粉煤灰基层状金属氧化物对水中活性红X-3B的吸附

以粉煤灰(FA)为原料,采用共沉淀法制备了层状双金属氢氧化物(LDH)和层状金属氧化物(LMO,也称LDO),并采用XRD和BET技术进行了表征。比较了FA、LDH、LMO对活性红X-3B染料(X-3B)的吸附效果;考察了LMO吸附X-3B的影响因素,并探讨了吸附机理。XRD表征结果表明,LMO在吸附X-3B后重新恢复LDH层状结构。BET表征结果表明,LMO的比表面积大于LDH。吸附实验结果表明,3种吸附剂对X-3B吸附效果的优劣顺序为:LMOLDHFA;在初始X-3B质量浓度为50 mg/L、LMO投加量为2.0 g/L、吸附温度为25℃、吸附pH为7、吸附时间为30 min的条件下,X-3B去除率可达98.1%;LMO对X-3B的吸附符合Langmuir等温吸附方程,饱和吸附量为129.53 mg/g,且吸附过程可用准二级动力学方程描述。     

采用支持向量机算法优化电化学处理油田污水的工艺参数

采用支持向量机(SVM)算法,将Box-Behnken设计法与支持向量回归算法(SVR)实验参数优化软件相结合,优化电化学去除油田污水COD的工艺参数。通过量子粒子群算法对SVM算法参数进行优化,从建立的回归模型中找到工艺参数的全局最佳点:电解时间60 min,电解电流3 A,三维电极填充料中石英砂质量695 g。模型得到的COD理论最优去除率为92.48%,验证实验得到的COD去除率为91.43%。     

水环境中石油类物质分析方法探讨

在详述了国内外石油类分析方法的基础上,对各方法的适用范围、优缺点及可比性进行了深入分析,阐述了各类方法存在的共性问题,指出按照石油类物质毒性大小分别定量分析的方法将是未来的发展趋势。     

我国林业碳汇市场供需研究——以广东长隆碳汇造林项目为例

广东长隆碳汇造林项目作为我国首个获得国家发展和改革委员会签发的林业温室气体自愿减排(CCER)项目,对于我国林业碳汇参与应对气候变化具有重要的示范意义。本文对广东长隆碳汇造林项目进行了成本收益分析,发现林业碳汇交易价格被远远低估,从而使该项目不具备经济上的可复制性。为探究交易价格被低估的原因,本文考察了林业碳汇市场的供需关系,发现目前碳交易市场对林业碳汇CCER需求不足仅是表象,供需错配才是实质。首先,从需求侧来看,广东省碳排放配额设置过于宽松,缺乏林业碳汇CCER的接纳能力;其次,就供给侧而言,CCER的交易成本很高,且项目申报要求业主为企业法人,这严重限制了林业碳汇CCER的有效供给。鉴于以上问题,本文提出应同时从林业碳汇CCER的需求侧和供给侧着手改革。就需求侧而言,收紧广东省碳排放配额总量,并将林业碳汇CCER交易由补充机制改为配额管理。就供给侧而言,可以结合广东省推进林业碳普惠制度,将项目申报主体和交易主体放宽到独立法人和个人,广泛吸收民间资本、培育大型林业企业开展碳汇造林项目;降低碳汇项目进入门槛,根据省情制定方法学,简化签批手续。     

Preparation of biochar catalyst with saccharide and lignocellulose residues of corncob degradation for corncob hydrolysis into furfural

This paper presented a novel process for production of furfural by hydrothermal degradation of corncob over biochar catalyst, in which it was prepared with the recycling degradation solution and lignocellulosic solid residues. The biochar catalyst was papered by lignocellulose residues and concentrated saccharide solution, and then impregnated in 0.5 mol/L sulphuric acid at room temperature for 24 h assisted by the ultrasonic vibration. In the system of recycling, 8.8 % lignocellulose residues and 100 % concentrated saccharide solution from corncob hydrolysis have been recycled. Hydrolysis of corncob was carried out at 180 °C for duration of 170 min over the biochar catalyst. The experimental results have shown that the furfural yield of up to 37.75 % and overall corncob conversion rate of 62.00 % could be achieved under optimum operating conditions for the catalysts preparation and the corncob hydrolysis. It is believed that the acid density of 4.27 mmol/g of biochar catalyst makes the SO₃H groups cleave β-1,4 glycosidic linkages effectively and hydrolyze the cellulose and hemicellulose to water-soluble sugars, as well as to facilitate dehydration of xylose to give the product of furfural.     

Formation of persistent chlorinated aromatic compounds in simulated and real fly ash from iron ore sintering

Effects of carbon concentration and Cu additive in simulated fly ash (SFA) and real fly ash (RFA) on the formation of polychlorinated dibenzofurans (PCDFs), polychlorinated dibenzo-p-dioxins (PCDDs), chlorobenzenes, and polychlorinated biphenyls which were all regarded as persistent chlorinated aromatics in iron ore sintering were investigated. In the annealing process of SFA with various carbon contents, the yield of chlorinated aromatics and the I-TEQ obtained their maximum at 10 wt% carbon content. Active carbon in SFA acted as the carbon source as well as an adsorbent which led to higher production of PCDD/F in solid phase at 10 wt% carbon content. The increase of carbon content will be beneficial on the formation of 2,3,7,8-Chloro-substituted PCDF compared with 2,3,7,8-Chloro-substituted PCDD. In addition, the CuCl₂·2H₂O was a much more powerful catalyst in the formation of chlorinated aromatic compounds compared with elementary Cu, since it served as both a catalyst and a chlorine donor. However, the RFA behaved similarly with SFA with elementary Cu in the formation of chlorinated aromatic compounds. The effect of carbon content and copper additives on formation of 2,3,7,8-chloro-substituted congeners displayed similar characteristics with the tetra- to octa-PCDD/F isomers and even the total PCDD/Fs.     

The implementation of a measurement system for brushless DC motor parameters

Most of the energy conversion in industrial devices and equipment is completed by the motor. The acquirement of motor parameters becomes very important for designing the motor drives. The aim of this paper is to design and implement a motor measurement system. Through the processing of an Advanced RISC Machines (ARM) microcontroller, the various parameters of motors such as input voltage, input current, input power, motor speed, and motor torque can be obtained. Consequently, the torque constant, load torque, viscous friction, and the inertia of the motor are calculated and achieved. The motor parameters can be commanded and displayed in the designed human interface of a PC via USB communication. The hardware system designed in this system includes an ARM microcontroller, an inverter, a voltage sensor, a current sensor, a torque sensor, and power supply. The software programming is developed under the Visual Studio 2012 environment development platform using the C language. Finally, the prototype of the motor measurement system is completed and verified. The experimental results for the motor parameters and torque/speed characteristic are demonstrated and show the feasibility of the complete designed system.     

Zr掺杂TiO_2介孔材料光催化降解头孢氨苄

采用固相合成法制备了Zr掺杂TiO_2(Zr-TiO_2),运用XRD技术对其进行了表征,并将其用于水中头孢氨苄的光催化降解,通过单因素实验及正交实验优化了光催化反应条件。结果表明:制备的Zr-TiO_2为锐钛矿型介孔材料,孔径约为8.12 nm;各因素对头孢氨苄去除率的影响由大到小依次为光照时间、Zr-TiO_2投加量、初始头孢氨苄质量浓度;在Zr-TiO_2投加量为1.5 g/L、初始头孢氨苄质量浓度为10 mg/L、溶液pH为7.0、光照(300 W UV)时间为1.5 h的优化条件下,头孢氨苄去除率高达99.46%;Zr-TiO_2光催化剂的重复使用性能良好。     

超疏水沸石咪唑酯骨架材料ZIF-90的制备及其气体吸附性能

以自制沸石咪唑酯骨架材料ZIF-90为原料,自制2,3,4,5,6-五氟苄胺为修饰剂,通过后修饰法制备了超疏水ZIF-90,采用SEM、XRD、FTIR等技术对其进行了表征,并进行了气体吸附性能测试。表征结果显示:制备的超疏水ZIF-90晶体结构和形貌良好;水接触角高达152.1°;修饰剂分子与ZIF-90晶体上的自由醛基成功发生缩胺反应。气体吸附实验结果表明:当相对压力小于0.02时,超疏水ZIF-90的CO_2吸附量较ZIF-90明显增大,CO_2/N_2和CO_2/CH_4的理想吸附选择系数由修饰前的15.76和4.88分别提升至33.28和17.13;超疏水ZIF-90具有优异的憎水性能。     

臭氧氧化法降解聚氯乙烯离心母液废水中3种有机物

以聚氯乙烯离心母液废水中含量较高的3种有机物(聚乙烯醇、异辛醇和α-甲基苯乙烯)作为目标物,考察臭氧氧化工艺对3种有机物的去除效果,同时考察反应时间、臭氧投加量和初始pH对处理效果的影响。实验结果表明,臭氧氧化处理3种废水的最佳反应时间和臭氧投加量分别为:聚乙烯醇25 min,136 mg/L;异辛醇60min,312 mg/L;α-甲基苯乙烯60 min,32 mg/L。在此条件下,3种有机物的去除率分别为98%、85%和95%。此外,碱性条件有助于臭氧氧化工艺对3种有机物的降解。产物分析结果表明,经臭氧氧化,聚乙烯醇断链后进一步反应生成了草酸单乙酯,异辛醇和α-甲基苯乙烯分别生成了和苯乙酮。