The effects of sulphur gas and elemental sulphur dust deposition on Pinus contorta x Pinus banksiana: cell walls and water relations

The bulk modulus of elasticity (E) for Pinus contorta (lodgepole pine) x Pinus banksiana (jack pine) hybrids was compared between a site (AI) close to a sour gas processing plant and a control site (AV). The mean bulk modulus of elasticity for branches from AI was 47.5 MPa vs 18.5 MPa for the control site (AV). Site AI had been exposed to S-gas emissions and large amounts of elemental S deposition and had an acidic soil (pH 4.0 at 10 cm depth). During 1981 the needles at AI had more aluminum and iron compared to those at AV (900 ppm vs 390 ppm AI in the 3-year-old needles). Mean leader growth was measured over a 3-year period and was observed to be greater at AI than AV (46+/-7 cm vs 29+/-9 cm for 1988). Histochemically, the needles at AI had higher phenol and lignin content than AV. These results suggest that the S-gas fumigation, S-dust deposition, plus increased concentrations of soluble aluminum and iron had altered the cell wall elastic properties resulting in altered water relations. The implications of this on leaf diffusive resistance and photosynthesis are discussed.     

Sustainable green technology on wastewater treatment: The evaluation of enhanced single chambered up-flow membrane-less microbial fuel cell

This study demonstrated the potential of single chamber up-flow membrane-less microbial fuel cell(UFML-MFC) in wastewater treatment and power generation. The purpose of this study was to evaluate and enhance the performance under different operational conditions which affect the chemical oxygen demand(COD) reduction and power generation,including the increase of KCl concentration(MFC1) and COD concentration(MFC2). The results showed that the increase of KCl concentration is an important factor in up-flow membrane-less MFC to enhance the ease of electron transfer from anode to cathode. The increase of COD concentration in MFC2 could led to the drop of voltage output due to the prompt of biofilm growth in MFC2 cathode which could increase the internal resistance. It also showed that the COD concentration is a vital issue in up-flow membrane-less MFC.Despite the COD reduction was up to 96%, the power output remained constrained.     

DECISION SUPPORT FOR ALLOCATION OF WATERSHED POLLUTION LOAD USING GREY FUZZY MULTIOBJECTIVE PROGRAMMING1

ABSTRACT: This paper uses the grey fuzzy multiobjective programming to aid in decision making for the allocation of waste load in a river system under versatile uncertainties and risks. It differs from previous studies by considering a multicriteria objective function with combined grey and fuzzy messages under a cost benefit analysis framework. Such analysis technically integrates the prior information of water quality models, water quality standards, wastewater treatment costs, and potential benefits gained via in‐stream water quality improvement. While fuzzy sets are characterized based on semantic and cognitive vagueness in decision making, grey numbers can delineate measurement errors in data collection. By employing three distinct set theoretic fuzzy operators, the synergy of grey and fuzzy implications may smoothly characterize the prescribed management complexity. With the aid of genetic algorithm in the solution procedure, the modeling outputs contribute to the development of an effective waste load allocation and reduction scheme for tributaries in this subwatershed located in the lower Tseng‐Wen River Basin, South Taiwan. Research findings indicate that the inclusion of three fuzzy set theoretic operators in decision analysis may delineate different tradeoffs in decision making due to varying changes, transformations, and movements of waste load in association with land use pattern within the watershed.     

Sensitivity analysis of ground-level ozone concentration to emission changes in two urban regions of southeast Texas

Air pollutant emission is one of the predominant factors affecting urban air quality such as ground-level ozone formation. This paper assesses the impact of changing emission inventory scenarios, based on combinations of point, mobile, area/non-road and biogenic sources, on the tropospheric ozone concentration in two southeast Texas urban areas, i.e. Houston-Galveston and Beaumont-Port Arthur, during the rapid ozone formation event (ROFE) on August 25, 2000. The EPA's Community Multiscale Air Quality (CMAQ) modeling system with 1999 national emission inventory (NEI99) estimates and updated SAPRC99 chemical mechanism are used in the sensitivity analysis for twelve different emission scenarios. Based on model results, it is found that the point source emission of NOx and VOC contributes the greatest ozone peak in the ROFE. Removing Texas point sources of VOC and NOx emission from the inventory results in a reduction in peak O3 concentration by 128 and 70 ppbv in Houston urban area, respectively. Similar but less drastic impact from point source is also observed in the Beaumont-Port Arthur area. The effect on peak ozone concentration due to mobile, area and non-road sources emissions are less significant compared to that of point source emission. Reducing VOC emission appears to be more effective than reducing NOx emission in lowering peak O3 concentration in the studied region. Although biogenic emission can contribute up to 37 ppbv of peak ozone level over a large area, the affected area is away from the urban region of concern, and should not be the main cause for O3 non-attainment in the two urban areas. Removing CO emission from mobile sources does not lead to significant reduction (< 1 ppbv) in ozone concentrations. The modeled data also show that the transport of O3 precursors from adjacent states can cause a significant ozone plume near Beaumont due to its proximity to the state border based on the conditions during the August 25, 2000 O3 episode.     

Importance and uncertainty analysis of flue gas scrubber systems with extreme reliability parameter values

Although reliability analyses have been used to improve the reliability of industrial systems, generic reliability data from publications, such as component failure intensities and repair times, are used to calculate reliability measures instead of the real reliability data collected from the plant. One reason is that the repair history of the components is not well managed in the plant. In this work, the effect of extreme reliability parameter values on system reliability and unavailability is studied. To do this, importance and uncertainty analysis of the components of flue gas scrubber systems is carried out, and results calculated with the extreme reliability parameter values are compared with those with the mean reliability values of the systems. The different reliability parameter values can give us totally different ranks of the components critical to the reliability of the representative scrubber system. Consequently, the effort to establish a reliable database is emphasized to perform accurate reliability analysis of the system.     

Application of fluidized bed combustion to industrial waste treatment

Landfill and sea-dumping appear to be on their way out as acceptable methods for the disposal of untreated industrial wastes in Taiwan. Recently, there has been interest in the application of fluidized bed technology to waste incineration for efficient energy utilization and environmental protection. A pilot fluidized bed combustion system was used to investigate the incineration performance and parametric test for the waste from an industrial park. According to the experimental results, the appropriate operating conditions, including temperatures of 800-840 degrees C, aeration rates of U(0)/Um(f)-2.0 or so, and on-bed feeding, were recommended to treat such waste. The emissions of SO(x), NO(x) and CO in flue gas meet the ROC-EPA regulation.