Profiles of enzymatic activity in earthworms from zinc, lead and cadmium polluted areas near Olkusz (Poland)

The aim of the study was to determine whether there are signs of adaptation of soil fauna to a gradient of heavy metal contamination. Earthworms Aporrectodea caliginosa, Lumbricus terrestris and Eisenia fetida were collected during the spring and summer of 2000 and 2001 from meadow sites situated between 2 and 32 km from the Bukowno-Olkusz complex of zinc-lead ore mines and smelters. The heavy metal content in the soil near smelters reaches 10,500 mg/kg (d.w.) for Zn, 2600 mg/kg for Pb and 81.9 mg/kg for Cd. The sites differ with respect to species composition of earthworm community, with A. caliginosa being dominant. Complete data was obtained only for A. caliginosa, since other species were not abundant at all investigated sites during the whole period of investigation. The body burdens of Zn, Pb, Cd and Cu in A. caliginosa reached 1500, 100, 220 and 10 microg/g, respectively, in the vicinity of the smelter (2-4 km), and decreased to 400, 2, 36 and 6 microg/g at the most distant site (32 km). Cadmium and lead content was significantly elevated in the whole body of L. terrestris collected at the site 2.5 km distant from the smelters when compared to more distant sites, while in E. fetida only the body burden of cadmium was elevated at the nearest site compared to the next site of transect. Activities of glutathione peroxidase (GPX; EC 1.11.1.9) against hydrogen peroxide (H2O2) or cumene hydroperoxide (cumOOH), glutathione reductase (GR; EC 1.6.4.2), glutathione S-transferase (GST; EC 2.5.1.18) and catalase (CAT; EC 1.11.1.6) were assayed in postmitochondrial supernatant obtained from whole body homogenates. Seasonal and annual variations of enzyme activity were reflected by higher GPX activity in the late summer of 2001 in comparison with the spring and summer of 2000. This may reflect severe drought in the spring and summer of 2000. The activity of both GPX isozymes, GR and GST in A. caliginosa and L. terrestris increased with increasing distance from the smelters and reached maximum at sites III and IV (4 and 8 km from the smelters, respectively) and then it decreased in the animals from site V (32 km). These may be the effects of antagonism between the enzyme inducing and enzyme inhibiting action of smelter emissions, a phenomenon known as a hormetic effect. It is postulated here that this effect is of diagnostic value for metal pollution biomonitoring.     

The use of ultra filtration in trace metal speciation studies in sea water

During this work, size fractionation technique "ultra filtration" is used in speciation studies of trace elements in the coastal sea water. Filtration is the most commonly used method to fractionate trace metal species, but often only "dissolved" and "particulate" fraction. The purpose of the present study is to determine colloidal and suspended particulate concentrations of Fe, Zn, Cu, Ni, and Mn in sea water. Suspended particulate matter were separated in three different size groups namely (>2.7 microm, <2.7->0.45 microm and <0.45->0.22 microm) by suction filtration using cellulose acetate and nitrate filter membranes. Thereafter to concentrate the solution with colloidal particle <0.22 microm-1.1 nm (0.5 k Nominal Molecular Weight cut-off Limit {NMWL}), the solution obtained from filtration through <0.22 microm, is sequentially passed through the ultra-filtration membranes having pore diameters of 14 nm (300 k NMWL), 3.1 nm (50 k NMWL), 2.2 nm (30 k NMWL), 1.6 nm (10 k NMWL) and 1.1 nm (0.5 k NMWL) by using Stirred Ultra-filtration Cells, operating in concentration mode. The concentration of Fe, Zn, Cu, Ni, and Mn were measured in suspended and dissolved fraction by ion chromatography, ICP-AES and Atomic Absorption Spectrometer. The salinity of the solution in various dissolved fractions of sequential filtration varies between 30.89-34.22 parts per thousand. The maximum concentrations of colloidal Zn, Cu, Ni and Mn in dissolved fraction were in <2.2->1.6 nm fraction. In case of Fe, colloidal fractions <2.2->1.6 nm and <1.6-<1.1 nm shows higher concentration. The concentration of Zn, Cu, Ni and Mn increase with decrease in size in suspended particulate matter, while the reverse is observed in case of Fe. This size separation data that specifies the partitioning of metals between dissolved and suspended solid phases is necessary for developing physically based models of metal transport in aquatic system.     

Household behaviour and attitudes with respect to recycling food waste--experiences from focus groups

It is a challenge to reduce the ever-increasing flow of waste. In Norway the systems for recycling of organic waste, paper, glass, metals, etc. differ between municipalities, both with regard to organizational and to technological structures. Our hypothesis is that people's attitudes and behaviour may differ with different systems of waste management. People's behaviour and attitudes regarding (organic) waste recycling were investigated in two municipalities with differing technical and organisational systems. Data came from interviews with municipal employees, questionnaires, focus groups and multi-criteria mapping. People seem to be better informed and more positive about organic waste recycling in one of the municipalities (MH, which has recycling of organic waste) than in the other (MS, which has no such recycling). The two municipalities had similar sets of important criteria for waste management (price, environmental friendliness, easy solutions, information). Many participants stated that they had learned from the group process, though only a few reported changed preferences. The institutional context seems to be important for people's behaviour and attitudes towards waste management. This implies that people's recycling behaviour does not only depend on technical and organisational aspects, but also on institutions. These are important messages for policy makers. On an individual basis, the different systems in the two municipalities seem to affect people's stated attitudes. These differences diminish when they are in a common setting where process and dialogue stimulate new thoughts and encourage people to act more altruistically.     

Global warming and environmental production efficiency ranking of the Kyoto Protocol nations

This paper analyzes the United Nations Organization's Kyoto Protocol nations to address two questions. First, what are the environmental production efficiency rankings of these nations? Second, is there a relationship between a nation's ratification status and its environmental production efficiency ranking? Our findings suggest that the nations that have ratified the Kyoto Protocol are more likely to be environmentally production efficient as compared to the nations that have not ratified the Protocol.     

Review of Agri-Environment Indexes and Stewardship Payments

Agri-environment programs aim to secure environmental and social stewardship services through payments to farmers. A critical component of many agri-environment programs is an agri-environment index (AEI) used to quantify benefits and target investments. An AEI will typically comprise multiple indicators, which are weighted and combined using a utility function, to measure the benefit of investment options (e.g., projects, farms, regions). This article presents a review of AEIs with 11 case studies from agri-environment programs in the United States, Australia, and the United Kingdom. We identify a generic procedure used to define AEIs and explore the implications of alternative methodological approaches. We conclude that AEIs have become an extremely important policy instrument and make suggestions for their improvement.     

A decision framework for possible remediation of contaminated sediments in the River Kymijoki, Finland

Background, aim, and scope  The paper describes the spatial contamination of the River Kymijoki, South-Eastern Finland, and the coastal region of the Gulf of Finland with PCDD/Fs and mercury. The findings of ecotoxicologial and human health studies are also reported, including environmental and human risk assessments. Sediments from the River Kymijoki, draining into the Gulf of Finland, have been heavily polluted by the pulp and paper industry and by chemical industries. A wood preservative, known as Ky-5, was manufactured in the upper reaches of the river between 1940 and 1984 causing severe pollution of river sediments with polychlorinated dibenzo-p-dioxins (PCDD) and dibenzofurans (PCDF). Moreover, the sediments have been polluted with mercury (Hg) from chlor-alkali production and the use of Hg as a slimicide in pulp and paper manufacturing. Materials and methods  An extensive sediment survey was conducted as well as sediment transport modeling, toxicity screening of sediment invertebrates, and a survey of contaminant bioaccumulation in invertebrates and fish. Studies on human exposure to PCDD/Fs and the possible effects on hypermineralization of teeth as well as an epidemiological study to reveal increased cancer risk were also conducted. An assessment of the ecological and human health risks with a null hypothesis (no remediation) was undertaken. Results  The sediment survey revealed severe contamination of river and coastal sediments with PCDD/Fs and Hg. The total volume of contaminated sediments was estimated to reach 5 × 10⁶ m³ and hot spots with extremely high concentrations (max 292,000 ng g⁻¹ or 1,060 ng I-TEQ g⁻¹ d.w.) were located immediately downstream from the pollution source (approximately 90,000 m³). Sediment contamination was accompanied by changes in benthic assemblages, but direct effects were masked by many factors. The fish showed only slightly elevated PCDD/F levels in muscle, but orders of magnitude higher in the liver compared with reference freshwater sites and the Baltic Sea. The concentrations in human fat did not reveal high human exposure in the Kymijoki area in general and was lower than in sea fishermen. The relative risk for total cancer among farmers was marginally higher (RR = 1.13) among those living close to the river, compared with farmers living further away, and the possibility of increased cancer risk cannot be ruled out. A conservative risk assessment revealed that the present probability of exceeding the WHO upper exposure limit of 4 pg WHO-TEQ kg⁻¹ d⁻¹ for PCDD/Fs and DL-PCBs was 6%. The probability of exceeding the WHO limit value of 0.23 μg kg⁻¹ d⁻¹ for methyl mercury was estimated to be notably higher at 62%. Based on these studies and the estimated risks connected with different remediation techniques a general remediation plan with cost benefit analysis was generated for several sub-regions in the river. Dredging, on-site treatment, and a close disposal of the most contaminated sediments (90,000 m³) was suggested as the first phase of the remediation. The decision regarding the start of remediation will be made during autumn 2008. Conclusions  The sediments in the River Kymijoki are heavily polluted with PCDD/Fs and mercury from earlier chlorophenol, chlor-alkali, and pulp and paper manufacturing. A continuous transport of contaminants is taking place to the Gulf of Finland in the Baltic Sea. The highly increased PCDD/F and Hg levels in river sediments pose an ecotoxicological risk to benthic fauna, to fish-eating predators and probably to human health. The risks posed by mercury exceed those from PCDD/Fs and need to be evaluated for (former) chlor-alkali sites and other mercury releasing industries as one basis for remediation decision making. Recommendations and perspectives  The studies form the basis of a risk management strategy and a plan for possible remediation of contaminated sediments currently under consideration in the Southeast Finland Regional Environment Centre. It is recommended that a detailed restoration plan for the most seriously contaminated areas should be undertaken. Based on current knowledge, the restoration of the whole river is not feasible, considering the current risk caused by the contaminated sediment in the river and the costs of an extensive restoration project. The experiences gained in the present case should be utilized in the evaluation of PCDD/F- and mercury-contaminated sites in other countries. The case demonstrates that the historic reservoirs are of contemporary relevance and should be addressed, e.g., in the national implementation plans of the Stockholm Convention. Electronic supplementary material  The online version of this article (doi:) contains supplementary material, which is available to authorized users.     

Post-fire seeding on Wyoming big sagebrush ecological sites: regression analyses of seeded nonnative and native species densities

Since the mid-1980s, sagebrush rangelands in the Great Basin of the United States have experienced more frequent and larger wildfires. These fires affect livestock forage, the sagebrush/grasses/forbs mosaic that is important for many wildlife species (e.g., the greater sage grouse (Centrocercus urophasianus)), post-fire flammability and fire frequency. When a sagebrush, especially a Wyoming big sagebrush (Artemisia tridentata ssp. wyomingensis (Beetle & A. Young)), dominated area largely devoid of herbaceous perennials burns, it often transitions to an annual dominated and highly flammable plant community that thereafter excludes sagebrush and native perennials. Considerable effort is devoted to revegetating rangeland following fire, but to date there has been very little analysis of the factors that lead to the success of this revegetation. This paper utilizes a revegetation monitoring dataset to examine the densities of three key types of vegetation, specifically nonnative seeded grasses, nonnative seeded forbs, and native Wyoming big sagebrush, at several points in time following seeding. We find that unlike forbs, increasing the seeding rates for grasses does not appear to increase their density (at least for the sites and seeding rates we examined). Also, seeding Wyoming big sagebrush increases its density with time since fire. Seeding of grasses and forbs is less successful at locations that were dominated primarily by annual grasses (cheatgrass (Bromus tectorum L.)), and devoid of shrubs, prior to wildfire. This supports the hypothesis of a "closing window of opportunity" for seeding at locations that burned sagebrush for the first time in recent history.     

Enrichment of the metallic components from waste printed circuit boards by a mechanical separation process using a stamp mill

Printed circuit boards incorporated in most electrical and electronic equipment contain valuable metals such as Cu, Ni, Au, Ag, Pd, Fe, Sn, and Pb. In order to employ a hydrometallurgical route for the recycling of valuable metals from printed circuit boards, a mechanical pre-treatment step is needed. In this study, the metallic components from waste printed circuit boards have been enriched using a mechanical separation process. Waste printed circuit boards shredded to <10mm were milled using a stamp mill to liberate the various metallic components, and then the milled printed circuit boards were classified into fractions of <0.6, 0.6-1.2, 1.2-2.5, 2.5-5.0, and >5.0mm. The fractions of milled printed circuit boards of size <5.0mm were separated into a light fraction of mostly non-metallic components and a heavy fraction of the metallic components by gravity separation using a zig-zag classifier. The >5.0mm fraction and the heavy fraction were subjected to two-step magnetic separation. Through the first magnetic separation at 700 Gauss, 83% of the nickel and iron, based on the whole printed circuit boards, was recovered in the magnetic fraction, and 92% of the copper was recovered in the non-magnetic fraction. The cumulative recovery of nickel-iron concentrate was increased by a second magnetic separation at 3000 Gauss, but the grade of the concentrate decreased remarkably from 76% to 56%. The cumulative recovery of copper concentrate decreased, but the grade increased slightly from 71.6% to 75.4%. This study has demonstrated the feasibility of the mechanical separation process consisting of milling/size classification/gravity separation/two-step magnetic separation for enriching metallic components such as Cu, Ni, Al, and Fe from waste printed circuit boards.     

Electrostatic separators of particles: Application to plastic/metal, metal/metal and plastic/plastic mixtures

Electrostatic separation is a generic term given to a significant class of technologies of industrial waste processing, widely used for the sorting of granular mixtures due to electric forces acting on particles whose average size is approximately 5mm. The focus of this paper is on three electrostatic processes of separation used for processing of different types of mixtures: (i) role-type electrostatic separator, used to sort mixtures containing metal/plastic particles (copper/PVC for example); (ii) plate-type electrostatic separator, used to sort mixtures containing metal/metal particles (copper/lead for example) and (iii) free-fall electrostatic separator, used to sort mixtures of plastic/plastic particles (PVC/PE for example). Experiments carried out on industrial samples using laboratory electrostatic separators confirm the efficiency of these processes and show that the processes can improve the recovery and purity of products resulting from industrial wastes.     

Estimation of mass transport parameters of gases for quantifying CH4 oxidation in landfill soil covers

Methane (CH(4)), which is one of the most abundant anthropogenic greenhouse gases, is produced from landfills. CH(4) is biologically oxidized to carbon dioxide, which has a lower global warming potential than methane, when it passes through a cover soil. In order to quantify the amount of CH(4) oxidized in a landfill cover soil, a soil column test, a diffusion cell test, and a mathematical model analysis were carried out. In the column test, maximum oxidation rates of CH(4) (V(max)) showed higher values in the upper part of the column than those in the lower part caused by the penetration of O(2) from the top. The organic matter content in the upper area was also higher due to the active microbial growth. The dispersion analysis results for O(2) and CH(4) in the column are counter-intuitive. As the upward flow rate of the landfill gas increased, the dispersion coefficient of CH(4) slightly increased, possibly due to the effect of mechanical dispersion. On the other hand, as the upward flow rate of the landfill gas increased, the dispersion coefficient of O(2) decreased. It is possible that the diffusion of gases in porous media is influenced by the counter-directional flow rate. Further analysis of other gases in the column, N(2) and CO(2), may be required to support this hypothesis, but in this paper we propose the possibility that the simulations using the diffusion coefficient of O(2) under the natural condition may overestimate the penetration of O(2) into the soil cover layer and consequently overestimate the oxidation of CH(4).