Utilization of MSWI fly ash as partial cement or sand substitute with focus on cementing efficiency and health risk assessment

• Washed MSWI fly ash was used as partial cement or sand substitute. • Sand replacing is beneficial for strength, while cement replacement reduces strength. • Cementing efficiency factor and mortar pore structure explain the strength results. • Health risk assessment was conducted for MSWI fly ash blended cement mortar. • CR and HI contributed by different exposures and heavy metals were analyzed. The strength of cement substituted mortar decreases with the increase in fly ash amount, whereas the strength increases when the fly ash is blended as sand substitute. A mortar with highest strength (compressive strength= 30.2 Mpa; flexural strength= 7.0 Mpa) was obtained when the sand replacement ratio was 0.75%. The k value (cementing efficiency) of fly ash varied between 0.36 and 0.15 for the fly ash fraction in binder between 5% and 25%. The k values of fly ash used for sand replacement were all significantly above that used for cement substitution. The macropores assigned to the gaps between particles decreased when the fly ash was used as sand replacement, providing an explanation for the strength enhancement. The waste-extraction procedure (toxicity-sulphuric acid and nitric acid method (HJ/T 299-2007)) was used to evaluate metal leaching, indicating the reuse possibility of fly ash blended mortar. For the mortar with the mass ratio of fly ash to binder of 0.5%, the carcinogenic risks (CR) and non-carcinogenic hazard quotient (HQ) in sensitive scenario for blended mortar utilization were 9.66 × 10^-7 and 0.06, respectively; these results were both lower than the threshold values, showing an acceptable health risk. The CR (9.89 × 10^-5) and HQ (3.89) of the non-sensitive scenario for fly ash treatment exceeded the acceptable threshold values, indicating health risks to onsite workers. The main contributor to the carcinogenic and non-carcinogenic risk is Cr and Cd, respectively. The CR and HQ from inhalation was the main route of heavy metal exposure.     

Biological conversion pathways of sulfate reduction ammonium oxidation in anammox consortia

• The SRAO phenomena tended to occur only under certain conditions. • High amount of biomass and non-anaerobic condition is requirement for SRAO. • Anammox bacteria cannot oxidize ammonium with sulfate as electron acceptor. • AOB and AnAOB are mainly responsible for ammonium conversion. • Heterotrophic sulfate reduction mainly contributed to sulfate conversion. For over two decades, sulfate reduction with ammonium oxidation (SRAO) had been reported from laboratory experiments. SRAO was considered an autotrophic process mediated by anammox bacteria, in which ammonium as electron donor was oxidized by the electron acceptor sulfate. This process had been attributed to observed transformations of nitrogenous and sulfurous compounds in natural environments. Results obtained differed largely for the conversion mole ratios (ammonium/sulfate), and even the intermediate and final products of sulfate reduction. Thus, the hypothesis of biological conversion pathways of ammonium and sulfate in anammox consortia is implausible. In this study, continuous reactor experiments (with working volume of 3.8L) and batch tests were conducted under normal anaerobic (0.2≤DO<0.5 mg/L) / strict anaerobic (DO<0.2 mg/L) conditions with different biomass proportions to verify the SRAO phenomena and identify possible pathways behind substrate conversion. Key findings were that SRAO occurred only in cases of high amounts of inoculant biomass under normal anaerobic condition, while absent under strict anaerobic conditions for same anammox consortia. Mass balance and stoichiometry were checked based on experimental results and the thermodynamics proposed by previous studies were critically discussed. Thus anammox bacteria do not possess the ability to oxidize ammonium with sulfate as electron acceptor and the assumed SRAO could, in fact, be a combination of aerobic ammonium oxidation, anammox and heterotrophic sulfate reduction processes.     

A review of measurement methods for peracetic acid (PAA)

• Physical and chemical properties and application of peracetic acid solution. • Determination method of high concentration peracetic acid. • Determination method of residual peracetic acid (low concentration). Peroxyacetic acid has been widely used in food, medical, and synthetic chemical fields for the past several decades. Recently, peroxyacetic acid has gradually become an effective alternative disinfectant in wastewater disinfection and has strong redox capacity for removing micro-pollutants from drinking water. However, commercial peroxyacetic acid solutions are primarily multi-component mixtures of peroxyacetic acid, acetic acid, hydrogen peroxide, and water. During the process of water treatment, peroxyacetic acid and hydrogen peroxide (H₂O₂) often coexist, which limits further investigation on the properties of peroxyacetic acid. Therefore, analytical methods need to achieve a certain level of selectivity, particularly when peroxyacetic acid and hydrogen peroxide coexist. This review summarizes the measurement and detection methods of peroxyacetic acid, comparing the principle, adaptability, and relative merits of these methods.     

Compartmentation and effects of lead (Pb) in the collembolan,Folsomia candida

Environmental Science and Pollution Research - The impact of soil lead (Pb) pollution on survival, growth, and reproduction of the collembolan, Folsomia candida, and Pb compartmentation in its gut...     

Evaluating provincial eco-efficiency in China: an improved network data envelopment analysis model with undesirable output

Environmental Science and Pollution Research - In this study, an improved matrix-type network data envelopment analysis (NDEA) model with undesirable output was developed to evaluate the...     

Functional wastepaper-montmorillonite composite aerogel for Cd2+ adsorption

Environmental Science and Pollution Research - In this study, a composite aerogel (WP-MMT) composed of wastepaper (WP) and montmorillonite (MMT) was prepared by ambient pressure drying technology...     

N2O profiles in the enhanced CANON process via long-term N2H4 addition: minimized N2O production and the influence of exogenous N2H4 on N2O sources

Environmental Science and Pollution Research - Production of the greenhouse gas nitrous oxide (N2O) from the completely autotrophic nitrogen removal over nitrite (CANON) process is of growing...     

CO2资源化利用的现状及前景

介绍了CO2分离捕集最新工艺——电化学法、膜法、化学循环燃烧法的研究进展。评述分析了CO2的各种资源化应用前景：CO2气体用作生物碳源、辅助注射成型剂及有机物（如氨基甲酸酯、表面活性剂）合成原料等;液态CO2用于人造金刚石、热泵干燥、超临界CO2萃取及固体干冰冷喷射清洗等。CO2作为一种潜在的丰富碳源,应不断研发其新的应用领域,加快其工业化应用。     

土壤渗滤处理系统运行控制的模拟研究

通过建立地下水数学模型,回答了土壤渗滤工程运行控制中的两个难点问题:(1)工程运行水力负荷.当工程地块周边存在河流时,河流水位低时,有助于增加水力负荷,反之则降低水力负荷;实际土壤运行面积的增加和独立运行单元之间的间距增加也能够增加工程运行水力负荷.(2)地下水水质监测井的优化布设.模拟工程运行后地下水水质空间分布特征,在地下水水质最不利的位置和其他特别关注的位置布置监测井,从而能够以具有典型代表性且数目较少的监测井达到准确评估工程对地下水水质影响的目的.     

流化催化裂化烟气脱硫助剂的制备及其脱硫活性

采用溶胶-凝胶法制备锌铝助剂,该助剂于700℃焙烧后与流化催化裂化（FCC）催化剂进行机械混合,制得混合催化剂;在FCC烟气工业模拟装置上考察混合催化剂的脱硫活性,用混合催化剂的脱硫活性来反映锌铝助剂的脱硫性能。实验结果表明,氧化锌质量分数为10％的锌铝助剂的脱硫活性最佳,脱硫率达62．5％。采用红外光谱和X射线衍射（XRD）对锌铝助剂的脱硫机理进行了研究,红外分析结果表明,弱的L酸中心有利于锌铝助剂脱硫,XRD分析结果表明,锌铝助剂在锌铝尖晶石结构尚未完全形成时,存在较多的晶格缺陷,能够有效地吸附烟气中的SOx,将其转化为H2S。