同源四倍体水稻变异胚囊分类及结实性影响因素

以秋水仙素加倍的同源四倍体水稻三系株系具有高比率的变异胚囊.各种胚囊变异类型在抽穗前1～2 d的主穗和第一分蘖穗中出现频繁,造成正常胚囊的比率大幅降低.按变异胚囊的结构特点和形成方式,变异胚囊分为4种类型:退化型、结构变异型、无融合生殖型和反足细胞增殖型.退化型胚囊包括小胚囊和完全退化胚囊,前者仍有较小的胚囊腔而后者胚囊腔缺失;结构变异包括八核七细胞结构的缺失、重复和位置异常,反映了蓼型胚囊典型结构不同形式的变异;无融合生殖胚囊发生比率极低,主要包括反足胚和卵细胞胚;反足细胞的增殖比较频繁,这导致四倍体胚囊的多样性进一步增加,也对结实性带来一定影响.相关分析表明,同源四倍体水稻结实主要来自3部分:正常胚囊、正常型小胚囊和反足细胞增殖型胚囊.这3种胚囊可能具有较好的育性,其对结实率的贡献程度分别为正常蓼型胚囊的72.44%,正常型小胚囊的15.12%,反足细胞增殖型胚囊的12.44%;完全退化型胚囊和位置异常型胚囊对结实率分别表现出显著和极显著的负相关,表明二者可能是结实性的抑制因素.图2表2参24     

森林地表可燃物含水率与海拔关系研究

大兴安岭天然林保护工程重点区域,也是森林火灾频发的重灾区。收集测定了177组森林地表可燃物含水率数据,整理成列联表,进行列联表分析。结果表明,所研究区域的森林地表可燃物在低海拔含水率较高,随着海拔的升高,含水率呈现明显的降低趋势。研究结果可为进一步建立更加精确的大兴安岭林区森林地表可燃物含水率预测模型提供理论基础,对于该林区火灾预防工作意义重大。     

巷道及边坡工程中的膨胀岩灾害与防治

分析了膨胀岩的胀缩机理及影响因素,总结了近几年的理论研究成果。着重论述了巷道和边坡工程中的膨胀 岩所造成的灾害形式,通过分析诱发灾害的机理,有针对性地提出了一些防治措施。     

1976年香港秀茂坪人工填土边坡滑坡灾害评析

简要介绍了1976年香港秀茂坪人工填土工程在强降雨后所发生的滑坡灾害,香港土木工程署当时根据滑坡 后的调查和试验研究,探讨了滑坡的起因,并提出了整治措施,为香港地区其它人工填土边坡的设计和施工提供了 有益的启示,也为类似滑坡的治理提供了参考依据。     

Biological sulfate removal from acrylic fiber manufacturing wastewater using a two-stage UASB reactor

A two-stage UASB reactor was employed to remove sulfate from acrylic fiber manufacturing wastewater. Mesophilic operation (35±0.5℃) was performed with hydraulic retention time (HRT) varied between 28 and 40 hr. Mixed liquor suspended solids (MLSS) in the reactor was maintained about 8000 mg/L. The results indicated that sulfate removal was enhanced with increasing the ratio of COD/SO₄^2-. At low COD/SO₄^2-, the growth of the sulfate-reducing bacteria (SRB) was carbon-limited. The optimal sulfate removal efficiencies were 75% when the HRT was no less than 38 hr. Sulfidogenesis mainly happened in the sulfate-reducing stage, while methanogenesis in the methane-producing stage. Microbes in sulfate-reducing stage performed granulation better than that in methane-producing stage. Higher extracellular polymeric substances (EPS) content in sulfate-reducing stage helped to adhere and connect the flocculent sludge particles together. SRB accounted for about 31% both in sulfate-reducing stage and methane-producing stage at COD/SO₄^2- ratio of 0.5, while it dropped dramatically from 34% in sulfate-reducing stage to 10% in methane-producing stage corresponding to the COD/SO₄^2- ratio of 4.7. SRB and MPA were predominant in sulfate-reducing stage and methane-producing stage respectively.     

Study on the hydrolysis/precipitation behavior of Keggin Al13 and Al30 polymers in polyaluminum solutions

The hydrolysis/precipitation behaviors of Al³⁺, Al₁₃ and Al₃₀ under conditions typical for flocculation in water treatment were investigated by studying the particulates' size development, charge characteristics, chemical species and speciation transformation of coagulant hydrolysis precipitates. The optimal pH conditions for hydrolysis precipitates formation for AlCl₃, PAC_Al13 and PAC_Al30 were 6.5–7.5, 8.5–9.5, and 7.5–9.5, respectively. The precipitates' formation rate increased with the increase in dosage, and the relative rates were AlCl₃ ? PAC_Al30 > PAC_Al13. The precipitates' size increased when the dosage increased from 50 μM to 200 μM, but it decreased when the dosage increased to 800 μM. The Zeta potential of coagulant hydrolysis precipitates decreased with the increase in pH for the three coagulants. The iso-electric points of the freshly formed precipitates for AlCl₃, PAC_Al13 and PAC_Al30 were 7.3, 9.6 and 9.2, respectively. The Zeta potentials of AlCl₃ hydrolysis precipitates were lower than those of PAC_Al13 and PAC_Al30 when pH > 5.0. The Zeta potential of PAC_Al30 hydrolysis precipitates was higher than that of PAC_Al13 at the acidic side, but lower at the alkaline side. The dosage had no obvious effect on the Zeta potential of hydrolysis precipitates under fixed pH conditions. The increase in Zeta potential with the increase in dosage under uncontrolled pH conditions was due to the pH depression caused by coagulant addition. Al–Ferron research indicated that the hydrolysis precipitates of AlCl₃ were composed of amorphous Al(OH)₃ precipitates, but those of PAC_Al13 and PAC_Al30 were composed of aggregates of Al₁₃ and Al₃₀, respectively. Al³⁺ was the most un-stable species in coagulants, and its hydrolysis was remarkably influenced by solution pH. Al₁₃ and Al₃₀ species were very stable, and solution pH and aging had little effect on the chemical species of their hydrolysis products. The research method involving coagulant hydrolysis precipitates based on Al–Ferron reaction kinetics was studied in detail. The Al species classification based on complex reaction kinetic of hydrolysis precipitates and Ferron reagent was different from that measured in a conventional coagulant assay using the Al–Ferron method. The chemical composition of Al_a, Al_b and Al_c depended on coagulant and solution pH. The Al_b measured in the current case was different from Keggin Al₁₃, and the high Al_b content in the AlCl₃ hydrolysis precipitates could not used as testimony that most of the Al³⁺ was converted to highly charged Al₁₃ species during AlCl₃ coagulation.     

典型工业无组织源VOCs排放特征

选取制药厂、酿酒厂和橡胶厂分析了不同工艺过程VOCs排放特征.结果表明,制药厂安乃近合成和氨基比林合成的VOCs排放以苯、甲苯和苯乙烯等苯系物为主,乙酰氨基酚合成的VOCs排放主要以C4～C6的烷烃为主,酿酒厂和橡胶厂VOCs排放均以甲苯、乙苯和间,对二甲苯为主.采用最大增量反应活性法对臭氧生成潜势进行分析,制药厂安乃近合成和氨基比林合成VOCs单位臭氧生成潜势以苯、甲苯等苯系物为主;乙酰氨基酚合成以顺-2-丁烯、甲苯和异戊烷为主;酿酒厂、橡胶厂以甲苯、乙苯、间,对二甲苯为主.同时采用阈稀释倍数对VOCs进行恶臭分析,制药厂和酒厂无组织排放VOCs恶臭污染程度较轻,橡胶厂的伸缩装置车间和硫化车间的无组织VOCs排放存在一定程度的恶臭污染.     

2005年秋季长江口及其邻近水域浮游植物群集

采用Utermhl分析方法,对长江口及其邻近水域（30.5° ~ 32.5° N,121.0° ~ 123.5° E）2005年秋季浮游植物进行了分析,并对其与环境之间的关系做了进一步的探讨。结果表明：调查区初步鉴定浮游植物95种（含变种和变型）,硅藻是主要的浮游植物类群,其丰度比例达到93.1%;生态类型多为温带近岸种,少数为暖水种和大洋种;优势种主要为中肋骨条藻〖WTBX〗（Skeletonema costatum）、具槽帕拉藻（Paralia sulcata）、菱形海线藻（Thalassionema nitzschioides）和圆海链藻（Thalassiosira rotula）〖WTBZ〗;浮游植物平均丰度为2.04 cells/mL,高值出现在长江口门偏南水域;Margalef指数、Shannon Wiener指数以及Pielou指数的分布显示：秋季调查区离岸海域浮游植物多样性程度高,物种均一性好。Pearson相关分析结果显示：海水温度和硝酸盐含量是控制调查区浮游植物分布格局的主要环境因子;优势种中肋骨条藻与温度呈极显著负相关,与硝酸盐呈极显著正相关。     

Ⅱ.尾矿砂对重金属的吸附作用

本文研究了尾矿砂颗粒对Cu,pb,Cd三种重金属离子的吸附作用,以及各种环境条件因素对颗粒表面吸附作用的影响。实验结果表明,细微尾矿砂颗粒对溶液中的重金属离子具有较强烈的吸附作用,并且强烈地依赖于溶液的pH。根据表面络合反应,对尾矿砂颗粒表面基团可能参与的表面络合反应和吸附的重金属形态进行了讨论,并应用简化络合反应模式,求取了尾矿砂颗粒与Cu,Pb,Cd的表面络合形成的条件稳定常数pK_(ad)。     

射流曝气器研究进展

射流曝气技术的应用与完善 ,有赖于射流曝气器的研制与发展。本文综述了射流曝气器的研究进展 ,并根据供气方式、工作压力、结构类型、安装方式、安装高度进行了分类 ,其中着重详述了对研发射流器比较重要的结构类型 ,最后指出射流曝气器的研究趋势