Cu-SBA-15催化湿式过氧化氢氧化水溶液中罗丹明B

采用水热晶化法合成了不同含铜量的Cu-SBA-15介孔分子筛,并且用XRD、N2吸附、TEM以及UV-vis对所合成的样品进行表征。以Cu-SBA-15为催化剂,H2O2为氧化剂,催化湿式过氧化水溶液中的罗丹明B,主要考察H2O2浓度、催化剂用量、处理温度、初始pH等因素对罗丹明B氧化效果的影响。结果表明,在同样的处理条件下罗丹明的脱色率明显高于TOC去除率,处理温度、初始pH对罗丹明B的脱色与氧化有重要影响。在罗丹明B初始浓度100 mg/L,H2O2初始浓度1.8 g/L,催化剂量0.3 g/L,温度60℃,pH为7.0,处理时间100 min时,罗丹明B的脱色率为98.6%,TOC去除率为62.8%。     

Synthesis of iron composites on nano-pore substrates: Identification and its application to removal of cyanide

Two types of nano-pore substrates, waste-reclaimed (WR) and soil mineral (SM) with the relatively low density, were modified by the reaction with irons (i.e. Fe(II):Fe(III) = 1:2) and the applicability of the modified substrates (i.e. Fe-WR and Fe-SM) on cyanide removal was investigated. Modification (i.e. Fe immobilization on substrate) decreased the BET surface area and PZC of the original substrates while it increased the pore diameter and the cation exchange capacity (CEC) of them. XRD analysis identified that maghemite (γ-Fe₂O₃) and iron silicate composite ((Mg, Fe)SiO₃) existed on Fe-WR, while clinoferrosilite (FeSiO₃) was identified on Fe-SM. Cyanide adsorption showed that WR adsorbed cyanide more favorably than SM. The adsorption ability of both original substrates was enhanced by the modification, which increased the negative charges of the surfaces. Without the pH adjustment, cyanide was removed as much as 97% by the only application of Fe-WR, but the undesirable transfer to hydrogen cyanide was possible because the pH was dropped to around 7.5. With a constant pH of 12, only 54% of cyanide was adsorbed on Fe-WR. On the other hand, the pH was kept as 12 without adjustment in Fe-WR/H₂O₂ system and cyanide was effectively removed by not only adsorption but also the catalytic oxidation. The observed first-order rate constant (k_obs) for cyanide removal were 0.49 (±0.081) h⁻¹. Moreover, the more cyanate production with the modified substrates indicated the iron composites, especially maghemite, on substrates had the catalytic property to increase the reactivity of H₂O₂.     

Natural and anthropogenic influences on a red-crowned crane habitat in the Yellow River Delta Natural Reserve, 1992–2008

This study aims to assess the relative importance of natural and anthropogenic variables on the change of the red-crowned crane habitat in the Yellow River Nature Reserve, East China using multitempopral remote sensing and geographic information system. Satellite images were used to detect the change in potential crane habitat, from which suitable crane habitat was determined by excluding fragmented habitat. In this study, a principal component analysis (PCA) with seven variables (channel flow, rainfall, temperature, sediment discharge, number of oil wells, total length of roads, and area of settlements) and linear regression analyses of potential and suitable habitat against the retained principal components were applied to explore the influences of natural and anthropogenic factors on the change of the red-crowned crane habitat. The experimental results indicate that suitable habitat decreased by 5,935 ha despite an increase of 1,409 ha in potential habitat from 1992 to 2008. The area of crane habitat changed caused by natural drivers such as progressive succession, retrogressive succession, and physical fragmentation is almost the same as that caused by anthropogenic forces such as land use change and behavioral fragmentation. The PCA and regression analyses revealed that natural factors (e.g., channel flow, rainfall, temperature, and sediment discharge) play an important role in the crane potential habitat change and human disturbances (e.g., oil wells, roads, and settlements) jointly explain 51.8 % of the variations in suitable habitat area, higher than 48.2 % contributed by natural factors. Thus, it is vital to reduce anthropogenic influences within the reserve in order to reverse the decline in the suitable crane habitat.     

基于权重敏感度分布研究太湖有机磷农药单一和复合风险

基于实验室能得到的有限毒性数据的物种敏感度分布法(species sensitivity distribution, SSD)很难充分代表特定区域生态系统的物种分布,需要采用考虑生物区系特征进行赋予权重的物种敏感度分布法(weighted species sensitivity distribution,WSSD)。基于太湖物种组成构建WSSD,使用最大累积率(maximum cumulative ratio, MCR)(含风险商法(hazard quotient, HQ))和概率风险评价法(probabilistic risk assessment, PRA)对太湖地区单一和混合有机磷农药的风险进行研究。结果表明,相对于传统SSD方法,加权SSD方法计算的风险商大,且5%生物受影响的概率更大。单一风险评价中,敌敌畏和乐果5%生物受影响的概率超过40%,需要优先控制;最大累积率表明,敌敌畏是复合风险的主要贡献者,单一风险评价中风险较小的马拉硫磷和对硫磷也对复合风险贡献较大,复合暴露风险评价是必要的,混合物的风险商>1,5%生物受复合暴露影响的概率高达90%,有机磷农药复合生态风险不容忽视。     

Analysis of injury mechanism of the elderly and non-elderly groups in minor motor vehicle accidents

Abstract

Objective: The purpose of this study is to investigate the injury patterns of noncatastrophic accidents by individual age groups.

Methods: Data were collected from the Korean In-Depth Accident Study database based on actual accident investigation. The noncatastrophic criteria were classified according to U.S. experts from the Centers for Disease Control and Prevention’s recommendations for field triage guidelines of high-risk automobile crash criteria by vehicle intrusions more than 12 in. on occupant sites (including the roof) and more than 18 in. on any site. The Abbreviated Injury Scale (AIS) was used to determine injury patterns for each body region. Severely injured patients were classified as Maximum Abbreviated Injury Scale (MAIS) 3 or higher.

Results: In this study, the most significant injury regions were the head and neck, extremities, and thorax. In addition, the incidence of severe injury among elderly patients was nearly 1.6 times higher than that of non-elderly patients. According to age group, injured body regions among the elderly were the thorax, head and neck, and extremities, in that order. For the non-elderly groups, these were head and neck, extremities, and thorax. Severe injury rates were slightly different for the elderly group (head and neck, abdomen) and non-elderly group (thorax, head and neck).

Conclusions: In both age groups, the rate of severe injury is proportional to an increase in crush extent zone. Front airbag deployment may have a relatively significant relationship to severe injuries.     

Modelling the connection between energy consumption and carbon emissions in North Africa: Evidence from panel models robust to cross-sectional dependence and slope heterogeneity

Environment, Development and Sustainability - This paper explored the link between energy consumption and carbon emissions in North Africa through an Environmental Kuznets Curve (EKC) framework....     

Changes in Chlorinated Organic Pollutants and Heavy Metal Content of Sediments during Pyrolysis (7 pp)

Background There has been an increasing concern about the treatment and disposal of contaminated sediment from dredged river, harbor or estuary due to the accumulated toxic organics such as dioxins and inorganics particularly heavy metals like Cr, Pb, Zn, Cu, Hg and Cd. However, considering the huge amount of materials and financial costs involved, any candidate technology must ultimately result to reusable residual by-products. This can only be made possible if the toxic pollutants are removed or stabilized in the raw sediment and then fed back into the materials cycle. Currently, we are developing a pyrolysis process for the commercial-scale cleanup of dioxins and heavy metal-contaminated river sediment to yield reusable char for various economical applications. In this connection, this paper describes our preliminary investigation into the extent of dioxins and heavy metal volatilization from actual contaminated sediment. The stabilization of certain metallic species particularly Cr ions was studied. Methods Laboratory scale pyrolysis experiments were conducted using a special horizontal lab-scale pyrolyzer. Sediment samples from Shanghai Suzhou Creek and Tagonoura Harbor were pyrolyzed in the reactor under nitrogen gas at 800°C and different retention times of 30, 60 and 90 min. A constant heating rate of 10°C min-1 was employed. The pyrolysis gas was first allowed to pass through a cold trap to condense the tar. Uncondensed gases were then channeled through a column containing an adsorbent (XAD-2 Resin) for dioxins. Heavy metal concentrations in the initial and final sediment residues were analyzed by ICP (Nippon Jarrel-Ash) following their acid and alkali (for Cr6+) digestion. Dioxins content of the pyrolysis char, tar, and exhaust gases in the dioxin adsorbent were also determined. For comparative purpose, thermal treatment under air flow was conducted. Results The data for the removal of heavy metals from Suzhou Creek sediment showed very significant reductions in Pb, Zn and Cr6+ content of the sediment at this condition. Percentage removals were 42.4%, 60.8% and 42.2%, respectively. The disappearance of Cr6+ was due to reduction reactions rather than volatilization since the total Cr content remained almost unchanged. Other heavy metals such as Cu, Fe and Ni showed very minimal reductions. Nonetheless, Toxicity Characteristics Leaching Procedure (TCLP) tests confirmed that these residual heavy metals were rather stable in the pyrolysis char. Reduction of toxic Cr6+ at 42.2% has also been achieved by pyrolysis (with N2) as opposed to the more than 580 % increase in Cr6+ observed during thermal oxidation (with air). Discussion Pyrolysis also remove toxic organics particularly dioxins from the sediment. For the total dioxins, removal percentage of 99.9999% was achieved even at the lowest retention time of 30 min. Almost all polychlorinated dibenzo-p-dioxine (PCDDs) and polychlorinated dibenzo-furans (PCDFs) were removed at any retention time. The TEQs detected from the solid residues were mainly contributed by dioxin-like PCBs, yet these were present in relatively trace quantities. At the shortest retention time of 30 min, only 0.000085 pg-TEQ g-1 of polychlorinated biphenyls (PCBs) was detected in the pyrolysis char. Furthermore, the residual PCBs have very low toxicity ratings and none of the highly toxic PCBs, which were initially present in the sediment such as 3,3',4,4',5-PeCB and 3,3',4,4'5,5'-HxCB, were detected in the char. Results further confirmed that most of the dioxins that were removed were transferred to the gas phase so that volatilization may be considered as the main mechanism for their removal. Conclusion Some heavy metals particularly Pb and Zn can be volatilized under N2 pyrolysis at 800oC. Pyrolysis also prevented the formation of more toxic Cr6+ ions and at the same time resulted to its reduction by around 42.2% contrast to the 580% increase during thermal oxidation. PCDDs and PCDFs have been removed and were not formed in the solid products over the retention time range of 30-90 min at 800°C. Dioxin-like PCBs mostly remained and a retention time of 30 min was found sufficient for its maximum removal. Recommendations and Perspective . With the above results, a temperature of 800oC at a retention time of 30 min is sufficient for the removal of total dioxins and some heavy metals by volatilization. It is however necessary to destroy the dioxins as well as recover heavy metals in the gas phase. Stability of remaining heavy metals in the char also needs to be confirmed by leaching tests. These are the major concerns, which we are currently evaluating to establish the feasibility of our proposed large scale pyrolysis system for sediment treatment.     

Persistent chlorinated pesticides in fish species from Qiantang River in East China

Thirteen organochlorine pesticides (OCPs) in 18 fish species from Qiantang River were firstly determined by GC-ECD. To elucidate the sources and the environment fate of these pollutants, water and sediment samples were also analyzed for OCPs contents. Total concentrations of OCPs in fish muscles ranged from 7.43 to 143.79 ng g(-1) wet weight (ww) with highest concentration recorded in sole fish (Cynoglossus abbreviatus), a benthic carnivore. The results indicated that carnivore fish have higher OCPs concentration than other fish with different feeding modes. OCPs concentration in fish was in the range of 1.86-5.85, 2.65-133.51 and 1.94-12.48 ng g(-1) for HCHs (alpha-, beta-, gamma-, delta-HCH), DDTs (p,p'-DDD, p,p'-DDE, p,p'-DDT, o,p'-DDD) and other OCPs (aldrin, diedrin, endrin, heptachlor, heptachlor expoide), respectively. The highest OCPs concentration in fish organs of four big fish species was found in brain of silver carp (Hypophthalmichthys molitrix), 289.26 ng g(-1) ww followed by kidney, liver, heart and gill. Among the OCPs analyzed, DDE, gamma-HCH and heptachlor were the predominant contaminants in fish muscle, which indicated that there was recent input of lindane. Significant correlation was observed between concentrations of DDTs and lipid content as well as between OCPs and lipid contents in fish species. Both field water bioconcentration factors (BCF) and sediment BCF showed a positive correlation with octanol-water partition coefficients (Kow) in the sole fish.     

Uptake of oxytetracycline and its phytotoxicity to alfalfa (Medicago sativa L.)

A series of experiments were conducted in a hydroponic system to investigate the uptake of oxytetracycline (OTC) and its toxicity to alfalfa (Medicago sativa L.). OTC inhibited alfalfa shoot and root growth by up to 61% and 85%, respectively. The kinetics of OTC uptake could be well described by Michaelis-Menten equation with Vmax of 2.25 micromol g-1 fresh weight h-1, and Km of 0.036 mM. The uptake of OTC by alfalfa was strongly inhibited by the metabolic inhibitor, 2,4-DNP (2,4-dinitrophenol), at pH 3.5 and 6.0, but not by the aquaporin competitors, glycerol and Ag+. OTC uptake, however, was significantly inhibited by Hg2+, suggesting that the inhibition of influx was due to general cellular stress rather than the specific action of Hg2+ on aquaporins. Results from the present study suggested that OTC uptake into alfalfa is an energy-dependent process.     

Regression method of the hydrophobicity ruler approach for determining octanol/water partition coefficients of very hydrophobic compounds

A regression method was developed for the hydrophobicity ruler approach, which is an indirect method for determining the octanol/water partition coefficients of very hydrophobic compounds. Two constants introduced into the mathematical model were obtained by regression of the absorption data sampled before the partition equilibrium. A water miscible organic solvent was used to increase the solubility of the very hydrophobic compounds in the aqueous solution so that the hydrophobicity scale was reduced and the equilibration was accelerated. Polydimethylsiloxane/methanol aqueous solution and a series of 21 polychlorinated biphenyls (PCBs) were used to demonstrate the regression method. The PCB compounds with known experimental logK(o/w) values served as reference compounds, while the PCB compounds without known logK(o/w) values were determined. The distribution coefficients (logK(p/s)), uptake and elimination rate constants were obtained from the two regression constants for each compound (reference or unknown). The correlation of the logK(p/s) values of the reference PCB compounds with their logK(o/w) values was linear (logK(o/w)=2.69logK(p/s)+0.76, R(2)=0.97). The logK(o/w) values were compared with literature values and suggested that some values from the literature far off the calibration line could be inaccurate. The critical experimental factors, the merits of the regression method were discussed.