Organophosphate flame retardants and plasticisers in wastewater treatment plants

Previous studies have revealed that chlorinated and non-chlorinated organophosphorous flame retardants and plasticisers are important contaminants in German surface waters and it has been demonstrated that wastewater treatment plants contribute to the emission of these substances. In this study temporal development as well as elimination efficiency were determined in two wastewater treatment plants (STP) in the Ruhr/Rhine area at different stages of the wastewater treatment process. The samples were analysed for the non-chlorinated organophosphate esters tri-n-butylphosphate (TnBP), tri-iso-butylphosphate (TiBP), tris-(butoxyethyl)-phosphate (TBEP) and triphenylphosphate (TPP) and the chlorinated organophosphate esters tris-(2-chloro, 1-methylethyl)-phosphate (TCPP), tris-(2-chloro-, 1-chloromethylethyl)-phosphate (TDCP) and tris-(2-chloroethyl)-phosphate (TCEP). The study showed that there were significant differences in the elimination of chlorinated and non-chlorinated organophosphorous flame retardants. The elimination rates ranged from 57-86% for TiBP, TnBP and TBEP at both STP's. No elimination of the chlorinated flame retardants TCPP, TDCP and TCEP was observed in any of the sampled STPs. At both STPs the first treatment steps and the final filtration did not contribute to the elimination of the non-chlorinated organophosphorous flame retardants while the aeration step did. At both STPs the efficiency of the cleaning process concerning the flame retardants was comparable. Thus the type of construction of the STP was not relevant for the elimination of these substances. Additionally a strong day-to-day variation was observed, while in one STP a temporal trend for TCPP during the week was found.     

High frequency monitoring of the coastal marine environment using the MAREL buoy

The MAREL Iroise data buoy provides physico-chemical measurements acquired in surface marine water in continuous and autonomous mode. The water is pumped 1.5 m from below the surface through a sampling pipe and flows through the measuring cell located in the floating structure. Technological innovations implemented inside the measuring cell atop the buoy allow a continuous cleaning of the sensor, while injection of chloride ions into the circuit prevents biological fouling. Specific sensors for temperature, salinity, oxygen and fluorescence investigated in this paper have been evaluated to guarantee measurement precision over a 3 month period. A bi-directional link under Internet TCP-IP protocols is used for data, alarms and remote-control transmissions with the land-based data centre. Herein, we present a 29 month record for 4 parameters measured using a MAREL buoy moored in a coastal environment (Iroise Sea, Brest, France). The accuracy of the data provided by the buoy is assessed by comparison with measurements of sea water weekly sampled at the same site as part of SOMLIT (Service d'Observation du Milieu LIToral), the French network for monitoring of the coastal environment. Some particular events (impact of intensive fresh water discharges, dynamics of a fast phytoplankton bloom) are also presented, demonstrating the worth of monitoring a highly variable environment with a high frequency continuous reliable system.     

Development and validation of methods for environmental monitoring of cyclophosphamide in workplaces

Methods to monitor contamination of workplaces with antineoplastic drugs have been developed and validated. Cyclophosphamide (CP) was used as a model compound as it is one of the most commonly used antineoplastic drugs. A wipe sampling method to detect contamination with CP at surfaces was developed. A personal air sampling method to sample gas and vapour on solid sorbent tubes and particles with filters was also developed. Wipe and filter samples were extracted and sorbent samples were eluted, all with ethyl acetate. The samples were analysed with liquid chromatography tandem mass spectrometry. (2)H(6)-labelled cyclophosphamide was used as an internal standard. The between-day precision was 2-5% for wipe samples, 4-6% for sorbent samples and 3-8% for filter samples. The limit of detection was 0.02 ng CP per sample for the wipe and filter methods and 0.03 ng CP per sample for the solid sorbent method. Wipe sampling on surfaces made of different materials resulted in mean recoveries between 78-106%. The desorption recovery was between 97-102% for the wipe samples, 97% for the sorbent samples and 101% for the filter samples. Samples were stable for up to 2 months at 5 degrees C and -20 degrees C and for about 2 d at room temperature. The developed methods were applied to the measurement of contamination with CP in a hospital pharmacy. Trace amounts of CP, 1.3 and 1.4 ng, were detected on surfaces in the pharmacy.     

Dioxin-like compounds in pine needles around Tokyo Bay, Japan in 1999

Pine needle samples collected at ten spatially distant sites around Tokyo Bay in 1999 indicated a widespread lower troposphere pollution with ultra-trace dioxin-like compounds such as chlorodibenzo-p-dioxins (PCDDs), -furans (PCDFs), non-ortho- and mono-ortho-chlorobiphenyls (pPCBs), and -naphthalenes (PCNs). Elevated concentration of planar PCBs and the total PCNs were found at the sites which are located innermost to the Bay, suggesting the regional importance of the evaporative nature of the source of pollution by those compounds over this vast area. The concentrations and profiles for PCDDs and PCDFs remained largely uniform. An exception was the site near the town of Tateyama in the Chiba Prefecture, which is the southernmost but also relatively separate from the inner Bay. The site near Tateyama showed somehow background contamination with all compound groups and highly different profiles of PCNs. The principal component analysis (PCA) of the data matrix has revealed that around the Tokyo Bay, apart from the evaporative emission sources for PCNs and PCBs, combustion related processes also play an important role as sources of the ambient air contamination not only with PCDDs/Fs but also with chloronaphthalenes and planar chlorobiphenyls.     

A combination of micro-porous membrane liquid-gas extraction and solid-phase trapping for ultra trace determination of benzene in urine

A method was developed for the determination of benzene in urine. The sample was pumped through the donor channel of a membrane extraction unit with a micro-porous membrane, separating the donor channel from an identical acceptor channel purged with nitrogen. The analyte reached the acceptor channel by diffusion through the membrane and was then swept by the carrier to a solid sorbent tube, where it was trapped. The analyte was subsequently thermally desorbed and analyzed by gas chromatography (GC) with mass selective detection (MS). After optimization, the recovery was close to quantitative, or 95%. Purging the membrane unit with pure water in between the samples eliminated any memory effects. The linearity was good in the concentration range examined (20-4000 ng l(-1)), with a correlation coefficient of 0.9996. The repeatability at 50 ng l(-1) and 400 ng l(-1) was 1.4% and 1.2%, respectively. The limit of detection was 12 ng l(-1) and the limit of quantification 35 ng l(-1). This enables assessment of benzene exposures of occupationally exposed subjects, of smokers and the majority of the general population. The developed method can be easily automated.     

Evaluation of forest nutrition based on large-scale foliar surveys: are nutrition profiles the way of the future?

This paper introduces the use of nutrition profiles as a first step in the development of a concept that is suitable for evaluating forest nutrition on the basis of large-scale foliar surveys. Nutrition profiles of a tree or stand were defined as the nutrient status, which accounts for all element concentrations, contents and interactions between two or more elements. Therefore a nutrition profile overcomes the shortcomings associated with the commonly used concepts for evaluating forest nutrition. Nutrition profiles can be calculated by means of a neural network, i.e. a self-organizing map, and an agglomerative clustering algorithm with pruning. As an example, nutrition profiles were calculated to describe the temporal variation in the mineral composition of Scots pine and Norway spruce needles in Finland between 1987 and 2000. The temporal trends in the frequency distribution of the nutrition profiles of Scots pine indicated that, between 1987 and 2000, the N, S, P, K, Ca, Mg and Al decreased, whereas the needle mass (NM) increased or remained unchanged. As there were no temporal trends in the frequency distribution of the nutrition profiles of Norway spruce, the mineral composition of the needles of Norway spruce needles subsequently did not change. Interpretation of the (lack of) temporal trends was outside the scope of this example. However, nutrition profiles prove to be a new and better concept for the evaluation of the mineral composition of large-scale surveys only when a biological interpretation of the nutrition profiles can be provided.     

COMBUSTIVE APPROACH FOR MEASURING TOTAL VOLATILE PHOSPHORUS CONTENT IN LANDFILL GAS

A technique was developed to measure the total gaseous phosphorus content in biogas. The amount of air needed for a neutral to oxidising flame was mixed with the biogas. The gas mixture was burnt in a closed quartz burner and the combustion gasses were bubbled through a nitric acid solution. The phosphate content in the bubbling liquid was determined with sector field ICP-MS. The technique was validated in the lab with phosphine. Afterwards the set-up was installed on a landfill. The total gaseous phosphorus content in the landfill gas, measured with the combustive technique, ranged from 1.65 to 4.44 g P/m³. At the same time the phosphine concentration in the landfill gas was determined gas chromatographically (GC). The phosphine (PH₃) content measured with GC ranged from 7.6 to 16.7 g PH₃-P/m³. Since the phosphine-P content (GC) was consistently higher than the total gaseous phosphorus content (burner/ICP-MS), the hypothesised presence of highly toxic gaseous phosphorus compounds other than phosphine could not be demonstrated.     

Distribution of Iron, Manganese, Zinc and Atrazine in Groundwater in Parts of Palar and Cheyyar River Basins, South India

A study was carried out in a part of Palar and Cheyyar river basin to evaluate the current status of iron, manganese, zinc and atrazine concentrations, their origin and distribution in groundwater. Groundwater samples were collected during post-monsoon (March 1998 and February 1999) and pre-monsoon (June 1999) periods from 41 sampling wells distributed throughout the study area. The groundwater samples were analyzed for trace metals using AAS and atrazine using HPLC. The concentration of the trace elements in groundwater is predominant during pre-monsoon period. Distribution pattern indicates that the concentration of these elements increases from west to northeast and towards Palar river. Lower concentrations in the central part may be due to recharge of fresh water from the lakes located here. During most of the months, as there is no flow in Palar river, the concentrations of trace elements in groundwater are high. Drinking water standards indicate that Mn and Zn cross the permissible limit recommended by EPA during the pre-monsoon period. A comparison of groundwater data with trace element chemistry of rock samples shows the abundance of trace elements both in the rock and water in the order of Fe > Mn > Zn and Fe > Zn > Mn. This indicates that iron in groundwater is derived from lithogenic origin. Further, Fe, Mn and Zn have good correlation in rock samples, while it is reverse in the case of water samples, indicating the non-lithogenic origin of Mn and Zn. Atrazine (a herbicide) was not detected in any of the groundwater samples in the study area, perhaps due to low-application rate and adsorption in the soil materials.     

Monitoring of Butter and Ghee (Clarified Butter Fat) for Pesticidal Contamination from Cotton Belt of Haryana, India

Butter (45) and ghee (55) samples were collected from rural and urban areas of cotton growing belt of Haryana and analysed for detecting the residues of organochlorine, synthetic pyrethroid and organophosphate insecticides. The estimation was carried out by using multi residue analytical technique employing GC-ECD and GC-NPD systems equipped with capillary columns. Butter samples were comparatively more contaminated (97%) than ghee (94%), showing more contamination with organochlorine insecticides from urban samples. About 11% samples of butter showed endosulfan residues above MRL value and 2% samples had residues of synthetic pyrethroids and organophosphates each above their respective MRL values. In ghee, residues of HCH & DDT both and of endosulfan exceeded the MRL values in 5 and 20% samples, respectively. Among organophosphates, only chlorpyriphos was detected with 9% samples showing its residue above MRL value. Irrespective of contamination levels, residues above the MRL values were more in ghee. More extensive study covering other agricultural regions/zones of Haryana has been suggested to know the overall scenario of contamination of milk products.     

Sulphate, Nitrogen and Base Cation Budgets at 21 Forested Catchments in Canada, the United States and Europe

To assess the concern over declining base cation levels in forest soils caused by acid deposition, input-output budgets (1990s average) for sulphate (SO₄), inorganic nitrogen (NO₃-N; NH₄-N), calcium (Ca), magnesium (Mg) and potassium (K) were synthesised for 21 forested catchments from 17 regions in Canada, the United States and Europe. Trend analysis was conducted on monthly ion concentrations in deposition and runoff when more than 9 years of data were available (14 regions, 17 sites). Annual average SO₄ deposition during the 1990s ranged between 7.3 and 28.4 kg ha⁻¹ per year, and inorganic nitrogen (N) deposition was between 2.8 and 13.8 kg ha⁻¹ per year, of which 41–67% was nitrate (NO₃-N). Over the period of record, SO₄ concentration in deposition decreased in 13/14 (13 out of 14 total) regions and SO₄ in runoff decreased at 14/17 catchments. In contrast, NO₃-N concentrations in deposition decreased in only 1/14 regions, while NH₄-N concentration patterns varied; increasing at 3/14 regions and decreasing at 2/14 regions. Nitrate concentrations in runoff decreased at 4/17 catchments and increased at only 1 site, whereas runoff levels of NH₄-N increased at 5/17 catchments. Decreasing trends in deposition were also recorded for Ca, Mg, and K at many of the catchments and on an equivalent basis, accounted for up to 131% (median 22%) of the decrease in acid anion deposition. Base cation concentrations in streams generally declined over time, with significant decreases in Ca, Mg and K occurring at 8, 9 and 7 of 17 sites respectively, which accounted for up to 133% (median 48%) of the decrease in acid anion concentration. Sulphate export exceeded input at 18/21 catchments, likely due to dry deposition and/or internal sources. The majority of N in deposition (31–100%; median 94%) was retained in the catchments, although there was a tendency for greater NO₃-N leaching at sites receiving higher (<7 kg ha^-1 per year) bulk inorganic N deposition. Mass balance calculations show that export of Ca and Mg in runoff exceeds input at all 21 catchments, but K export only exceeds input at 16/21 sites. Estimates of base cation weathering were available for 18 sites. When included in the mass balance calculation, Ca, Mg and K exports exceeded inputs at 14, 10 and 2 sites respectively. Annual Ca and Mg losses represent appreciable proportions of the current exchangeable soil Ca and Mg pools, although losses at some of the sites likely occur from weathering reactions beneath the rooting zone and there is considerable uncertainty associated with mineral weathering estimates. Critical loads for sulphur (S) and N, using a critical base cation to aluminium ratio of 10 in soil solution, are currently exceeded at 7 of the 18 sites with base cation weathering estimates. Despite reductions in SO₄ and H⁺ deposition, mass balance estimates indicate that acid deposition continues to acidify soils in many regions with losses of Ca and Mg of primary concern. The U.S. Government's right to retain a non-exclusive, royalty free licence in and to any copyright is acknowledged. The Canadian Crown reserves the right to retain a non-exclusive, royalty free licence in and to any copyright.