Remediation aspect of microbial changes of plant rhizosphere in mercury contaminated soil

Phytoremediation, an approach that uses plants to remediate contaminated soil through degradation, stabilization or accumulation, may provide an efficient solution to some mercury contamination problems. This paper presents growth chamber experiments that tested the ability of plant species to stabilize mercury in soil. Several indigenous herbaceous species and Salix viminalis were grown in soil collected from a mercury-contaminated site in southern Poland. The uptake and distribution of mercury by these plants were investigated, and the growth and vitality of the plants through a part of one vegetative cycle were assessed. The highest concentrations of mercury were found at the roots, but translocation to the aerial part also occurred. Most of the plant species tested displayed good growth on mercury contaminated soil and sustained a rich microbial population in the rhizosphere. The microbial populations of root-free soil and rhizosphere soil from all species were also examined. An inverse correlation between the number of sulfur amino acid decomposing bacteria and root mercury content was observed. These results indicate the potential for using some species of plants to treat mercury contaminated soil through stabilization rather than extraction. The present investigation proposes a practical cost-effective temporary solution for phytostabilization of soil with moderate mercury contamination as well as the basis for plant selection.     

A GIS-based Study for Optimizing the Total Emission Control Strategy in Lanzhou City

A geographic information system (GIS)-based approach with spatial analysis advantages was developed to optimize the total emission control scheme on air pollution in Lanzhou, combined with Models-3 modeling system and a linear programming model. GIS system is mainly used for establishing a multifactor assessment model to quantitatively divide environmental functional zone, and also used for selecting control sites in linear programming model. The results show that most of the urban area belongs to the second type of function, which is 122.8 km² occupying about 76.5% and the third type of about 32.9 km² occupying 20.5%. To reach the air quality up to the national standard in the entire control area, some large-emission factories need to cut emissions from 19% to 27%. For small but low-emission height sources, the cut may be as high 40%. The improvement of the ecological environment is urgently needed for controlling the background particle pollution in Lanzhou city.     

Study on Management and Control of Nonpoint Source Pollution from Urban Surface Runoff

Urbanization is the dominant form of land-use change in terms of impacts on water quality, hydrology, physical properties of watersheds and their nonpoint source （NPS） pollution po-tential at present. Urbanization has changed the source, process and sink of urban NPS pollution, especially raised the pollution load of urban runoff NPS in receiving water. Urban runoff pollution is a hot spot of research on NPS. This paper analyzed type, source and harm of the NPS pollutants of urban runoff and its influence on the receiving water. Through estimating NPS pollution load of urban runoff and summarizing the law and characteristics of urban runoff NPS systemically, study on management and control of urban runoff NPS pollution was focused on the application of BMPs （best management practices）. It is a fresh methodology that management and control on NPS pollution from urban surface runoff was analyzed by methods of landscape ecology, environmental economics and environmental management. The paper provided a scientific reference for mitigating urban water environment pressure and an effective method for management and control of NPS pollution from urban surface runoff.     

Vacuum pyrolysis of waste tires with basic additives

Granules of waste tires were pyrolyzed under vacuum (3.5-10kPa) conditions, and the effects of temperature and basic additives (Na(2)CO(3), NaOH) on the properties of pyrolysis were thoroughly investigated. It was obvious that with or without basic additives, pyrolysis oil yield increased gradually to a maximum and subsequently decreased with a temperature increase from 450 degrees C to 600 degrees C, irrespective of the addition of basic additives to the reactor. The addition of NaOH facilitated pyrolysis dramatically, as a maximal pyrolysis oil yield of about 48wt% was achieved at 550 degrees C without the addition of basic additives, while a maximal pyrolysis oil yield of about 50wt% was achieved at 480 degrees C by adding 3wt% (w/w, powder/waste tire granules) of NaOH powder. The composition analysis of pyrolytic naphtha (i.b.p. (initial boiling point) approximately 205 degrees C) distilled from pyrolysis oil showed that more dl-limonene was obtained with basic additives and the maximal content of dl-limonene in pyrolysis oil was 12.39wt%, which is a valuable and widely-used fine chemical. However, no improvement in pyrolysis was observed with Na(2)CO(3) addition. Pyrolysis gas was mainly composed of H(2), CO, CH(4), CO(2), C(2)H(4) and C(2)H(6). Pyrolytic char had a surface area comparable to commercial carbon black, but its proportion of ash (above 11.5wt%) was much higher.     

高校文书档案立卷改革的探索与应用

传统的立卷程序繁琐复杂,既浪费了人力、物力和财力,利用效果也不理想。随着社会的发展,传统的文书立卷方法已不适应档案管理现代化的需要,必须转变观念,把工作重点由“重藏轻用”转移到“简化管理、强化检索、重在利用”的新思路上来。新的规则取消了案卷,以件为单位进行整理归档,简单、易学、实用,有利于档案的保护、查找和利用。在新规则的实践过程中,档案工作者也需灵活掌握,改进工作方法。     

Photocatalytic degradation of lignin using Pt/TiO2 as the catalyst

Photocatalytic degradation of lignin was studied with the use of catalysts TiO(2) and Pt/TiO(2). The influence of several experimental parameters, i.e. pH, catalyst dosage and illumination on lignin degradation was investigated. The results showed that application of UV irradiation alone has almost no effect on the reduction of dissolved organic carbon (DOC) and American Dye Manufacture Institute value (ADMI). However, the addition of TiO(2) and Pt/TiO(2) reduced the original DOC (251 mg l(-1)) by more than 40% within 30 min of treatment and the reaction can be simulated with pseudo-first order kinetics. Rapid degradation of lignin was observed in acidic solution using either TiO(2) or Pt/TiO(2) as the catalyst compared to high pH cases. The content of Pt in the Pt/TiO(2) catalyst is 1%. In addition, too much catalyst addition has not increased the DOC and ADMI reduction proportionally. The investigation also indicated that the photocatalytic degradation rates could be enhanced 1-6 times faster after doping TiO(2) with Pt in different pH cases. A modified Nernst type model was adopted to simulate the decoloring process using TiO(2) and Pt/TiO(2) based on the profiles of oxidation reduction potential during the photocatalytic reaction. The developed equation can be used to predict the color removal efficiency of lignin wastewater by the photocatalytic process.     

Kinetic degradation processes of butyl- and phenyltins in soils

The degradation of organotin compounds (OTC) in agricultural and forest soils is studied in sandy soil samples. Individual experiments involving the three butyl- and the three phenyltins were carried out during 90 d in controlled conditions (darkness, 28 degrees C, aerobic conditions, 13% moisture) and with spiking concentration representative of environmental levels (20-50 micrg(Sn) kg(-1)). After the validation of first-order degradation kinetic model, mechanisms involved throughout the study were considered. Degradation pathways are proposed for butyl- and phenyltins and discussed according to literature data. The degradation of mono- (MBT, MPhT), di-organotins (DBT, DPhT) and TBT is clearly identified as a single successive loss of an organic group whereas TPhT is directly degraded to MPhT. The half-life times were dependent on their substitution degree, ranging from 24 (TPhT) to 220 (MBT) d. The less substituted the OTC is, the more persistent it is. In the range 4.3-5.7, pH does not seem to influence OTC degradation under the present operating conditions. Finally this study shows the significant persistence in soil samples in our experimental conditions for most of studied organotins and highlights the potential impact on soil quality.     

A novel sustainable decision making model for municipal solid waste management

This paper reviews several models developed to support decision making in municipal solid waste management (MSWM). The concepts underlying sustainable MSWM models can be divided into two categories: one incorporates social factors into decision making methods, and the other includes public participation in the decision-making process. The public is only apprised or takes part in discussion, and has little effect on decision making in most research efforts. Few studies have considered public participation in the decision-making process, and the methods have sought to strike a compromise between concerned criteria, not between stakeholders. However, the source of the conflict arises from the stakeholders' complex web of value. Such conflict affects the feasibility of implementing any decision. The purpose of this study is to develop a sustainable decision making model for MSWM to overcome these shortcomings. The proposed model combines multicriteria decision making (MCDM) and a consensus analysis model (CAM). The CAM is built up to aid in decision-making when MCDM methods are utilized and, subsequently, a novel sustainable decision making model for MSWM is developed. The main feature of CAM is the assessment of the degree of consensus between stakeholders for particular alternatives. A case study for food waste management in Taiwan is presented to demonstrate the practicality of this model.     

拮抗菌对黄瓜枯萎病菌的室内生物活性

测定了从沤肥浸渍液和土壤中分离并筛选得到对黄瓜枯萎病菌的室内生物活性的6个菌株,编号为94－I、94－Ⅱ、94－Ⅲ、96－Ⅰ和98－Ⅱ,测定其孢子悬浮培养16h时对黄瓜枯萎菌的抑制率分别为48．29％、0．00％、60．69％、39．28％、61．29％和72．32％,孢子和菌丝有的变畸形并产生大泡囊;平皿拮抗试验表明,其活体浓度为50％时对黄瓜枯萎病菌的抑制率最大分别为74．52％、83．27％、90．60％、88．59％、89．35％和94．30％;而其相同浓度高压蒸汽灭活后的代谢产物对黄瓜枯萎病菌的抑制率最大分别为33．215、52．22％、62．84％、46．57％、47．61％和70．34％。     

Identification of Pollution Source of Cadmium in Soil. Application of Material Flow Analysis and A Case Study in Taiwan (11 pp)

Background Since the 1970s, at least 200 hectares (ha) of farmland has been polluted by the heavy metal cadmium (Cd).Consequently, the Cd pollution has led to contaminate the rice production and caused acute social panic. According to the recent investigation results performed by the Taiwan Environmental Protection Administration (TEPA), it is indicated that most of the Cd pollution incidents in Taiwan resulted from the wastewater discharge of stearate Cd factories. To prevent the Cd pollution incidents from spreading, the TEPA has either forced these factories to close down or assisted them in improving their production processes since the 1980s. Unfortunately, accidental incidents of Cd pollution still emerge in an endless stream, despite the strict governmental controls placed on these questionable factories. Whether this pollution has resulted from undetected or hidden pollution sources stemming from two decades ago or comes from some new source, will be an outstanding issue. Therefore, this study attempts to identify the pollution sources of Cd in soil in Taiwan as well as to find the solution to the above-mentioned, outstanding issue by way of a methodology termed Material Flow Analysis (MFA). Method logy. The MFA has proved to be a useful tool on providing quantitative information of the flow of substances through an economic to an environmental system. Based upon the supply-and-demand theory of MFA, researchers have successfully conducted an overview of the use of materials in many industries, the construction industry being one of these. Therefore, this study tries to establish a set of analytical processes by way of MFA for identifying the pollution source of Cd in soil in Taiwan. In addition, the spirit of Life Cycle Analysis (LCA) technique was also employed to identify the materials, and products should be ignored as a crucial pollution source in this study. Results and Discussion According to the MFA methodology applied in this study and on the basis of related studies performed by Taiwanese governmental authorities, we arrive at the following analysis results: (1) the total amount of Cd from the economic perspective of material and product flow was approximately 441.2 tons; (2) the wastewater directly discharged into irrigation water can be concluded to be the major pollution route of Cd in farmland soil in Taiwan; (3) material plastic stabilizer (cadmium oxide, CdO), Zn-Pd compounds and Cu compounds should be the crucial pollution sources to contaminate environment through the route of wastewater in Cd flow analysis; (4) the crucial pollution sources to contaminate environment through the route of wastewater in Cd flow analysis were five factories, Coin, Jili, Taiwan Dye, Guangzheng and Mingguan, and they were all categorized as stearate Cd industries; (5) the typical source of the Cd pollution in soil in Changhua County through the pollution route of wastewater should be the metal surfacing process industries. Conclusions This study proved that MFA can be a good tool for identifying Cd flow as well as for recognizing the crux of the problem concerning incidents of Cd pollution. This study led to the conclusion that the causal relationship between farmland pollution caused by Cd and stearate Cd factories in Taiwan seemed quite close by way of MFA methodology. In addition, this study also found that the wastewater discharged from a single metal surfacing process factory will not cause remarkable farmland pollution. However, the wastewater simultaneously discharged from a group of pollution factories can result in a significant pollution incident. Recommendations and Outlook This case study is only a small contribution to the understanding of the toxic material flow related to Cd in the environment. This study recommends that Taiwanese governmental authorities should not deal with problems on an ad hoc basis, but should instead deal with Cd pollution problems overall employing control measures. Finally, the more accurate information or data we can collect, the more reliable results we can identify. Therefore, the quality and quantity of related data used in this MFA model should be closely scrutinized in order to ensure the most correct and comprehensive investigation on the toxic material flow.