Real-time discharge measurement in tidal streams by an index velocity

Discharge measurement in a tidal stream is always a difficult task. Owing to the complex flow conditions, discharge measurement in tidal streams has to be finished quickly, and must be highly efficient in order to yield an accurate measurement of real-time discharge. Measuring the discharge of tidal streams is done in three steps: (1) establishing the stage and cross-sectional area relation, (2) estimating the index velocity by using a velocity distribution equation based on the probability concept, (3) establishing the relationship between the index and mean velocities. Then the cross-sectional area and mean velocity can be estimated by the gage height and index velocity, respectively. The discharge of tidal streams is computed as the product of the cross-sectional area and mean velocity. The velocity distribution of the Taipei Bridge and Guan-du Bridge in the Tanshui River were established and analyzed to demonstrate the use of discharge measurement by index velocity for estimating the discharge of this tidal stream. The results reveal no large difference between the discharges measured by the conventional methods and the index velocity. This pilot study proposed a cost-effectiveness and efficient method. It is an easy, quick, and accurate model for measuring the real-time discharge of a tidal stream. It makes automatic, real-time, and continuous monitoring of the discharge in a tidal stream become possible.     

Characteristic, composition, and sources of TSP investigated by HRTEM/EDS and ESEM/EDS

Total suspended particle (TSP) collected at the fifth floor of House Dust in Hunan University, China, was analyzed in terms of microscopic morphology and chemical composition. The fine particles (50?nm-2?μm) in the TSP were analyzed by a high-resolution transmission electron microscope equipped with an energy-dispersive X-ray analyzer (HRTEM/EDS). Results showed that the particles were in shapes of plate, irregular and agglomerate. Based on EDS results, these fine particulate matter was primarily composed of Fe-rich (35.82-61.29%), Ca-rich (30.18-36.77%) and Si-rich (18.95-32.28%) particles. Other elements mainly including Mg (0.47-4.97%), Al (0.45-14.57%), S (0.45-4.73%), K (1.13-2.13%) and Zn (0.67-3.85%) were also observed. The sources analysis indicated that the HRTEM particles mainly originated from coal combustion, traffic emission, vehicles exhaust emission and fugitive soil or cement particulate matter. The coarse particles (4-50?μm) were detected by environmental scanning electron microscopy coupled with energy-dispersive X-ray detector (ESEM/EDS). Based on a simple algorithm, ESEM particles were categorized into five groups: C-bearing (46.15%, 67% and 86.98%), Si + Ca-bearing (21.48?+?11.80%, 16.51?+?10.81% and 16.32?+?10.62%), Si + Al-bearing (20.06?+?12.40%, 20.16?+?11.22% and 15.31?+?11.25%), Si-bearing (34.40%, 26.92% and 27.15%) particles and aggregates, most of which exhibit obvious crystalline structure, and these ESEM particles mainly derived from vehicles exhaust emission, coal combustion, soil, and biomass burning, while the aggregates are indicative of atmospheric reaction progress. HRTEM/EDS and ESEM/EDS are mutual complementary in analyzing the characteristic and determining the sources of TSP.     

Characteristics and assessment of phthalate esters in urban dusts in Guangzhou city, China

Phthalate esters (PAEs) were examined in indoor and outdoor dust samples from the subtropical city of Guangzhou, China. The ∑(16)PAEs concentrations ranged from 121 to 3,223 μg g(-1) dust, with the median concentration of 840 μg g(-1) dust. Significantly higher concentrations of PAEs in dust samples were found in offices where electrical and electronic devices, carpet pads, and office furniture were widely used. Of the 16 PAEs, diisobutyl phthalate (DiBP), di-n-butyl phthalate (DnBP), and di(2-ethylhexyl) phthalate (DEHP) dominated the PAEs in indoor and outdoor dust samples, and accounted for >96.8% and >93.1% of the ∑(16)PAEs concentrations, respectively. The median daily inhalation exposure of ∑(16)PAEs were 3.53 and 0.247 μg kg(-1) body weight day(-1), and at the 95(th) percentile were 7.62 and 0.530 μg kg(-1) body weight day(-1), up on the measured concentrations and estimated dust ingestion rates, respectively, for toddles and adults. The ubiquitous distribution of PAEs as noted in this study suggests the need for detailed assessment of PAEs concentrations using more sites and to further investigate the factors influencing PAEs exposure in China.     

Chemical compositions and sources of atmospheric PM10 in heating, non-heating and sand periods at a coal-based city in northeastern China

Mass concentrations and chemical components (18 elements, 9 ions, organic carbon [OC] and elemental carbon [EC]) in atmospheric PM(10) were measured at five sites in Fushun during heating, non-heating and sand periods in 2006-2007. PM(10) mass concentrations varied from 62.0 to 226.3 μg m(-3), with 21% of the total samples' mass concentrations exceeding the Chinese national secondary standard value of 150 μg m(-3), mainly concentrated in heating and sand periods. Crustal elements, trace elements, water-soluble ions, OC and EC represented 20-47%, 2-9%, 13-34%, 15-34% and 13-25% of the particulate matter mass concentrations, respectively. OC and crustal elements exhibited the highest mass percentages, at 27-34% and 30-47% during heating and sand period. Local agricultural residuals burning may contribute to EC and ion concentrations, as shown by ion temporal variation and OC and EC correlation analysis. Heavy metals (Cr, Ni, Zn, Cu and Mn) from coal combustion and industrial processes should be paid attention to in heating and sand periods. The anion/cation ratios exhibited their highest values for the background site with the influence of stationary sources on its upper wind direction during the sand period. Secondary organic carbon were 1.6-21.7, 1.5-23.0, 0.4-17.0, 0.2-33.0 and 0.2-21.1 μg m(-3), accounting for 20-77%, 44-88%, 4-77%, 8-69% and 4-73% of OC for the five sampling sites ZQ, DZ, XH, WH and SK, respectively. From the temporal and spatial variation analysis of major species, coal combustion, agricultural residual burning and industrial emission including dust re-suspended from raw material storage piles were important sources for atmospheric PM(10) in Fushun at heating, non-heating and sand periods, respectively. It was confirmed by principal component analysis that coal combustion, vehicle emission, industrial activities, soil dust, cement and construction dust and biomass burning were the main sources for PM(10) in this coal-based city.     

Comparative assessments of VOC emission rates and associated health risks from wastewater treatment processes

With the growing concern regarding emission of volatile organic compounds (VOCs) from wastewater treatment plants (WWTPs), the relationship between the VOC emission rates and the associated public health risks has been rarely discussed. The objective of this study was to examine and compare the VOC emission rates and cancer and non-cancer risks by inhalation intake, using a municipal WWTP in China as an example, with respect to the effects of treatment technologies, VOC species, and seasonal variation. Given the treatment technology considered, the emission rates of VOCs in this study were estimated by means of mass balance or calculated on the molecular level. From the viewpoints of both emission rates and cancer and non-cancer risks, sedimentation was the treatment technology with the highest health risks to the workers. Slightly lower VOC emission rates and health risks than those for sedimentation were observed in anaerobic treatment. Although the aeration significantly enhanced the VOC emission rates in the aerobic treatment process, the associated health risks were limited due to the low VOC concentrations in the gas phase, which were likely attributed to the strong mixing and dilution with fresh air by aeration. Amongst the VOCs investigated, benzene was the VOC with both a relatively high emission rate and health risk, while trichloroethylene possessed a high emission rate but the lowest health risk. Without strong interfacial aeration and turbulence between the water and atmosphere, the effects of treatment technology and seasonal variation on the health risks might be connected to the VOC emission rates, while the effect of VOC species depended considerably on the respective cancer slope factors and reference concentrations; the employment of aeration provided a different conclusion in which the emission rates were enhanced without a significant increase in the related cancer risks. These findings can provide insight into future health risk management and reduction strategies for workers in WWTPs.     

Molecular detection and comparison of Acanthamoeba genotypes in different functions of watersheds in Taiwan

The protistan genus Acanthamoeba is a free-living amoeba existing in various environments. Within this protistan genus, there are some species recognized as potential human pathogens, which may cause granulomatous amoebic encephalitis, Acanthamoeba keratitis and chronic granulomatous lesions of the skin. In this study, 211 water samples were collected from two watersheds in southern Taiwan. We detected Acanthamoeba based on the PCR amplification with a genus-specific primer pair and investigation of Acanthamoeba in Puzih River and Kaoping River in southern Taiwan. Acanthamoeba species were detected in 34 (16.1%) samples. The presence or absence of Acanthamoeba within the water samples showed significant difference with the levels of water temperature and total coliforms. The most frequently identified Acanthamoeba genotype was T4 (n = 19), followed by T5 (n = 8), and then T15 (n = 3). Genotype T6, T7/T8, T11 and T12 were all detected once. Genotype T4, T5, T6, T11 and T15 of Acanthamoeba are responsible for Acanthamoeba keratitis and should be considered a potential health threat associated with human activities in environmental surface water watersheds.     

Some technical issues in managing PCBs

Polychlorinated biphenyls (PCBs) were important industrial chemicals featuring high thermal and chemical stability and low flammability. They were widely used as dielectric and thermal fluid in closed electro-technical applications (transformers, capacitors…) and also in numerous dispersive uses, ranking from auto-copying paper to sealant or coatings. During the 1960s, severe environmental consequences started becoming apparent. The stability of PCBs contributed to their persistence in the environment, their lipophilic character to bio-magnification. Fish-eating species seemed threatened in their existence. In Japan and in Taiwan, thousands of people consumed PCB-contaminated oil. The production of PCBs stopped completely during the 1980s. Usage could continue in closed applications only. In this paper, particular attention is given to two issues: the cleaning of PCB electric transformers and the potential impact of PCB-containing building materials. Other contributions will cover the management and treatment of PCB-contaminated soil, sludge or fly ash. The complete survey is being prepared by request of the Knowledge Center for Engineers and Professionals.     

Seasonal variation and spatial distribution of atmospheric mercury and its gas-particulate partition in the vicinity of a semiconductor manufacturing complex

This study investigated the tempospatial variation of atmospheric mercury and its gas-particulate partition in the vicinity of a semiconductor manufacturing complex, where a plenty of flat-monitor manufacturing plants using elemental mercury as a light-initiating medium to produce backlight fluorescence tubes and may fugitively emit mercury-containing air pollutants to the atmosphere. Atmospheric mercury speciation, concentration, and the partition of total gaseous mercury (TGM) and particulate mercury (Hg_p) were measured at four sites surrounding the semiconductor manufacturing intensive district/complex. One-year field measurement showed that the seasonal averaged concentrations of TGM and Hg_p were in the range of 3.30–6.89 and 0.06–0.14 ng/m³, respectively, whereas the highest 24-h TGM and Hg_p concentrations were 10.33 and 0.26 ng/m³, respectively. Atmospheric mercury apportioned as 92.59–99.01 % TGM and 0.99–7.41 % Hg_p. As a whole, the highest and lowest concentrations of TGM were observed in the winter and summer sampling periods, respectively, whereas the concentration of Hg_p did not vary much seasonally. The highest TGM concentrations were always observed at the downwind sites, indicating that the semiconductor manufacturing complex was a hot spot of mercury emission source, which caused severe atmospheric mercury contamination over the investigation region.     

Manganese concentrations in maternal–infant blood and birth weight

Manganese (Mn) is an essential mineral nutrient in mammals. The physiological role of Mn in animal models is well documented, but little is known about the adverse effects of Mn deficiency or overexposure in humans, including pregnancy outcomes such as birth weight. We examined the relationship of the maternal and cord blood Mn levels with birth weight in a cohort of 172 mother–infant pairs born in Shanghai, China. Non-linear spline and quadratic regression models were used to test the hypothesis of an inverted U-shaped association between the Mn levels and birth weight. The median (range) levels of Mn in the maternal and cord blood were 5.38 (2.34–30.37) μg/dL and 7.66 (2.57–34.23) μg/dL, respectively. An inverted U-shaped relationship was observed between maternal Mn and birth weight after adjusting for potential confounders. The birth weight increased with Mn levels up to 4.18 μg/dL, and a slight reduction in weight was observed at higher levels. The cord blood Mn levels were not found to be associated with birth weight. Both lower and higher Mn exposures are associated with lower birth weight, which may influence important developmental parameters; the association of higher Mn levels with lower weight was weak and imprecise.