Acceleration of floc-water separation and floc reduction with magnetic nanoparticles during demulsification of complex waste cutting emulsions

Waste cutting emulsions are difficult to treat efficiently owing to their complex composition and stable emulsified structure. As an important treatment method for emulsions, chemical demulsification is faced with challenges such as low flocs–water separation rates and high sludge production. Hence, in this study, Fe₃O₄ magnetic nanoparticles (MNPs) were used to enhance chemical demulsification performance for treating waste cutting emulsions under a magnetic field. The addition of MNPs significantly decreased the time required to attain sludge–water separation and sludge compression equilibrium, from 210 to 20 min. In addition, the volume percentage of sludge produced at the equilibrium state was reduced from 45% to 10%. This excellent flocculation–separation performance was stable over a pH range of 3–11. The magnetization of the flocculants and oil droplets to form a flocculant–MNP–oil droplet composite, and the magnetic transfer of the composite were two key processes that enhanced the separation of cutting emulsions. Specifically, the interactions among MNPs, flocculants, and oil droplets were important in the magnetization process, which was controlled by the structures and properties of the three components. Under the magnetic field, the magnetized flocculant–MNP–oil droplet composites were considerably accelerated and separated from water, and the sludge was simultaneously compressed. Thus, this study expands the applicability of magnetic separation techniques in the treatment of complex waste cutting emulsions.     

干湿法结合工艺回收废弃SCR脱硝催化剂中的钛、钒和钨

利用干湿法结合工艺实现废弃SCR脱硝催化剂中Ti、V和W元素的高效分离和浸出,提出成套废弃SCR脱硝催化剂中Ti、V和W的回收技术。以废弃SCR脱硝催化剂为研究对象,优选Ti、V和W元素最佳浸出工况,研究硫酸溶解法回收TiO₂和有机萃取法回收V₂O₅和WO₃的回收率与纯度。结果表明:酸浸还原浸钒最优工艺条件为温度140℃,液固比30∶1;钠化焙烧浸钨最优工艺条件为煅烧温度750℃,反应物与Na₂CO₃配比（质量比）为1∶1.5,在以上条件下V、W浸出率分别达到97.6%、93.6%。利用硫酸溶解法回收得到的TiO₂产物主要以锐钛矿晶型存在形式,在最佳焙烧温度750℃下,TiO₂回收率达到97.17%,纯度为95.35%。利用有机萃取法回收得到的V₂O₅和WO₃产物的回收率和纯度分别为72.47%、75.43%和93.25%、78.26%。     

预处理对园林垃圾混合物料联合厌氧发酵的影响

采用超声、微波及碱热预处理技术强化园林垃圾、厨余垃圾与果蔬垃圾联合厌氧发酵产气性能,并以未进行预处理的实验组作为对照。结果表明:4组实验pH值在2 d内迅速降低至7.24~7.45,反应后期可稳定在7.7~8.0,表明厌氧消化系统有较强的稳定性。挥发性脂肪酸（volatile fatty acids,VFA）浓度在第2~4天内达到最大值。乙酸和丙酸是4组实验中VFA的主要成分,两者比例之和在70%以上。VFA浓度在第13天后降低到500 mg/L以下,且以乙酸为主。氨氮（TAN）浓度在前4 d内出现一定波动,随后逐渐升高至2190~2410 mg/L。游离氨氮（FAN）浓度呈先降低后增加趋势,并在第13天后逐渐趋于稳定,为144~209 mg/L。沼气中甲烷比例在第2天后均超过50%,并在第11~12天时达到最大值61.4%~63.8%。修正的Gomperts模型模拟结果表明:预处理技术可缩短反应体系厌氧产沼的适应时间,提高前期产气速率。除此之外,超声预处理与碱热预处理可显著提高基质甲烷产率,由未处理时的396 mL/g分别提高到601,536 mL/g,而微波预处理使得反应体系甲烷产量略有降低。     

Development of a static test apparatus for evaluating the performance of three PM2.5 separators commonly used in China

PM_(2.5) separator directly affects the accuracy of PM_(2.5) sampling.The specification testing and evaluation for PM_(2.5) separator is particularly important,especially under China's wide variation of terrain and climate.In this study,first a static test apparatus based on polydisperse aerosol was established and calibrated to evaluate the performance of the PM_(2.5) separators.A uniform mixing chamber was developed to make particles mix completely.The aerosol concentration relative standard deviations of three test points at the same horizontal chamber position were less than 0.57%,and the particle size distribution obeyed logarithmic normal distribution with an R~2 of 0.996.The flow rate deviation between the measurement and the set point flow rate agreed to within ± 1.0% in the range of -40 to 50℃.Secondly,the separation,flow and loading characteristics of three cyclone separators(VSCC-A,SCC-A and SCC112) were evaluated using this system.The results showed that the 50% cutoff sizes(D_(50)) of the three cyclones were 2.48,2.47 and 2.44 μm when worked at the manufacturer's recommended flow rates,respectively.The geometric standard deviation(GSD) of the capture efficiency of VSCCA was 1.23,showed a slightly sharper than SCC-A(GSD = 1.27),while the SCC112 did not meet the relevant indicator(GSD = 1.2 ± 0.1) with a GSD = 1.44.The flow rate and loading test had a great effect on D_(50),while the GSD remained almost the same as before.In addition,the maintenance frequency under different air pollution conditions of the cyclones was summarized according to the loading test.     

Analytical methods and environmental processes of nanoplastics

The degradation of plastic debris may result in the generation of nanoplastics (NPs). Their high specific surface area for the sorption of organic pollutions and toxic heavy metals and possible transfer between organisms at different nutrient levels make the study of NPs an urgent priority. However, there is very limited understanding on the occurrence, distribution, abundant, and fate of NPs in the environment, partially due to the lack of suitable techniques for the separation and identification of NPs from complex environmental matrices. In this review, we first overviewed the state-of-the-art methods for the extraction, separation, identification and quantification of NPs in the environment. Some of them have been successfully applied for the field determination of NPs, while some are borrowed from the detection of microplastics or engineered nanomaterials. Then the possible fate and transport of NPs in the environment are thoroughly described. Although great efforts have been made during the recent years, large knowledge gaps still exist, such as the relatively high detection limit of existing method failing to detect ultralow masses of NPs in the environment, and spherical polystyrene NP models failing to represent the various compositions of NPs with different irregular shapes, which needs further investigation.     

基于野外原位抽注试验和同位素技术的含水层反硝化速率研究

反硝化作用是地下水硝酸盐污染去除最重要的过程.由于水文地质条件和水文地球化学环境的复杂性和不确定性,精准测定含水层反硝化速率是反硝化过程的研究难点.选取潮白河冲洪积扇中部中国环境科学研究院地下水创新野外基地作为研究区,基于野外原位试验和15N同位素示踪法提出一种含水层反硝化速率的测定方法.该方法综合体现了研究区实际水文地质条件和水文地球化学环境对反硝化作用的影响,并充分考虑了硝酸盐在含水层中稀释弥散作用对计算结果的影响.结果表明:①潮白河冲洪积扇中部某地地下26~28 m处于还原环境,含水介质以粉细砂为主,ρ（NO₃-N）平均值为2.77 mg/L.②地下26~28 m反硝化速率在349.52~562.99 μg/（kg·d）（以N计,下同）之间,平均值为450.31 μg/（kg·d）.通过与研究区含水介质、采样深度和硝酸盐背景值相似的国内外案例对比研究,初步评估结果处于合理区间.③测试结果具有一定不确定性,主要来自忽略中间产物NO₂-和NO的计算方法、扰动采样方法、N₂O的操作规范程度及采样频率等方面.研究方法为测定含水层硝酸盐速率研究提供了新的思路,研究结果可为地下水中硝酸盐转化过程机理研究、地下水硝酸盐污染修复及风险管控提供关键的理论支撑数据.      

厦门市冬季PM2.5污染情境识别及其与气象条件的关系

为研究厦门市冬季不同PM_2.5污染情境与气象条件和气团轨迹路径特征的关系,结合PM_2.5观测数据,使用AGAGE（Advanced Global Atmospheric Gases Experiment）统计方法识别2014—2018年冬季厦门市PM_2.5观测值、基线值和污染值情境,通过气象数据统计和气团后向轨迹聚类对不同PM_2.5污染情境下气象条件和气团轨迹路径特征进行探究.结果表明:①厦门市冬季不同PM_2.5污染情境下,ρ（PM_2.5）及PM_2.5污染值情境时长占比均呈波动中下降的趋势,具体表现为冬季PM_2.5观测值、污染值和基线值情境下,ρ（PM_2.5）平均值分别从2014年的42.2、90.7、16.4 μg/m3降至2018年的26.3、56.9、8.8 μg/m3,冬季PM_2.5污染值情境时长占比从2014年的10.2%降至2018年的3.0%.②冬季PM_2.5污染值情境下气象要素呈低风速、低气压、高温度、高相对湿度的特征.③冬季到达厦门市的气团轨迹路径中,局地路径由于大气条件稳定易累积形成PM_2.5污染;偏北路径和西北路径易从临近省份携带污染物输入导致PM_2.5污染,属于重要的外源污染输入路径;沿海路径和偏西路径均属于清洁路径,但沿海路径易在福建省北部与偏北路径重合形成污染输入,加强了偏北路径的污染物输送能力.研究显示,近年来厦门市冬季PM_2.5污染有明显减弱趋势,但不利的气象条件和外来污染输入仍会造成PM_2.5污染的发生.      

嘉兴地区农村生活污水时空分布及处理设施现状分析

研究选取嘉兴市下辖农村的160座生活污水处理设施进出水为研究对象,分析了区域农村生活污水污染物时空分布特征及其处理设施现状,以期提高处理设施效率。结果表明:嘉兴市农村生活污水中氮、磷污染较有机污染更严重,ρ（COD）、ρ（TP）、ρ（TN）、ρ（NH₄+-N）年均值分别为142.23,4.02,44.19,27.74 mg/L,各污水处理设施处理效果有很大优化空间,COD、TP、TN、NH₄+-N年均去除率分别为50.5%、29.7%、36.8%、51.7%。农村生活污水空间上呈自西向东、由北至南逐渐减小的分布特征,时间上表现为冬季 > 春季 > 秋季 > 夏季。相关性分析表明,COD、TP、TN、NH₄+-N之间呈极显著正相关（P<0.01）,相关系数为0.688±0.946。设施进水C/N、NH₄+-N/TN年均值分别为3.21、68.9%,传统的单一A2/O处理工艺对低碳源污水处理效果不理想,可通过组合工艺设计、规范运营管理、加强后期监测等有效措施来进一步加强污水处理设施处理效果。     

应用改良型水质综合指数法评价饮用水水质

应用1套改良型水质综合指数法对3种不同类型的饮用水水质进行评价。将选取的26项检测指标按照卫生学意义分为5大类,并对各分类指标赋权。选用内梅罗法和最差因子判别法与五色等级分级法结合对2017年4—8月的3种类型饮用水进行水质评价。除7月和8月的管网水水质为2级（水质综合指数>0.5,蓝色）以外,其余月份的出水水质均达到1级（绿色）评价标准。不同类型饮用水中对水质综合指数影响最大的水质分类指标均是有机污染指标。2种不同类型的净水机出水水质均优于管网末梢水,但需注意个别指标的污染。     

特殊区域地表水环境背景值表征技术方法研究与应用

选取黑龙江省源头水保护区作为研究对象,根据DEM数据对保护区内随机布设的水质监测点控制单元进行划分并提取单元内的相关指标建立监测点背景特性量化模型,基于量化结果提出地表水环境背景值监测方案,建立背景值数据库.选取研究区自然属性指标与空间属性指标,以空间叠置技术与聚类分析方法对研究区地表水进行背景值分区,最终将黑龙江省分为六大地表水水质背景值地理分区,并计算了各分区地表水环境背景值表征范围.表征范围显示：依据现行标准进行水质评价,保护区内水质背景值已超出Ⅱ类水质标准限值.因此,基于水质背景值研究成果提出了考虑背景值影响下的水环境质量评价方法,并将方法应用于研究区,结果表明方法切实可行且优于单因子评价法.研究成果可为区域制定背景值影响下的水环境评价方法提供科学的数据支撑与理论依据.