Mo-N-TiO2光催化剂的制备、表征及其活性提高机制

以钼酸铵和氨水分别为钼源和氮源,采用溶胶-凝胶法制备了Mo-N-TiO2光催化剂,并对其进行了XRD、XPS和UV-visDRS表征。XRD结果表明,Mo、N共掺杂有效抑制了TiO2晶粒的生长,提高了TiO2由锐钛矿向金红石相的转变温度。UV-vis表明,Mo-N-TiO2光催化剂可见光吸收能力增强,吸收带边明显"红移",且钼酸铵添加量(相对TiO2)为0.5%的样品"红移"程度最大,最大吸收带边为550 nm。XPS分析结果表明,Mo取代了TiO2晶格中的部分Ti4+,以Mo6+形式存在的,而N以Ti—N及N—Ti—O形式存在。以罗丹明B为模型污染物,重点考察了钼酸铵添加量与焙烧温度对Mo-N-TiO2光催剂性能的影响。结果表明,400℃焙烧下、钼酸铵添加量为0.5%的样品催化活性最好。模拟太阳光下光照120min对罗丹明B的降解率达到96.8%,是纯TiO2的2.42倍。     

Using biochar for remediation of soils contaminated with heavy metals and organic pollutants

Soil contamination with heavy metals and organic pollutants has increasingly become a serious global environmental issue in recent years. Considerable efforts have been made to remediate contaminated soils. Biochar has a large surface area, and high capacity to adsorb heavy metals and organic pollutants. Biochar can potentially be used to reduce the bioavailability and leachability of heavy metals and organic pollutants in soils through adsorption and other physicochemical reactions. Biochar is typically an alkaline material which can increase soil pH and contribute to stabilization of heavy metals. Application of biochar for remediation of contaminated soils may provide a new solution to the soil pollution problem. This paper provides an overview on the impact of biochar on the environmental fate and mobility of heavy metals and organic pollutants in contaminated soils and its implication for remediation of contaminated soils. Further research directions are identified to ensure a safe and sustainable use of biochar as a soil amendment for remediation of contaminated soils.     

城市生活垃圾渗透系数测试研究

采用常水头测渗实验，对不同压实密度和水力梯度下的新鲜垃圾与陈垃圾的渗透系数进行测试，根据达西定律求得渗透系数值。由于垃圾的不均匀性、小颗粒的运动和大孔隙沟道流的形成和改变，实验初始阶段渗透系数值先增大至峰值，然后缓慢降低直至趋于稳定。实验稳定后，新鲜垃圾压实密度为0．75—0．95t／m^3时，渗透系数值约为1．26E-03～1．43E-03cm／s。陈垃圾在压实密度分别为1．2和1．4t／m^3时，渗透系数为8．29E-04和1．35E-04cm／s。     

厌氧-局部循环供氧生物膜技术处理农村污水

通过模拟农村生活污水水质和间歇进水特点,利用“厌氧-局部循环供氧生物膜”技术,研究该工艺对有机物、氮、磷的去除效果.厌氧池和局部循环供氧池有效容积比为1∶1.6,曝气装置位于局部循环供氧池中间底部,环形导流板将局部循环供氧池分隔成中间好氧区和四周缺氧区,斜管沉淀池前置到厌氧池与局部循环供氧池之间,出水端设置循环水池.装置连续稳定运行12个月,平均进水量为140 L/d,生物反应区HRT为1.3d.监测结果表明,出水COD、BOD、NH3-N、TN和TP平均浓度分别在40.31、3.38、2.69、11.98和0.75 mg/L,达到了国家城镇污水处理厂污染物排放指标(GB-18918-2002)中的一级排放标准.研究表明,厌氧-局部循环供氧技术是一种适合农村分散污水处理的新工艺,可有效减轻农业面源污染.     

棉秆基活性炭的制备及其对2,4-二硝基苯酚的吸附

以棉秆为原料,以KOH为活化剂,制备了高比表面棉秆基生物质活性炭。分析了制得的活性炭的元素组成、表面官能团、吸附能力等物化性能,探讨了浸渍比,活化温度,活化时间等工艺参数对制备活性炭得率、表面官能团、碘值、亚甲基蓝值等性能的影响,并通过静态吸附实验比较了不同条件下制备活性炭对2,4-二硝基苯酚的吸附性能,探讨了典型炭样品对2,4-二硝基苯酚的等温吸附特性。结果表明,KOH活化棉秆基生物质活性炭的表面物化性质随浸渍比、活化温度等工艺参数变化而变化,活化适宜条件为浸渍比1：3、活化温度800℃、活化时间90 min,在此条件下制得的炭样的碘值为1 251 mg/g,亚甲基蓝吸附值为478 mg/g,分别是国家一级品标准的1.25倍与3.54倍;对2,4-二硝基苯酚的Langmuir最大吸附量为747 mg/g,与Freundlich模型相比,Langmuir模型能较好地描述2,4-二硝基苯酚在炭样上的吸附行为,表明制备活性炭样品表面吸附位的能量分布较为均一。     

Deep learning architecture for air quality predictions

With the rapid development of urbanization and industrialization, many developing countries are suffering from heavy air pollution. Governments and citizens have expressed increasing concern regarding air pollution because it affects human health and sustainable development worldwide. Current air quality prediction methods mainly use shallow models; however, these methods produce unsatisfactory results, which inspired us to investigate methods of predicting air quality based on deep architecture models. In this paper, a novel spatiotemporal deep learning (STDL)-based air quality prediction method that inherently considers spatial and temporal correlations is proposed. A stacked autoencoder (SAE) model is used to extract inherent air quality features, and it is trained in a greedy layer-wise manner. Compared with traditional time series prediction models, our model can predict the air quality of all stations simultaneously and shows the temporal stability in all seasons. Moreover, a comparison with the spatiotemporal artificial neural network (STANN), auto regression moving average (ARMA), and support vector regression (SVR) models demonstrates that the proposed method of performing air quality predictions has a superior performance.     

Formation of shaped barium sulfate-dye hybrids: waste dye utilization for eco-friendly treatment of wastewater

Purpose

Owing to the present complexity and difficulty of concentrated dye wastewater treatment, this work aimed to synthesize a reproducible waste-sorbing material for the treatment of wastewater by forming the dye-conjugating complex hybrid.

Methods

The inorganic/organic hybridization was applied to prepare the objective material by immobilizing waster dye-Mordant blue 9 (MB) with barium sulfate (BaSO₄). The composition and pattern of the formed material were determined by spectrometry and characterized by SEM and XRD, and their formation process was clarified. The adsorption of cationic dye-basic blue BO (BB) and copper ion was investigated..

Results

The hybrid of MB alone into growing BaSO₄ formed the pineapple-like particles while that of the MB/BB-conjugating complex was the rhombus material. The adsorption of BB on the MB–BaSO₄ hybrid was probably attributed to ion-pair equilibrium and that of Cu²⁺ may result from the complexation. The treatment of dye and heavy metal wastewaters indicated that the MB hybrid material removed 99.8% BB and 97% Cu²⁺ and the dye-conjugating hybrid with growing BaSO₄ 100% MB, 99.5% BB, and 44% Cu²⁺.

Conclusion

The waste MB–BaSO₄ hybrid material is efficient to treat cationic dye and Cu²⁺ wastewater. The dye-conjugating hybridization method is the first to be advanced for in situ wastewater treatment, and it showed a combined effect for the removal of both organic dyes and heavy metals.     

Cadmium accumulation, activities of antioxidant enzymes, and malondialdehyde (MDA) content in Pistia stratiotes L.

The aquatic plant Pistia stratiotes L. (water lettuce) was studied due to its capability of absorption of contaminants in water and its subsequent use in wetlands constructed for wastewater treatment. The effects of Cd on root growth, accumulation of Cd, antioxidant enzymes, and malondialdehyde (MDA) content in P. stratiotes were investigated. The results indicated that P. stratiotes has considerable ability to accumulate Cd. Cadmium induced higher superoxide dismutase (SOD) and peroxidase (POD) activities than catalase activity, suggesting that SOD and POD provided a better defense mechanism against Cd-induced oxidative damage. The accumulation of Cd promoted MDA production.     

氧化铁改性砂联合生物预处理对氨氮的吸附特性

对含氨氮(NH3-N)的微污染原水,采用自制氧化铁改性石英砂(iron oxide coated sand,IOCS)滤料强化过滤与生物预处理技术联合,进行强化处理与吸附效果研究.结果表明,采用强化挂膜法,生物预处理反应器的生物膜成熟期约为7 d,其对氨氮的去除率为60%~70%,但反应器中存在亚硝酸盐氮积累的现象.IOCS与生物预处理技术联合,对NH3-N的平均去除率为84.67%,出水NH3-N浓度均低于0.5 mg/L,NO2--N含量趋于0;而普通石英砂(RQS)在同等条件下,对氨氮的去除效果不稳定,平均去除率为74.31%,出水NH3-N平均浓度未达标,对NO2--N平均去除率仅有33.29%.在4 m/h滤速工况下,与生物预处理技术联合,IOCS和RQS对NH3-N最高去除率分别为94.3%和82.72%.IOCS与RQS的表面形态结构存在明显差异:前者的表面结构更加复杂多孔,比表面积大,有利于生物牢固附着;后者表面较光滑,比表面积小,挂膜后生物易脱落.     

Endosulfan in China 1—gridded usage inventories

Background, aim, and scope  Endosulfan, an organochlorine pesticide (OCP), is genotoxic in mammalian cells and generally considered to be toxic and classified by the World Health Organization and the US Environmental Protection Agency as priority pollutants and a nominator for inclusion in a future iteration of the persistent organic pollutants treaty. Endosulfan is a currently used pesticide and still being used worldwide. The general trend of total global endosulfan use has increased continuously since the first year when this pesticide was applied. It is critical to create national endosulfan usage/emission inventories for China to carry out source–receptor relation analysis, risk assessment, and other research related to endosulfan in this country. Chinese inventories have been published for some OCPs, such as technical HCH and lindane, DDT, and chlordane; for endosulfan, however, there has not been any usage inventory available on any scales (national or provincial), although endosulfan has been widely used since 1994 in this country. This is the first part of the work. The goal of this paper is to quantify the historical production and usage of endosulfan in China and to compile gridded historical usage inventories of endosulfan for this country. Based on these usage inventories, emission and residue inventories will be created, which is the goal of the second part of the work. Materials and methods  Due to the lack of national production and usage information of endosulfan in China, a method to estimate the use of endosulfan was developed. First, information of crops on which endosulfan is applied and average endosulfan use and annual application frequencies of endosulfan on these crops were collected. Secondly, usage of endosulfan on each crop was estimated using the national cropland area for each province from Chinese government reports. Finally, with the help of GIS (geographic information system), the usage data of this insecticide was allocated to a grid system, with a 1/4° longitude by 1/6° latitude resolution, with a size for each grid cell of approximately 25 km by 25 km. Results and discussion  The use of endosulfan in agriculture in China started on cotton in 1994, and on wheat, tea, tobacco, apples, and other fruits in 1998. Endosulfan usage on cotton, wheat, tea, tobacco, and apples in China has been estimated to be approximately 25,700 t between 1994 and 2004. The province with the highest usage of endosulfan is Henan Province, with a total usage reaching 4,000 t, followed by the uses in Xinjiang Autonomous Region (3,200 t), Shandong Province (3,000 t), Hebei Province (2,100 t), and Anhui Province (1,900 t). Gridded usage inventories of endosulfan at a 1/4° longitude by 1/6° latitude resolution have been created, which indicate that the intensive endosulfan use was in the south of Hebei Province, west of Shandong Province, east of Henan Province, north of Anhui Province, east of Jiangsu Province, and some areas in Yunnan Province and Xinjiang Autonomous Region. General agreement has been found between the usage data from our estimation and the small amount of usage data published in China. Conclusions  This is the first national gridded endosulfan usage inventory produced for China. The annual applications of endosulfan from 1994 to 2004 in China were estimated based on the total areas of major crops, on which endosulfan was applied, and spatial distribution of the application was generated at provincial and prefecture levels. With the help of GIS, endosulfan usage based on prefecture was transferred to a 1/4° longitude by 1/6° latitude gridding system. The satisfaction of the inventories was supported by the consistence between the estimation of the annual usage and the reported annual production of endosulfan. Recommendations and perspectives  This gridded endosulfan usage inventory created in this study will be improved upon availability of new information of endosulfan. The usage inventories can be used to create gridded emission and residue inventories for this insecticide. It is believed that this work will pave the way for further endosulfan studies in China and beyond.