Butyltin levels in several Portuguese coastal areas

This work aimed to report present levels (2007–2008 sampling) of tri- (TBT), di- (DBT), and monobutyltin (MBT) in surface sediments from 11 Portuguese coastal sites and discuss the evolution of BTs contamination in the last two decades. All the samples revealed quantifiable values of TBT, DBT, and MBT with total butyltin concentrations between 1 and 565 ng/g (of Sn in dry sediment). Maximum level of TBT, 66 ng/g, was observed in Sado estuary, at Lisnave site, in the proximity of a big shipyard. MBT decreased site by site by the same order as DBT and TBT did, but its concentrations were much higher in many cases, denoting that TBT contamination was much higher in the past. A comparison with the available previous data confirmed a marked decrease of TBT contamination all over the last years, indicating that the main sources of TBT in Portuguese coastwise stopped effectively.     

Higher Plants As Bioindicators Of Sulphur Dioxide Emissions In Urban Environments

The evaluation of certain vascular plants that grow in the city of Madrid as biomonitors of SO₂ air pollution in urban environments has been carried out. Total concentration of sulphur in leaves of the chosen higher plants as well as other parameters in close relation to this contaminant (visible injury symptoms, chlorophyll a- and b-content and peroxidase activity) have been determined in order to study the spatial distribution and temporal changes in SO₂ deposition. Results obtained show that coniferous species such as Pinus pinea, were more sensitive to SO₂ atmospheric concentration than leafy species as Quercux ilex subspecies ballota and, in the same way, bush species, such asPyracantha coccinea and Nerium oleander, were more sensitive than wooded species, such as Cedrus deodaraandPinus pinea, respectively. There is a higher accumulation of sulphur in vegetable species located near highways and dense traffic incidence roads and near areas with high density of population. The minimum values for accumulation of SO₂ were registered in winter and spring seasons (from January to April) due to the vegetative stop; while maximum values are obtained during the summer season (from June to September), due to the stoma opening. The highest increments in sulphur concentration, calculated as the difference between two consecutive months, are obtained in May and June for all considered species except forCedrus deodara and Pyracantha coccinea, both species have few seasonal changes during the whole year. Some species are more sensitive to natural washing than others, showing a decrease in sulphur concentration after rainfall periods.     

Chemical defense of the mint plant, Teucrium marum (Labiatae)

Summary. The mint plant, Teucrium marum (family Labiatae), sometimes called cat thyme, contains two methylcyclopentanoid monoterpenes, dolichodial and teucrein. The former compound is potently anti-insectan. It is repellent to ants (Monomorium pharaonis) and induces preening reflexes in flies (Phormia regina) and cockroaches (Periplaneta americana). Evidence is presented suggesting that dolichodial, which is presumed to be the plant's chief defensive agent, is stored in the tiny epidermal capsules that beset the leaves. It is only when the leaves are injured (and the capsules ruptured) that the leaves become repellent. Teucrein, in contrast, has no anti-insectan potency. It is present predominantly in the leaf buds, unlike dolichodial, which is present mostly in mature leaves. It is argued that teucrein is the storage compound from which dolichodial is generated during leaf development.     

The influence of prey distribution on the foraging strategy of the lizard Oligosoma grande (Reptilia: Scincidae)

The grand skink, Oligosoma grande, is a diurnal rock-dwelling lizard from the tussock grasslands of Central Otago, New Zealand, whose diet includes a variety of arthropods and fruit. We conducted a field experiment to examine the influence of prey distribution on foraging behavior and spacing patterns. On sites where prey distribution was unaltered (control sites), males and females differed in diet and foraging behavior. Most male feeding attempts were directed at large strong-flying insects, and males used a saltatory search pattern that involved relatively infrequent moves of long duration. Females spent more effort catching small weak-flying insects and visiting fruiting plants. Their search behavior involved frequent moves of short duration. The placement of meat-bait on experimental sites led to a redistribution of large flies without influencing other prey types. Experimental females switched foraging strategy by adopting a search pattern of relatively infrequent moves of long duration, increasing the frequency of attempts to capture large prey, and reducing the importance of fruit in their diet. The experimental manipulation appeared to influence space use. On control sites, both sexes had comparably sized home ranges. On experimental sites, male home ranges were significantly larger than female home ranges. Received: 3 November 1997 / Accepted after revision: 13 December 1998     

Remediation of PCB‐Contaminated Soil Using Extraction and Destruction: Bench‐Scale Test

Polychlorinated biphenyls (PCBs) are a persistent environmental issue worldwide. This study summarizes the results obtained from a bench‐scale test of remediating PCB‐impacted soil. The research aimed to evaluate the effectiveness of extracting the PCB Aroclor 1260 from soil, transferring it to a liquid matrix, and then treating the PCB‐containing liquid using an Activated Metal Treatment System, a technology developed by NASA based on zero valent magnesium (ZVMg). The soil was from a former electrical plant area impacted by PCBs. The initial concentration of untreated soil contained an average of 4.7 ± 0.15 mg/kg of Aroclor 1260. The results showed that the mass transfer phenomena is possible using ethanol as a liquid matrix, reaching transfer results up to 93 percent. The ZVMg enabled the destruction of the Aroclor 1260, which reached 20 percent without any buildup of undesirable by‐products, such as less chlorinated PCBs.  ©2016 Wiley Periodicals, Inc.     

Effect of fly ash addition on the removal of hydrogen sulfide from biogas and air on sewage sludge-based composite adsorbents

Desulfurization adsorbents were prepared from the mixtures of various compositions of New York City sewage sludge and fly ashes from SASOL, South Africa, by pyrolysis at 950 degrees C. The resulting materials were used as adsorbents of hydrogen sulfide from simulated dry digester gas mixture or moist air. The adsorbents before and after H(2)S removal were characterized using adsorption of nitrogen, elemental analysis, pH measurements, XRF, XRD, and thermal analysis. It was found that the addition of fly ash decreases the desulfurization capacity in comparison with the sewage sludge-based materials. The extent of this decrease depends on the type of ash, its content and the composition of challenging gas. Although the presence of CO(2) deactivates some adsorption sites to various degrees depending on the sample composition, the addition of ashes has a more detrimental effect when the adsorbents are used to remove hydrogen sulfide from air. This is likely the result of hydrophobicity of ashes since the H(2)S removal capacity was found to be strongly dependent on the reactivity towards water/water adsorption. On the other hand, the addition of ashes strongly decreases the porosity of materials where sulfur, as a product of hydrogen sulfide oxidation, can be stored.     

One-Component Spray Polyurethane Foam from Liquefied Pinewood Polyols: Pursuing Eco-Friendly Materials

The use of petroleum-derived products should be avoided regarding the principles of green and sustainable chemistry. The work reported herein, is aimed at the liquefaction of pine shavings for the production of an environmentally-friendly polyol suitable to be used in the formulations of sprayable polyurethane foams. The biopolyols were obtained in high yield and were used to replace those derived from fossil sources, to produce more “greener” polyurethane foams and therefore, less dependent on petroleum sources, since the polyol component was substituted by products resulting from biomass liquefaction. The partial and fully exchange of the polyols was accomplished, and the results compared with a reference foam. The foams were afterward, chemical, physical, morphological, and mechanically characterized. The complete replacement of polyether polyol and polyol polyester has presented some similar characteristics as that used as a reference, validating that the path chosen for the development of more sustainable materials is on the right track for the contribution to a cleaner world.     

Physical Properties, Photo- and Bio-degradation of Baked Foams Based on Cassava Starch, Sugarcane Bagasse Fibers and Montmorillonite

The objectives of this work were to develop biodegradable trays from cassava starch, sugarcane fibers and Na-montmorillonite (Na-MMT) using a baking process and to study the effects of these components on the physical properties, photo- and bio-degradation of the trays. The sample F20 (produced with 20 g fiber/100 g formulation) showed the maximum yield production (100 %). All formulations resulted in well-shaped trays with densities between 0.1941 and 0.2966 g/cm³. The addition of fibers and Na-MMT resulted in less dense and less rigid trays compared to control samples (only starch). The studied processing conditions resulted in good nanoclay dispersion, leading to the formation of an exfoliated structure. The evaluation of the photo-degradation stability of the trays under UV exposure for 336 h showed that a sample produced with a specific combination of fiber and nanoclay (20 g fiber and 5 g nanoclay/100 g formulation) had the highest loss in stress at break (91 %). Biodegradation assays showed that Control trays (starch) and F20 (20 g fiber/100 g formulation) lost a greater percentage of their weight after 90 days of incubation in soil, with losses of up to 85.50 and 82.70 %, respectively.     

Co-treatment of fruit and vegetable waste in sludge digesters. An analysis of the relationship among bio-methane generation,process stability and digestate phytotoxicity

The co-digestion of a variable amount of fruit and vegetable waste in a waste mixed sludge digester was investigated using a pilot scale apparatus. The organic loading rate (OLR) was increased from 1.46 kg VS/m³ day to 2.8 kg VS/m³ day. The hydraulic retention time was reduced from 14 days to about 10 days. Specific bio-methane production increased from about 90 NL/kg VS to the maximum value of about 430 NL/kg VS when OLR was increased from 1.46 kg VS/m³ day to 2.1 kg VS/m³ day. A higher OLR caused an excessive reduction in the hydraulic retention time, enhancing microorganism wash out. Process stability evaluated by the total volatile fatty acids concentration (mg/l) to the alkalinity buffer capacity (eq. mg/l CaCO₃) ratio (i.e. FOS/TAC) criterion was <0.1 indicating high stability for OLR <2.46 kg VS/m³ day. For higher OLR, FOS/TAC increased rapidly. Residual phytotoxicty of the digestate evaluated by the germination index (GI) (%) was quite constant for OLR < 2.46 kg VS/m³ day, which is lower than the 60% limit, indicating an acceptable toxicity level for crops. For OLR > 2.46 kg VS/m³ day, GI decreased rapidly. This corresponding trend between FOS/TAC and GI was further investigated by the definition of the GI ratio (GIR) parameter. Comparison between GIR and FOS/TAC suggests that GI could be a suitable criterion for evaluating process stability.     

Enhancing submerged coastal constructions by incorporating multifunctional purposes

Surfing has becoming more and more attractive in the past few decades, constituting nowadays an important source of revenue for many countries with extensive coastlines. For this purpose and also for environmental reasons, the conventional ways of protecting a coastline appear to entail some disadvantages. An innovative and interesting way of improving surfing capacities and contributing to protect a local coastal zone is by means of multifunctional artificial reefs. A multifunctional artificial reef (MFAR) is a submerged structure that serves several purposes; in particular, it may enhance the surfing possibilities and the environmental value of the local area. This structure has some promising new aspects, too: first, it provides an unimpaired visual amenity; second, it offers tourist and economic benefits by improving the surfing conditions; third, it can enhance the environmental value of the area where it is built, and fourth, if designed properly, the down drift erosion can be minimal. An appropriate reef design in terms of ‘surfability’, i.e. the possibility to surf a wave, for the Leirosa beach, located to the south of Figueira da Foz, midway along Portugal’s West Atlantic coast, has been investigated. In order to achieve the best design several steps were conducted. First, the performance of the Boussinesq-type COULWAVE model is tested with experimental data. Next, this numerical model is used to define the best values for three design parameters: reef angle; geometry of the reef (without or with a platform), and horizontal dimensions for the appropriate geometry. A preliminary design was achieved step by step, making use of the theory and of the state of the art of multifunctional reefs. This reef geometry is used in the numerical study. In terms of ‘surfability’ and for the conditions of the local coastline of Leirosa, the following values were found for the main parameters: a reef angle of 66°; a structure height of 3.20 m; a reef geometry composed of a delta without a platform; a reef submergence of 1.50 m, and a structure seaward slope of 1:10.