高铝粉煤灰提取氧化铝后硅钙渣用作水泥混合材

为了使高铝粉煤灰提取氧化铝后所产生的硅钙渣被大量的用作水泥混合材,通过水泥强度、水化放热和干缩性实验研究了原状硅钙渣和脱碱硅钙渣对水泥强度和稳定性的影响。结果表明,当硅钙渣掺量达30%时,硅钙渣水泥强度仍可满足P·C 32.5水泥要求。且随硅钙渣掺入量的增加,水泥早期水化放热速率增加的同时水泥累计水化放热量和干缩率还会显著降低。与原状硅钙渣相比,在同等掺量的情况下,脱碱硅钙渣更有利于保持水泥强度,降低其水化热和改善干缩性。     

Fenton法处理垃圾渗滤液MBR-NF浓缩液

采用Fenton法处理MBR-NF浓缩液,考察了FeSO4·7H2O投加量、n(H2O2)/n(Fe2+)投加比、初始pH对渗滤液MBR-NF浓缩液处理效果的影响,并在最佳实验条件下,探讨浓缩液富里酸(FA)、亲水性有机物(HyI)组分在Fenton氧化前后组成的变化。研究结果表明,在FeSO4·7H2O投加量为0.055 mol/L、n(H2O2)/n(Fe2+)投加比为4、初始pH为7.58时,对COD、腐植酸(UV254)、色度(CN)的去除率分别为79.6%、93.7%和97.8%。Fenton氧化后,浓缩液中有机物组分含量发生了较大变化,腐植酸含量下降,HyI成为渗滤液溶解性有机物主要成分。紫外-可见光谱表明,Fenton法对FA去除效果较好,而对HyI氧化效果较差;傅立叶红外光谱显示,经Fenton氧化后,FA的结构发生了明显变化,而HyI则变化不明显。     

A full-scale sequencing batch reactor system for swine wastewater treatment

A full-scale sequencing batch reactor (SBR) system was evaluated for its ability to remove carbon and nitrogen from swine wastewater. The SBR was operated on four, six-hour cycles each day, with each cycle consisting of 4.5 hours of “React,” 0.75 hours of “Settling”, 0.75 hours for “Draw” and “Fill.” Within each cycle, an amount of wastewater equivalent to about 5% of the reactor volume (5,500 litres) was removed and added. The SBR system was able to remove 82% of biochemical oxygen demand (BOD) and more than 75% of nitrogen. Even though the SBR effluent, with an average effluent BOD₅ of about 588 mg L^{? 1}, did not meet the discharge criteria, it enabled a reduction of the land base required for land application of swine wastewater by about 75%. Results indicated that the SBR system was a viable method for the treatment of swine wastewater.     

Inorganic Acid Emission Factors of Semiconductor Manufacturing Processes

Abstract

A huge amount of inorganic acids can be produced and emitted with waste gases from integrated circuit manufacturing processes such as cleaning and etching. Emission of inorganic acids from selected semiconductor factories was measured in this study. The sampling of the inorganic acids was based on the porous metal denuders, and samples were then analyzed by ion chromatography. The amount of chemical usage was adopted from the data that were reported to the Environmental Protection Bureau in Hsin-chu County according to the Taiwan Environmental Protection Agency regulation. The emission factor is defined as the emission rate (kg/month) divided by the amount of chemical usage (L/month). Emission factors of three inorganic acids (i.e., hydrofluoric acid [HF], hydrochloric acid [HQ], and sulfuric acid [H₂SO₄]) were estimated by the same method. The emission factors of HF and HCl were determined to be 0.0075 kg/L (coefficient of variation [CV] = 60.7%, n = 80) and 0.0096 kg/L (CV = 68.2%, n = 91), respectively. Linear regression equations are proposed to fit the data with correlation coefficient square (R²) = 0.82 and 0.9, respectively. The emission factor of H₂SO₄, which is in the droplet form, was determined to be 0.0016 kg/L (CV = 99.2%, n = 107), and its R² was 0.84. The emission profiles of gaseous inorganic acids show that HF is the dominant chemical in most of the fabricators.     

Predicting Cutoff Aerodynamic Diameter and Sharpness of Single Round-Nozzle Impactors with a Finite Impaction Plate Diameter

Abstract

This investigation numerically examined the cutoff aerodynamic diameter (da₅₀) and the sharpness (GSD) of the particle collection efficiency curve of impactors with a finite impaction plate diameter. Results revealed that the inertial impactors have a limited cutoff aerodynamic diameter at different air velocities. The extreme value of the cutoff aerodynamic diameter increases with the nozzle diameter (W)/the plate diameter (D_c). The computed da₅₀/D_c values of the impactors increase with W/D_c at various Reynolds numbers (Re) and with the nozzle-toplate distance (S)/D_c when Re is 100. The value of GSD slightly increases with W/D_c for Re of 10 and 100, although the effect of S/D_c on GSD is not evident at various Res. The particle collection efficiency curve of the impactor with a lower Re is less sharp than that with a high Re at various W/D_c and S/D_c values. Statistical equations closely fitted the obtained numerical results for Res of 10–3000. The equations are useful for directly calculating the cutoff aerodynamic diameter and the sharpness of the particle collection efficiency curve for single round-nozzle impactors with a finite impaction D_c.     

Decomposition of Gas Phase 1,3-Butadiene by Ultraviolet/Ozone Process

Abstract

A pilot-scale plug-flow reactor was built to investigate its performance in treating airborne 1,3-butadiene (BD) via ozonation (O₃) and ultraviolet (UV)/O₃ technologies. Governing factors, such as the initial molar ratio of ozone to BD, UV volumetric electric input power, and moisture content in the influent airstream, were investigated. Experiments were conducted at an influent BD concentration of ～50 ppm, an ambient temperature of 26 °C, and a gas retention time of 85 sec. Results show that an initial molar ratio of ozone to BD of 3.5 and 2 sufficed to obtain BD decompositions of >90% for ozonation and UV/O₃, respectively. The UV irradiance did not directly promote the decomposition of BD, rather, it played a role in promoting the production of secondary oxidants, such as hydroxyl radicals. Kinetic analyses indicate that both types of BD decomposition are peudo–first-order with respect to BD concentrations. Moisture content (relative humidity = 40–99%) and UV volumetric electric input power (0.147 and 0.294 W/L) are both factors that weakly affect the rate of BD decomposition. Economic evaluation factors, including both energy of ozone production and UV electric input power, were also estimated.     

Influence of particle location on the number of charges per charged nanoparticle at the outlet of a needle charger

This study has investigated numerically the influence of particle location on the number of charges per charged particle in the 10–40 nm size range at the outlet of a needle charger by simulating flow field, electric field, particle charging, and particle trajectory at various conditions. The results show that the total (i.e., diffusion + field charging) number of charges per particle increase with decreasing ratio values of radial location at the outlet of the charger due to the particle position close to the needle tip. It has also been shown that in the outlet region of the charger there is a critical radial location at which the number of charges per particle is a maximum; this critical radial location represents the point at which the charged particle trajectory becomes closest to the needle electrode. The maximum value of number of charges increases with increasing Reynolds number and slightly increases with decreasing applied voltage for particle diameter larger than 20 nm. The maximum number of charges per charged nanoparticle increases with increasing particle diameter. In addition, the minimum ratio value of radial particle location decreases with increasing Reynolds number for various particle diameters.

Implications: In this work, the influence of particle location on the number of charges per charged nanoparticle at the outlet of a needle charger has been investigated using numerical models under different conditions. The results demonstrate that the radial location affects the number of charges per particle at the outlet of the charger. The maximum number of charges increases with increasing particle diameter, and the minimum ratio value of radial particle location decreases with increasing Reynolds number. The numerical models explain and quantify the number of charges on the charged particle in the 10–40 nm size range from the outlet of the needle charger at various conditions.     

创意产业集聚区外部交往空间规划探索——“心理-行为-空间”互动视角下的实证研究

创意产业集聚区在促进创意产业发展、优化城市空间结构等方面具有重要意义,而以满足创意阶层特征和需求的创意产业集聚区内部公共空间规划的研究相对较少。从创意阶层交往的“心理-行为-空间”这一互动视角出发,选取南京具有代表性的“创意东8区”为研究对象,通过调查问卷、深入访谈和实地观察对创意阶层的“交往心理-交往行为-交往空间”进行了研究。在此基础上,从人口交往空间、中心交往空间、节点交往空间、道路交往空间等方面提出符合创意阶层心理和行为特征,并能促进交往产生的外部交往空间规划设计建议。     

变压吸附技术的应用及其发展简述

文章分析了变压吸附技术存在的问题,并提出解决措施。通过对变压吸附技术应用现状的总结,对该技术未来的发展方向进行预测与评价。指出变压吸附技术能够经济高效地实现物质的分离,有望成为分离技术未来的发展方向,为环保和工业生产做出更大贡献。     

回收与降解聚驱采出水的工艺探讨

含聚污水的处理是困扰石油行业的难题之一。基于聚驱采出水的特点,围绕聚合物的回收利用和降解理论及技术,探讨国内外含聚污水处理技术的研究与应用现状,对比分析现有处理技术存在的问题及适应性,提出采用化学混凝、气浮和水质改性等技术来回收利用PAM(聚丙烯酰胺)的新思路,打破了降解PAM的传统思维,同时分析含聚污水处理与利用技术的可行性与应用前景,有望实现含聚污水的循环利用。