发酵类抗生素废水处理工艺及运行效果

介绍了内蒙古某抗生素废水处理厂的处理工艺流程、处理单元类型及其详细设计参数,通过对该污水处理厂半年内运行效果的调研,分析评价该污水处理系统的处理效果及出水指标;该水厂工艺流程对COD、TOC、氨氮、总氮、总磷、BOD和急性毒性的平均去除率分别为96.52%、95.83%、50.24%、55.20%、62.05%、98.52%和99.14%,COD、氨氮、总氮、总磷出水水质分别为477、438、556.7和7.69 mg/L,达到排放到城区下水道要求,园区内所有废水汇集到园区污水处理厂进行集中深度处理达标后排放水体。通过对该水厂工艺的介绍和水质分析,为我国抗生素生产企业面临的废水处理工艺类型选择及工程改造升级提供一定参考。     

厌氧流化床微生物燃料电池及其串并联性能

在高650 mm、有效容积1 280 mL的液固厌氧流化床单室无膜空气阴极微生物燃料电池(MFC)中,研究了燃料电池串并联产电和有机污水处理性能,同时考察了电极面积、活性炭装填体积、温度等因素对产电性能的影响。结果表明,将燃料电池串联,总电压等于3个单级电池的电压之和,约为2 100 mV,最大功率为0.12 mW,而单级电池最大功率为0.05 mW。并联时,输出电压为800 mV,和单级电池输出电压大体相当,而电流为单级电流的2倍。阳极面积增加1倍,产电量增大了30%;电压随活性炭装填体积的增大而增大;温度为40℃时,燃料电池的产电性能最好。     

二氧化钛脱除高温烟气中的氯化氢

HCl是城市垃圾焚烧产生的主要气体污染物之一。将一种新型脱氯剂TiO2引入到垃圾焚烧系统中,并与其他脱氯剂的性能进行比较。研究了不同脱氯剂使用量、不同反应温度和不同HCl气体浓度对TiO2、CaO和CaTiO3脱氯效果的影响。结果显示,TiO2能在高温(800~1 000℃)、高HCl浓度(1 303.6~1 629.5 mg/m3)下获得较好的脱氯效果。与传统的脱氯剂CaO相比,TiO2更适合于高温烟气脱氯,其在1 000℃时的氯容(36.3 mg HCl/g TiO2)几乎是相同情况下的CaO氯容(9.3 mg HCl/g CaO)的4倍。而CaTiO3的脱氯效果不但受到自身分解效率的影响,还受到TiO2和CaO脱氯效果的影响,其脱氯效果较差。     

Acute and chronic toxicity of organophosphate monocrotophos to Daphnia magna

The acute and chronic toxicity of monocrotophos (MCP), the binary joint toxicity of MCP and bifenthrin (BF), and sodium dodecyl benzene sulfonate (SDBS) to Daphnia magna (D. magna) was evaluated. The 24 h-median effective concentration (24 h-EC₅₀) and 48 h-median lethal concentration (48 h-LC₅₀) of MCP towards D. magna were 161 and 388 μ g/L, respectively. In addition, the lowest-observed effective concentration (LOEC) and non-observed effective concentration (NOEC) of MCP to D. magna were 10 and 5 μ g/L, respectively. Furthermore, the chronic value (ChV) of MCP against D. magna was 7 μ g/L and the acute chronic ratio (ACR) was 55. The number of offspring per female and the intrinsic rate of natural increase (r) were identified as the parameters that were most sensitive to MCP. In addition, toxic unit (TU) analysis was employed to evaluate the joint toxicities. The calculated TU_mix values of binary equitoxic mixtures of MCP + BF and MCP + SDBS were 1.47 and 1.63, respectively, which suggests that both equitoxic mixtures exert a limited antagonistic effect. The results of this study revealed that the toxic threshold of MCP towards D. magna is higher than its reported highest residue (4 μ g/L) in the ordinary aquatic environment, and that concurrent exposure to BF or SDBS may exert a slight antagonistic effect.     

Enantioselectivity of racemic metolachlor and S-metolachlor in maize seedlings

Chiral herbicides may have enantioselective effects on plants. In this study, we assessed and compared the enantioselectivity of the chiral herbicides rac-metolachlor and S-metolachlor to maize seedlings. The superoxide dismutase activity (SOD) activity of roots and stem leaves treated by rac-metolachlor was 1.38 and 1.99 times that of roots and stem leaves treated by S-metolachlor. The peroxidase activity (POD) activity of roots and stem leaves was 1.48 and 2.79 times that of roots and stem leaves treated by S-metolachlor, respectively, while the catalase activity (CAT) activity was 4.77 and 8.37 times greater, respectively. The Hill reaction activity of leaves treated by rac-metolachlor were 1.45, 1.33, and 1.14 times those treated by S-metolachlor with treatments of 18.6, 37.2, and 74.4 μM. The differences observed between treatments of rac- and S-metolachlor were significant. Significant differences in maize seedling morphology were also observed between rac- and S-metolachlor treatments. The degradation rate of S-metolachlor in roots was greater than that of rac-metolachlor. The half-lives of rac- and S-metolachlor were 80.6 and 60.3 h at 18.6 μM; 119.5 and 90 h at 37.2 μM; and 169 and 164.8 h at 74.4 μM, respectively. Using the liquid chromatography-mass spectrometry method, hydroxymetolachlor, deschlorometolachlor and deschlorometolachlor propanol were considered to be possible metabolites. We determined the enantioselective toxicity of rac- and S-metolachlor to maize and speculated on the proposed metabolic pathway of metolachlor in maize roots. These results will help to develop an understanding of the proper application of rac- and S-metolachlor in crops, and give some information for environmental safety evaluation of rac- and S-metolachlor.     

The characteristics of nitrate removal by the psychrotolerant denitrifying bacterium Acinetobacter johnonii DBP-3, isolated from a low-temperature eutrophic body of water

A psychrotolerant denitrifying bacterial strain, DBP-3, was isolated from a eutrophic body of water by low-temperature-oriented acclimation culture. Based on its morphologicalandbiochemicalcharacteristics and 16S rDNA gene sequence, the bacterium was identified as belonging to the genus Acinetobacter and closely related to A. johnonii. The satisfactory growth of DBP-3 was observed at 10–30°C and pH 7–9. Strain DBP-3 was able to utilize three types of carbon sources (sodium acetate > sodium citrate > glucose) to support growth and denitrification. DBP-3 grew faster, but with lower nitrate removal efficiency and higher nitrite accumulation, under aerobic conditions than under anoxic conditions. DBP-3 was extremely susceptible to tetracycline and rifampicine and less sensitive to ampicillin and penicillin. The growth of DBP-3 was significantly affected by Hg (II), Cr (VI), Pb (II), Cd (II), and As (III) at 0.32, 0.63, 1.25, 2.5, and 25.0 mg L^?1, respectively. Interestingly, chromium (VI) significantly promoted DBP-3 growth at concentrations lower than 0.32 mg L^?1. These data may be helpful to support the use of strain DBP-3 in the purification of eutrophic water bodies at low temperatures.     

Water Content of Collected Aerosols in the South Coast and Southeast Desert Air Basins

Pollution prevention/waste minimization is a win-win-win situation for government, industry, and the public, which offers more than just protection of the environment for all. Industry gains from reduced capital and operating costs, reduced liabilities, cleaner and safer working conditions, conservation of energy and material resources, and the opportunity for government and industry to work together in a cooperative manner. However, a number of regulatory barriers exist which discourage pollution prevention/waste minimization. This paper provides examples from the aluminum, chemical, petroleum, and wood treating industries of how these regulatory barriers become disincentives. To promote pollution prevention/waste minimization, Congress and the U.S. EPA need to reexamine those RCRA provisions which support a command and control strategy that creates the barriers. The barriers include the distinction between value and valueless materials, offsite storage requirements prior to reuse/recycle, the “Derived from Rule”, the “Burning for Fuel Rule”, land ban technology standards, and RD&;D restrictions. A new RCRA Pollution Prevention/Waste Minimization subtitle is proposed to eliminate or minimize these barriers.     

A Survey of Nitrogen Dioxide Levels Measured Inside Mobile Homes

As part of the California Mobile Home Study, over 250 mobile homes from throughout the state were monitored for nitrogen dioxide (NO₂) concentrations. Week-long average measurements were taken with Palmes tubes in the kitchen and bedroom of each mobile home during the summer of 1984 and the winter of 1985. The study was conducted entirely by mail with the participants providing all the necessary information. Mobile homes using gas for cooking had significantly higher indoor NO₂ levels than those using electricity. Mobile homes located in the Los Angeles basin had significantly higher indoor NO₂ concentrations than did mobile homes in the rest of the state. Gas cooking, the inverse of the house volume and geographic location (as a surrogate of outdoor NO₂) were the most important variables identified by multiple linear regression.     

Variations in the Emissions of Volatile Organic Compounds from the Toner for a Specific Photocopier

ABSTRACT

A laboratory thermal desorption apparatus was used to measure emissions from a number of nominally identical photocopier toners—manufactured to meet the specifications of one specific model copier—when these toners were heated to fuser temperature (180-200 °C). The objective was to assess how potential volatile organic compound (VOC) emissions from the toner for a given copier can vary, depending upon the production run and the supplier. Tests were performed on a series of toner (and associated raw polymer feedstock) samples obtained directly from a toner manufacturer, representing two production runs using a nonvented extrusion process, and on toner cartridges purchased from two local retailers, representing three different production lots (histories unknown). The results showed that the retailer toners consistently had up to 350% higher emissions of some major compounds (expressed as |ig of compound emit-ted/g of toner), and up to 100% lower emissions of others, relative to the manufacturer toners (p ≤ 0.01). The manufacturer toners from one production run had emissions of certain compounds, and of total VOCs, that were modestly higher (13-18%) than those from the other run (p ≤ 0.01). The emission differences between the retailer and manufacturer toners are probably due to differences     

A Cost-Effective Weighing Chamber for Particulate Matter Filters

ABSTRACT

Particulate matter (PM) is a ubiquitous air pollutant that has been receiving increasing attention in recent years due in part to the association between PM and a number of adverse health outcomes, including mortality and increases in emergency room visits and respiratory symptoms, as well as exacerbation of asthma and decrements in lung function.^1-5 As a result, the ability to accurately sample ambient PM has become important, both to researchers and to regulatory agencies. The federal reference method for the determination of fine PM as PM_2.5 in the atmosphere recommends that particle-sampling filters be conditioned and weighed in an environment with constant temperature and relative humidity (RH).⁶ It is also recommended that vibration, electrostatic charges, and contamination of the filters from laboratory air be minimized to reduce variability in filter weight measurements. These controls have typically been maintained in small, environmentally controlled “cleanrooms.” As an alternative to constructing an elaborate cleanroom, we have designed, and presented in this paper, an inexpensive weighing chamber to maintain the necessary level of humidity control.