月在银川市选取3个采样点开展PM_2.5的样品采集与化学组分分析,利用CMB（化学质量平衡）模型对银川市冬季PM_2.5进行来源解析,对比分析了重污染日与非重污染日污染特征的差异.结果表明:①银川市冬季重污染日ρ（PM_2.5）[（181±33.6）μg/m3]是非重污染日的2.1倍;重污染日和非重污染日的ρ（NO₃-）/ρ（SO₄2-）均小于1,表明燃煤仍是银川市冬季PM_2.5的重要来源.银川市冬季PM_2.5中ρ（SOC）为（14.4±7.34）μg/m3,约占ρ（OC）的65.2%.②与非重污染日相比,重污染日人为源无机元素As、Pb、Cd和Zn质量浓度在ρ（PM_2.5）中的占比分别升高33.2%、18.4%、9.8%和2.9%,表明银川市冬季重污染主要受人为源贡献影响.③源解析结果表明,燃煤源、机动车尾气源、二次离子源和扬尘源是银川市PM_2.5的主要污染源,与非重污染日相比,重污染日机动车尾气源的贡献率明显降低.研究显示,银川市冬季重污染受人为源污染物排放的影响较大,燃煤源是银川市冬季PM_2.5的重要来源.      

基于TMVOC的地下水位波动带苯系物迁移转化模拟

为探究水位波动情况下苯系物的迁移转化规律,提高石油污染场地地下水污染治理精度,以西北某傍河石化场地为研究对象,基于TMVOC模型对特征污染物苯系物开展泄漏模拟,通过情景模拟比较水位波动对苯系物迁移转化的影响,并从污染分布、相间转化等方面,解析地下水位稳定和波动状态下苯系物迁移转化过程差异.结果表明:①TMVOC模型较好地模拟了水位波动状态下苯系物迁移转化过程.②相较于水位稳定状态下,水位波动作用下苯系物污染深度增加0.5 m,污染面积增加25%,总质量增加12 kg.③水位稳定和波动状态下苯系物"气-液-NAPL（Non-Aqueous Phase Liquids）相"占比分别为0.17%、2.03%、97.8%和0.04%、3.69%、96.27%.④NAPL相苯系物饱和度分布与苯系物质量分布呈正相关,水位波动造成NAPL相初始饱和度降低,且初始水位面以下NAPL相饱和度升高.⑤对于苯而言,水位波动状态下非饱和带中苯在液相中的质量是水位稳定状态下的1.11倍,饱和带为10.15倍.研究显示,水位波动显著地影响了苯系物的迁移转化过程,促进了苯系物的溶解,并使更多的苯系物残留在地下介质中.      

某垃圾焚烧厂投产前后周边土壤二英类化合物的分布

为研究垃圾焚烧厂运行对周边土壤二英类化合物（PCDD/Fs）含量的影响,采集了珠三角地区某垃圾焚烧厂投产前和投产后周边土壤样品,分析研究了该垃圾焚烧厂运行对周边土壤中PCDD/Fs含量和组分的变化.结果表明:①2012年（投产前）珠三角地区某垃圾焚烧厂周边土壤PCDD/Fs含量较低,范围为163~591 ng/kg（毒性当量范围为0.198~0.863 ng I-TEQ/kg,I-TEQ为国际毒性当量因子折算的毒性当量值）;2017—2019年（投产后）周边土壤PCDD/Fs含量范围为151~1.75×103 ng/kg（毒性当量范围为0.812~3.88 ng I-TEQ/kg）,与其他研究相比处于较低的水平.②投产后,距该垃圾焚烧厂较近（1.5 km）的采样点（S1）土壤PCDD/Fs含量逐年增长,在较远（5.2 km）但人口较密集的采样点（S3）土壤PCDD/Fs含量整体较高,但呈逐年下降趋势.③投产后,土壤中的17种PCDD/Fs单体组分中,毒性当量贡献率最高的单体为八氯二苯并二英（OCDD）和2,3,4,7,8-五氯二苯并呋喃（2,3,4,7,8-PeCDF）,二者毒性当量贡献率范围为15.7%~45.4%.④在同一采样点土壤PCDD/Fs单体组分年间差异不明显,但同一年份不同采样点差异明显.研究显示,目前该垃圾焚烧厂周边土壤PCDD/Fs含量较低,但仍需要长期监测其可能带来的风险.      

外加氮源影响下铁铝氧化物在土壤氮素转化中的作用

土壤中铁铝氧化物在团聚体稳定性和有机碳吸附方面具有重要作用,而氮添加对土壤氮循环影响的变化也可能与其有关,但是目前尚缺乏在氮循环方面的研究.为了探究铁铝氧化物在土壤氮素转化中的作用,选择福建省建瓯罗浮栲森林土壤为研究对象,采用选择性溶提技术准备不同的土壤——未经处理（T1）的土壤和去除游离态铁铝氧化物（T2）土壤、去除非晶质铁铝氧化物（T3）土壤、去除络合态铁铝氧化物（T4）土壤,在这些土壤中添加不同形态氮（40 mg/kg）——丙氨酸（氨基酸态氮,AA）、硫酸铵（铵态氮,AN）、硝酸钠（硝态氮,NAN）和亚硝酸钠（亚硝态氮,NIN）,进行室内培养试验,分析氮含量变化和氮素转化情况.结果表明:①与CK处理相比,AA和AN处理均增加了T1土壤中w（NH₄+-N）,NAN处理增加了w（NO₃--N）,但低于添加量,表明添加氨基酸和铵态氮均会促进氮矿化,添加硝态氮会增加NO₃--N的固定且抑制其硝化.②在CK处理下,与T1土壤相比,T2和T4土壤中w（NH₄+-N）、w（NO₃--N）和w（氨基酸）均降低,但T3土壤中w（NH₄+-N）和w（氨基酸）增加、w（NO₃--N）降低,表明土壤中游离态氧化铁铝和络合态氧化铁铝的存在有助于氮素矿化,非晶质氧化铁铝有助于硝化.③在不同氮处理下,各土壤的氮含量及其转化速率与CK处理规律相似.与CK处理相比,各氮处理均未显著增加T2和T4土壤中w（NH₄+-N）,且AA和AN处理均未影响T2、T3和T4土壤中w（NO₃--N）和w（氨基酸）.结果显示,氮添加并没有改变铁铝氧化物的作用,其中,矿化和氨化作用均表现为游离氧化铁铝>络合氧化铁铝>非晶质氧化铁铝,硝化作用表现为非晶质氧化铁铝>游离氧化铁铝>络合态氧化铁铝.因此,土壤铁铝氧化物的不同存在状态应该是调节氮素转化的重要土壤条件.      

餐厨垃圾生物有机肥对贫瘠黄褐土改良的研究

为了阐明餐厨垃圾生物有机肥改良贫瘠土壤的作用机制,以贫瘠黄褐土为研究对象,通过不施肥、长期（>5 a）施用化肥、中长期（5 a）施用少量餐厨垃圾生物有机肥和短期（1 a）施用大量餐厨垃圾生物有机肥4种施肥方式,分别记为CK组、CF组、LOF-5组和MOF-1组,对比分析不同施肥方式对土壤OM（有机质）、活性有机碳、营养元素和团聚体等的影响.结果表明:①施用餐厨垃圾生物有机肥可显著提高土壤OM、活性有机碳含量,其中,MOF-1组提高效果最显著,与CK组相比,w（OM）可提高173.29%,w（ROC）（ROC为易氧化有机碳）增加了39.17%,w（POC）（POC为颗粒有机碳）和w（DOC）（DOC为可溶性有机碳）分别是CK组的13.85和10.32倍.②中长期（5 a）施用少量餐厨垃圾生物有机肥可增加土壤中较大粒径团聚体的占比,且更有利于提高土壤团粒结构的稳定性,LOF-5组>2 mm粒级的团聚体占比是CK组的4.68倍;与CK组相比,LOF-5组MWD（平均重量直径）增加了100.00%,GMD（几何平均直径）增加了82.98%,>0.25 mm水稳定性团聚体质量占比（DR_0.25）增加了27.20%.③中长期（5 a）施用少量餐厨垃圾生物有机肥可增加土壤中w（TN）（TN为全氮）和w（AN）（AN为速效氮）,与CK组相比,LOF-5组w（TN）和w（AN）分别增加了77.42%和20.82%.施用餐厨垃圾有机肥也可同时增加土壤中w（AP）（AP为速效磷）和w（AK）（AK为速效钾）,MOF-1组增加效果较佳,w（AP）和w（AK）分别是CK组的9.43和3.39倍.研究显示,中长期（5 a）施用少量餐厨垃圾生物有机肥可提升土壤固碳能力,提高土壤养分利用的有效性,从而提升耕地土壤质量,减少化肥施用量,是我国贫瘠黄褐土改良的有效施肥模式.