As(V)在金红石TiO_2颗粒表面吸附特性及机理

通过静态动力学和热力学吸附实验,研究了温度、共存离子以及溶质的初始浓度对As(V)在金红石TiO2颗粒表面吸附的影响,探讨了As(V)在金红石TiO2颗粒表面吸附特性及机理。结果表明,在As(V)初始浓度为10 mg/L,pH为7的条件下,25℃时的吸附量0.41 mg/g高于30℃时的吸附量0.31 mg/g,As(V)在金红石TiO2上的吸附为放热过程。CaCl2和MgCl2的添加对As(V)在金红石TiO2表面吸附起到明显的促进作用。T=25℃,Ca2+或Mg2+浓度为10 mmol/L时,As(V)吸附量分别为0.64和0.56 mg/g,Ca2+比Mg2+对As(V)吸附促进作用强。As(V)在金红石TiO2的吸附等温线符合Frendlich方程,Lagergren二级动力学方程能较好地描述As(V)在金红石TiO2颗粒表面吸附的动力学过程。     

偶氮类染料脱色率的定量构效关系

偶氮类染料的生产和使用过程中存在着三废多、难脱色和污染严重等问题,该染料是印染工业的主要污染物。选取偶氮类染料的分子结构参数和其光催化氧化脱色率之间建立定量结构活性关系(QSAR),进而得到回归方程,为印染废水处理和染料环境行为评价提供理论预测。结果表明,偶氮类染料的光催化氧化脱色率与其结构之间存在着线性相关性,线性方程为:D=0.647μ+66.277,(D为脱色率、μ为偶极矩)R=0.989方程具有预测能力。     

镍基催化剂对污泥微波热解制生物气效能的影响

为实现污水污泥减量化、无害化及资源化的目标,在微波热解污水污泥基础上,进行了镍基催化剂对制取生物气效能影响的研究。采用元素分析对污泥元素进行检测,气/质联用分析(GC-MS)和气相色谱(GC)对热解生物气的组成和含量进行测定。实验结果表明,镍基催化剂的添加对微波热解污水污泥制取生物气有较大促进作用。5%添加量与800℃热解终温条件下具有最佳催化效果:生物气中H2、CO产量最大,H2产量由29 g/kg增加到35.8 g/kg,提升23.4%,CO产量由302.7 g/kg增加到383.3 g/kg,提升26.6%;同时催化剂还能提高热能利用效率,降低热解终温,即5%添加量在700℃热解终温时可达到空白800℃时的产气效果;镍基催化剂主要在500~600℃时发挥催化作用,加快了H2和CO的释放。微波热解污泥制取的生物气具有产量大、富含H2与CO等优点,可推动污水污泥的资源化进程。     

Adsorption of multi-heavy metals Zn and Cu onto surficial sediments: modeling and adsorption capacity analysis

Improved multiple regression adsorption models (IMRAMs) was developed to estimate the adsorption capacity of the components [Fe oxides (Fe), Mn oxides (Mn), organic materials (OMs), residuals] in surficial sediments for multi-heavy metal Zn and Cu. IMRAM is an improved version over MRAM, which introduces a computer program in the model developing process. As MRAM, Zn(Cu) IMRAM, and Cu(Zn) IMRAM again confirmed that there is significant interaction effects that control the adsorption of compounded Zn and Cu, which was neglected by additional adsorption model. The verification experiment shows that the relative deviation of the IMRAMs is less than 13 %. It is revealed by the IMRAMs that Mn, which has the greatest adsorption capability for compounded Zn and Cu (54.889 and 161.180 mg/l, respectively), follows by interference adsorption capacity of Fe/Mn (?1.072 and ?24.591 mg/l respectively). Zn and Cu influence each other through different mechanisms. When Zn is the adsorbate, compounded Cu mainly affects the adsorption capacities of Fe/Mn and Fe/Mn/OMs; while when Cu is the adsorbate, compounded Zn mainly exerts its effect on Mn, Fe/Mn, and Mn/OMs. It also shows that the compounded Zn or Cu weakened the interference adsorption of Fe/Mn, and meanwhile, strengthened the interference adsorption of Mn/OMs.     

Carbon Sequestration Function of Check-Dams: A Case Study of the Loess Plateau in China

Check-dams are the most common structures for controlling soil erosion in the Loess Plateau. However, the effect of check-dams on carbon sequestration, along with sediment transport and deposition, has not been assessed over large areas. In this study, we evaluated the carbon sequestration function of check-dams in the Loess Plateau. The results indicate that there were approximately 11 000 check-dams distributed in the Loess Plateau, with an estimate of the amount of sediment of 21 × 10⁹ m³ and a soil organic carbon storage amount of 0.945 Pg. Our study reveals that check-dams in the Loess Plateau not only conserve soil and water but also sequester carbon.     

基于白碳黑的水化硅酸钙制备及其磷回收特性简

以白碳黑、硅灰、硅藻土和硅胶筛选硅质原料,并与钙质原料电石渣制备了水化硅酸钙。借助XRF、BET、FTIR等表征手段,通过多次重复除磷实验,研究了硅质原料特性对水化硅酸钙回收磷性能的影响。结果表明,白碳黑具有极高的反应活性,因此可作为制备具有磷回收特性的水化硅酸钙的硅质原料。结合XRD等表征发现,白碳黑的有效利用率是影响水化硅酸钙回收磷性能的关键,该利用率取决于白碳黑与电石渣的摩尔配比以及水热反应温度。当电石渣与白碳黑的摩尔比为1.6：1,反应温度为170℃时,白碳黑具有最佳的利用效率。该条件制备的水化硅酸钙可作为晶种,在其表面结晶形成羟基磷灰石,从而达到磷回收的目的,磷回收后固体物质中的磷含量为19.05%。     

MCM-41介孔分子筛的合成及其对铜离子的吸附性能简

以微硅粉为硅源,CTAB和PEG-6000为模板剂,合成MCM-41介孔分子筛。采用XRD、N₂吸附-脱附曲线、FTIR以及TEM表征了其结构、比表面积、孔径分布及晶体形貌,并且以该样品为吸附剂,对含Cu²⁺的溶液进行了静态吸附实验。结果表明,以微硅粉为硅源成功合成了具有典型六方排列孔道结构的MCM-41,其比表面积为869.5 m²/g,孔容为0.97 cm³/g,平均孔径为3.3 nm;溶液pH为5~6时,MCM-41对Cu²⁺的去除效果最好;MCM-41对Cu²⁺的最大吸附吸附容量36.3 mg/g;MCM-41对Cu²⁺的吸附性能符合Langmuir吸附方程的特征。动力学研究表明,该过程符合准二级动力学模型。     

接种微生物与人粪便同步连续投加对好氧堆肥效果的影响简

利用新型梨形筒式好氧堆肥反应器,在通风量为3.0 L/min,搅拌频率为5 min/h的条件下,就不接种微生物、接种土著菌种、枯草芽孢杆菌与酵母菌时人粪便连续投加好氧堆肥效果进行了对比。堆制20 d即2个运行周期中各堆体的温度、含水率、COD、总氮、pH值与GI等的变化表明,接种微生物可以显著提高堆体的升温速率与堆体平均温度、COD降解率、GI（P<0.01）,堆肥可迅速达到完全腐熟。接种土著菌种效果最为明显（P<0.01）,其后相继为枯草芽孢杆菌与酵母菌。接种土著菌种可使堆体温度在50℃以上维持18 d,第8天COD降解率达到61.17%、总氮损失率为25.75%,第6天时GI达到108.22%。     

电镀污泥的热处理特性以及对金属回收的影响

焙烧-酸浸法可有效回收电镀污泥中的有价金属,而污泥的热处理特性是决定能否采用焙烧预处理的重要因素。研究了氧化焙烧和还原焙烧对污泥成分和金属浸出性的影响,并对焙烧前后的污泥进行了金属形态分析和X射线衍射(XRD)分析。结果表明,焙烧预处理实现了污泥减量和金属富集;ES1经氧化焙烧后金属浸出率接近原泥,Cu的浸出率达99%;ES2的还原焙烧效果优于氧化焙烧,特别是Cu的浸出率超过97%,XRD分析发现,还原焙烧过程中金属Cu被还原为铁铜合金;2种焙烧均造成了ES3中目标金属Ni的浸出率的降低;金属浸出性的下降与残渣态的形成有关。     

船舶塑料垃圾热解特性及动力学分析

利用热重分析(TGA)研究船舶塑料垃圾在不同升温速率和不同气氛下的热解特性,并得到了热解动力学参数。结果表明,船舶塑料垃圾的热解过程主要有3个阶段,比一般塑料热解复杂;随着升温速率增大,最大热解速率和最大热解速率温度等热解特性参数也增大,反应变得更剧烈;N2/CO2比为4∶1时,热解反应进行得最完全,固体残留率最少。动力学分析表明,采用3个连续一级反应模型能很好地拟合实验数据;不同的升温速率和气氛比对反应各阶段活化能均有不同程度的影响。