Source apportionment of ultrafine and fine particle concentrations in Brisbane, Australia

Purpose

To investigate the significance of sources around measurement sites, assist the development of control strategies for the important sources and mitigate the adverse effects of air pollution due to particle size.

Methods

In this study, sampling was conducted at two sites located in urban/industrial and residential areas situated at roadsides along the Brisbane Urban Corridor. Ultrafine and fine particle measurements obtained at the two sites in June?CJuly 2002 were analysed by positive matrix factorization.

Results

Six sources were present, including local traffic, two traffic sources, biomass burning and two currently unidentified sources. Secondary particles had a significant impact at site 1, while nitrates, peak traffic hours and main roads located close to the source also affected the results for both sites.

Conclusions

This significant traffic corridor exemplifies the type of sources present in heavily trafficked locations and future attempts to control pollution in this type of environment could focus on the sources that were identified.     

Fungal spore fragmentation as a function of airflow rates and fungal generation methods

The aim of this study was to characterise and quantify the fungal fragment propagules derived and released from several fungal species (Penicillium, Aspergillus niger and Cladosporium cladosporioides) using different generation methods and different air velocities over the colonies. Real time fungal spore fragmentation was investigated using an Ultraviolet Aerodynamic Particle Sizer (UVASP) and a Scanning Mobility Particle Sizer (SMPS). The study showed that there were significant differences (p < 0.01) in the fragmentation percentage between different air velocities for the three generation methods, namely the direct, the fan and the fungal spore source strength tester (FSSST) methods. The percentage of fragmentation also proved to be dependent on fungal species. The study found that there was no fragmentation for any of the fungal species at an air velocity ≤0.4 m s^?1 for any method of generation. Fluorescent signals, as well as mathematical determination also showed that the fungal fragments were derived from spores. Correlation analysis showed that the number of released fragments measured by the UVAPS under controlled conditions can be predicted on the basis of the number of spores, for Penicillium and A. niger, but not for C. cladosporioides. The fluorescence percentage of fragment samples was found to be significantly different to that of non-fragment samples (p < 0.0001) and the fragment sample fluorescence was always less than that of the non-fragment samples. Size distribution and concentration of fungal fragment particles were investigated qualitatively and quantitatively, by both UVAPS and SMPS, and it was found that the UVAPS was more sensitive than the SMPS for measuring small sample concentrations, whilethe results obtained from the UVAPS and SMAS were not identical for the same samples.     

Variations of arsenic species content in edible Boletus badius growing at polluted sites over four years

The content of arsenic (As) in mushrooms can vary depending on the concentration level of this metalloid in the soil/substrate. The present study evaluated the content of arsenic in Boletus badius fruiting bodies collected from polluted and non-polluted sites in relation to the content of this element in overgrown substrate. It was found that mushrooms from the arsenic-polluted sites contained mean concentrations from 49 to 450 mg As kg^?1 dry matter (d.m.), with the greatest content found for specimens growing in close proximity of sludge deposits (490±20 mg As kg^?1d.m.). The mean content of total arsenic in mushrooms from clean sites ranged from 0.03 to 0.37 mg kg^?1 It was found that B. badius could tolerate arsenic in soil substrate at concentrations of up to 2500 mg kg^?1, at least. In different years of investigation, shifts in particular arsenic forms, as well as a general increase in the accumulation of organic arsenic content, were observed. The results of this study clearly indicate that B. badius should not be collected for culinary purposes from any sites that may be affected by pollution.     

Change of PCBs and forms of heavy metals in sewage sludge during thermophilic anaerobic digestion

Determination of seven congeners of PCBs was carried out for sewage sludge before, during and after thermophilic digestion. The overall content of heavy metals (Zn, Cu, Ni, Cd, Pb, Cr) in sludge before and after digestion was determined. Moreover the concentration of heavy metals in particular chemical fractions of the sludge was analyzed. After the thermophilic digestion total concentration of seven PCBs was reduced by 47%, which suggests that thermophilic digestion affects PCB reduction positively. On the 10th d of the process, concentration of lower chlorinated PCBs increased, whereas those of higher chlorinated PCBs decreased. The thermophilic digestion process showed no accumulation of the studied heavy metals in the mobile fractions (exchangeable and carbonate) of the stabilized sewage sludge, except for nickel. The highest increase in zinc, copper, cadmium, and chromium concentration was observed in the organic-sulfide fraction, whereas the highest increase in lead was found in the residual fraction of the sludge. In case of nickel both fractions of organic-sulfide and exchangeable-carbonate fractions were enriched.     

Quantitative modelling to estimate the transfer of pharmaceuticals through the food production system

Use of pharmaceuticals in animal production may cause an indirect route of contamination of food products of animal origin. This study aimed to assess, through mathematical modelling, the transfer of pharmaceuticals from contaminated soil, through plant uptake, into the dairy food production chain. The scenarios, model parameters, and values refer to contaminants in emission slurry production, storage time, immission into soil, plant uptake, bioaccumulation in the animal's body, and transfer to meat and milk. Modelling results confirm the possibility of contamination of dairy cow's meat and milk due the ingestion of contaminated feed by the cattle. The estimated concentration of pharmaceutical residues obtained for meat ranged from 0 to 6 ng kg^?1 for oxytetracycline, from 0.011 to 0.181 μg kg^?1 for sulfamethoxazole, and from 4.70 to 11.86 μg kg^?1 for ketoconazole. The estimated concentrations for milk were: zero for oxytetracycline, lower than 40 ng L^?1 for sulfamethoxazole, and from 0.98 to 2.48 μg L^?1 for ketoconazole. Results obtained for the three selected pharmaceuticals indicate a minor risk for human health. This study showed that supply chain modelling could be an effective tool in assessing the indirect contamination of feedstuff and animal products by residues of pharmaceuticals. The model can easily be adjusted to other contaminants and supply chain and, in this way, present a valuable tool to underpin decision making.     

Heavy metals, polycyclic aromatic hydrocarbons and polychlorinated biphenyls in surface sediments of the Naples harbour (southern Italy)

The Naples's harbour is one of the largest and most important commercial and tourist port of the Mediterranean basin. It is located on the southeast coast of Italy and receives industrial and municipal wastewaters from the city of Naples. Due to its social and economic impact, a comprehensive assessment of levels and sources of contamination of bottom sediments in this area of the Mediterranean basin is essential to identify potential danger due to mobilization of contaminants produced by managing of the same sediments. In this study, superficial sediments collected from 189 sampling sites were analyzed for grain size, heavy metals (Cr, Cu, Ni, Pb, V, Zn, Co, Sn, Cd, Hg, As, Al and Fe), 16 priority polycyclic aromatic hydrocarbons (PAHs) and perylene and 38 individual polychlorinated biphenyl (PCB) congeners. Compared to the estimated local background, Cu, Zn, Pb, Cd, Sn and Hg show enrichment factors >3 and only Hg evidences a median value higher than the NOAA (effects range - median) guidelines. Principal component analysis allowed us to clearly discriminate two areas mainly affected by heavy metals contamination and influenced by different sources related to industrial, commercial and/or urban activities. Priority PAHs are predominantly represented by three-five-ring compounds with concentrations ranging between 9 and 31774 ng g(-1) and frequently higher than the NOAA ER-M index. A prevalent pyrolitic origin of PAH was assessed on the basis of the relative abundance of the different congeners and selected isomer ratios. The concentrations of PCBs, as sum of the 38 congeners, ranged from 1 to 899 ng g(-1), with a predominance of highly chlorinated (tetra- and penta-chlorobiphenyls) congeners. WHO-TEQ values, calculated for the PCDD-like PCB congeners, suggest a relatively high level of toxicity. Generally, the concentration of PAHs and PCBs were higher near the sites of intense industrial, shipping and/or commercial activities suggesting a direct influence of these sources on the pollutant distribution patterns.     

Derivation of motor vehicle tailpipe particle emission factors suitable for modelling urban fleet emissions and air quality assessments

Background, aim and scope  

Urban motor vehicle fleets are a major source of particulate matter pollution, especially of ultrafine particles (diameters < 0.1 μm), and exposure to particulate matter has known serious health effects. A considerable body of literature is available on vehicle particle emission factors derived using a wide range of different measurement methods for different particle sizes, conducted in different parts of the world. Therefore, the choice as to which are the most suitable particle emission factors to use in transport modelling and health impact assessments presented as a very difficult task. The aim of this study was to derive a comprehensive set of tailpipe particle emission factors for different vehicle and road type combinations, covering the full size range of particles emitted, which are suitable for modelling urban fleet emissions.     

The effects of different electrode materials on seed germination of Solanum nigrum L. and its Cd accumulation in soil

The effects of different electrode on Solanum nigrum L.seed germination were determined.The result showe d that germination percentage(GP) of seeds in treatment T2(titanium electrode) was 26.6% higher than in control(CK,without electric field).High potassium and calcium concentrations were beneficial for seed enzymatic activity in treatment T2,which could partly explain the increase in GP.Cd accumulation(μg/pot) in S.nigrum treated with any electric field was significantly higher(p<0.05) than...