Observations of H2O2 and PAN in a rural atmosphere

Measurements of gaseous H2O2 and peroxyacetyl nitrate (PAN) concentrations in air are given for a site in rural southern England over an approximately 4-year period. In both cases the data show both diurnal and seasonal patterns. Temperature and wind direction had clear influences on the recorded concentrations of both species. There was an indication of increasing H2O2 concentrations with time. The use of a two-dimensional global model confirmed that this would be expected to occur alongside growth in ozone formation. It is suggested that, during photochemical episodes, the sequential build-up of ozone, PAN and H2O2 could be important in influencing the ability of vegetation to resist the effects of aggressive pollutants.     

An introduction to critical loads

The critical loads approach to emission controls of gaseous pollutants is a concept with a short but eventful history. Despite difficulties with definitions and agreed values, its acceptance within the UN-ECE Convention on Long Range Transboundary Air Pollution has provided the impetus for developing methods to put critical loads to a practical use-the revision of the UNECE emission protocols for sulphur and nitrogen. Methodologies first focus upon quantifying a pollutant threshold at which harmful effects occur on particular sensitive receptors (usually biological species). This threshold is known as the critical load for deposited pollutants, and as the critical level for gaseous pollutants acting on receptors. To calculate a critical load, biological effects are usually 'translated' to critical chemical values, e.g. harmful effects on fish 'translate' to alkalinity or aluminium concentrations in water; thus, critical load calculations may be based upon the chemistry of a system. Such calculations may be performed using simple, steady-state models, whilst the use of more complex, dynamic models provides an insight into the past and future trends. Maps of critical loads can be drawn using calculated values, and maps of pollutant deposition data will then show geographical areas where critical loads are exceeded. Spatial emission-deposition models can identify sources contributing to areas of excess loads and quantify necessary emission reductions. Optimization procedures applied to such models can derive abatement strategies related to economic costs and critical load effects. The critical load calculations may also be used to underpin the setting of target loads; these are pollutant loads, determined by political agreement, which take account of social, economic and political considerations.     

Deposition of ozone to a mature spruce forest: measurements and comparison to models

Removal of ozone at terrestrial surfaces provides a major sink for tropospheric ozone and, therefore, a constraint on the peak concentrations achieved during photochemical episodes. This study reports results from 5 years of almost continuous measurements of vertical profiles of ozone and related meteorological variables over a mature spruce forest in Bavaria. Deposition velocities calculated from flux/gradient and eddy correlation flux measurements have been compared with estimates based on a resistance model and yield satisfactory agreement during fine weather conditions. The results also suggest that biogenic emissions of reactive hydrocarbons from the forest influence the vertical profile of ozone.     

Trace metals in interstitial waters from sandstones: acidic inputs to shallow groundwaters

There is some evidence from southern Britain that shallow groundwaters in non-carbonate lithologies may be affected by acidic deposition. To investigate this, interstitial water profiles down to 12 m have been obtained from unsaturated sands or semi-consolidated sandstones from the Folkestone Beds (Lower Greensand) of Surrey and the Sherwood Sandstone of the West Midlands. The pH of the interstitial waters generally increased with depth and reflected an increase in the base saturation of the exchange complex. Beneath the highly acidic surface soil horizons (pH 3.0-3.5), interstitial waters with a pH of 4.0-4.5 were found down to depths of several metres. The pH progressively increased to around pH 5.5 because of base cation desorption and the weathering of silicate minerals. High concentrations of aluminium (10-20 mg litre(-1)) and other metals (Fe, Mn, Cu, Ni, Co, Zn, Be) were found in the interstitial water in the upper unsaturated zone. Most metal concentrations were strongly pH-dependent but also reflected the geochemical characteristics of the parent sands or sandstones. H+ and trace element concentrations were slightly higher beneath areas of afforestation than beneath heathland. The downward fluxes of solutes have been estimated using rainfall-derived chloride as a non-reactive solute. The profiles retain a record of 10-20 years input allowing the past inputs from SO4 and other species to be estimated using solute/chloride ratios. Cation exchange sites are probably depleted over a period of decades and there can be a significant decrease in the unsaturated zone pH as a result of increased or sustained acidic deposition. The shallow groundwater environment (0-15 m) in non-carbonate terrains is therefore a sensitive environment where high metal concentrations may be generated and may ultimately lead to water quality problems in shallow water supplies.     

Case study of augmenting livelihood of fishing community at Sagar Island,India, through solar thermal dryer technology

Environment, Development and Sustainability - Drying of fish at the Sagar Island (21.7269° N, 88.1096° E) is generally carried out in open sun on the seashore on plastic sheets or mat of...     

‘Emulsion locks’ for the containment of hydrocarbons during surfactant flushing

Reversible double water in oil in water (W/O/W) emulsions were developed to contain subsurface hydrocarbon spills during their remediation using surfactant flushing. Double emulsions were prepared by emulsifying CaCl₂ solutions in canola oil, and subsequently by emulsifying the W/O emulsions in aqueous sodium alginate solutions. The formation of double emulsions was confirmed with confocal and optical microscopy. The double emulsions reversed and gelled when mixed with the surfactants sodium dodecyl sulfate (SDS) and cocamidopropyl betaine (CPB). Gels can act as ‘emulsion locks’ to prevent spreading of the hydrocarbon plume from the areas treated with surfactant flushing, as shown in sand column tests. Shear rheology was used to quantify the viscoelastic moduli increase (gelation) upon mixing the double emulsion with SDS and CPB. SDS was more effective than CPB in gelling the double emulsions. CPB and SDS could adsorb at the interface between water and model hydrocarbons (toluene and motor oil), lowering the interfacial tension and rigidifying the interface (as shown with a Langmuir trough). Bottle tests and optical microscopy showed that SDS and CPB produced W/O and O/W emulsions, with either toluene or motor oil and water. The emulsification of motor oil and toluene in water with SDS and CPB facilitated their flow through sand columns and their recovery. Toluene recovery from sand columns was quantitated using Gas-Chromatography Mass-Spectroscopy (GC-MS). The data show that SDS and CPB can be used both for surfactant flushing and to trigger the gelation of ‘emulsion locks’. Ethanol also gelled the emulsions at 100 mL/L.