稠油火驱开采技术节能减排效果分析

火驱作为稠油热采的有效接替技术,与注蒸汽开采技术相比,具有采收率高,能耗低,CO_2排放少的优势。文章从火驱驱油机理特征阐述了火驱与注蒸汽技术的不同点,从燃料开采能耗、热效率、注入剂资源、数据对比四个方面分析火驱比注蒸汽热效率高,无燃料开采成本,能耗是注蒸汽的50%;从CO_2气体排放方式和排放量对比可知,火驱能够减少温室气体排放,为油田节能减排、环保生产起到积极作用。     

Hazardous substances in indoor dust emitted from waste TV recycling facility

Various hazardous substances contained in waste TV sets might be released into environment via dust during recycling activities. Two brominated flame retardants (BFRs), polybrominated diphenyl ethers (PBDEs), and tetrabromobisphenol A (TBBPA), and five kinds of heavy metals (Cu, Pb, Cd, Cr, and Ni) were detected in indoor dust collected from two workshops (TV dismantling workshop and subsequent recycling workshop). PBDEs concentrations in dust from waste wires recycling line (722,000 ng/g) were the highest among the studied sites, followed by those in manual dismantling–sorting line (117,000 ng/g), whereas TBBPA concentrations were the highest in manual dismantling–sorting line (557 ng/g) and printed circuit board (PCB) recycling line (428 ng/g). For heavy metals, Cu and Pb were the most enriched metals in all dust samples. The highest concentration of Pb (22,900 mg/kg) was found in TV dismantling workshop-floor dust. Meanwhile, Cu was the predominant metal in dust from the PCB recycling line, especially in dust collected from electrostatic separation area (42,700 mg/kg). Occupational exposure assessment results showed that workers were the most exposed to BDE-209 among the four PBDE congeners (BDE-47, BDE-99, BDE-153, and BDE-209) in both workshops. The hazard quotient (HQ) indicated that noncancerous effects were unlikely for both BFRs and heavy metals (HQ?<?1), and carcinogenic risks for Cd, Cr, and Ni (risk?<?10^?6) on workers in two workshops were relatively low.     

Medium optimization for the production of anti-cyanobacterial substances by Streptomyces sp. HJC-D1 using response surface methodology

Bioremediation using isolated anti-cyanobacterial microorganism has been widely applied in harmful algal blooms (HABs) control. In order to improve the secretion of activated anti-cyanobacterial substances, and lower the cost, a sequential optimization of the culture medium based on statistical design was employed for enhancing the anti-cyanobacterial substances production and chlorophyll a (Chl a) removal by Streptomyces sp. HJC-D1 in the paper. Sucrose and KNO₃ were selected as the most suitable carbon and nitrogen sources based on the one-at-a-time strategy method, and sucrose, KNO₃ and initial pH were found as major factors that affected the anti-cyanobacterial ability of the isolated stain via the Plackett–Burman design. Based on the response surface and canonical analysis, the optimum condition of culture medium was obtained at 22.73 g l^-1 of sucrose, 0.96 g l^-1 of KNO₃, and initial pH 8.82, and the Chl a removal efficiency by strain HJC-D1 increased from 63?±?2 % to 78?±?2 % on the optimum conditions.     

MCM-41介孔分子筛的合成及其对铜离子的吸附性能简

以微硅粉为硅源,CTAB和PEG-6000为模板剂,合成MCM-41介孔分子筛。采用XRD、N₂吸附-脱附曲线、FTIR以及TEM表征了其结构、比表面积、孔径分布及晶体形貌,并且以该样品为吸附剂,对含Cu²⁺的溶液进行了静态吸附实验。结果表明,以微硅粉为硅源成功合成了具有典型六方排列孔道结构的MCM-41,其比表面积为869.5 m²/g,孔容为0.97 cm³/g,平均孔径为3.3 nm;溶液pH为5~6时,MCM-41对Cu²⁺的去除效果最好;MCM-41对Cu²⁺的最大吸附吸附容量36.3 mg/g;MCM-41对Cu²⁺的吸附性能符合Langmuir吸附方程的特征。动力学研究表明,该过程符合准二级动力学模型。     

船舶塑料垃圾热解特性及动力学分析

利用热重分析(TGA)研究船舶塑料垃圾在不同升温速率和不同气氛下的热解特性,并得到了热解动力学参数。结果表明,船舶塑料垃圾的热解过程主要有3个阶段,比一般塑料热解复杂;随着升温速率增大,最大热解速率和最大热解速率温度等热解特性参数也增大,反应变得更剧烈;N2/CO2比为4∶1时,热解反应进行得最完全,固体残留率最少。动力学分析表明,采用3个连续一级反应模型能很好地拟合实验数据;不同的升温速率和气氛比对反应各阶段活化能均有不同程度的影响。     

高铝粉煤灰提取氧化铝后硅钙渣用作水泥混合材

为了使高铝粉煤灰提取氧化铝后所产生的硅钙渣被大量的用作水泥混合材,通过水泥强度、水化放热和干缩性实验研究了原状硅钙渣和脱碱硅钙渣对水泥强度和稳定性的影响。结果表明,当硅钙渣掺量达30%时,硅钙渣水泥强度仍可满足P·C 32.5水泥要求。且随硅钙渣掺入量的增加,水泥早期水化放热速率增加的同时水泥累计水化放热量和干缩率还会显著降低。与原状硅钙渣相比,在同等掺量的情况下,脱碱硅钙渣更有利于保持水泥强度,降低其水化热和改善干缩性。     

温度对正渗透工艺性能的影响

正渗透技术是一种以渗透压差为驱动力的新型膜分离工艺。温度是影响正渗透过程的关键因素。为考察温度在工艺运行中的重要作用,研究了温度对正渗透膜特性及工艺性能的影响,探讨通量衰减机制。结果表明,温度影响汲取液动态稀释、浓差极化和膜污染等的效应程度,进而影响正渗透性能。高温能够明显增加水通量和回收率,且汲取液温度影响比原料液显著。因此,合理优化温度条件是降低能耗提高正渗透性能的有效途径。     

PCBs污染土壤的CaO诱导低温热处理脱氯研究

研究了低温热处理脱氯技术对废弃电容器封存点附近污染土壤中多氯联苯脱氯的效果,考察反应温度、反应时间及CaO添加比例对PCBs去除率、脱氯率的影响以及反应前后土壤中污染物的组分变化。实验土样中PCBs浓度为107.7 mg/g,属于罕见高浓度PCBs污染土壤。当反应温度为400℃、停留时间4h、CaO添加比例为10%,PCBs的去除率为87.7%,脱氯率为85.3%。土壤样品中五氯联苯和四氯联苯反应后含量降低或未检出,部分反应后样品检出一氯联苯和联苯,说明在CaO诱导PCBs低温热处理脱氯反应中存在逐步脱氯/加氢反应途径。     

原铝生产流程温室气体排放主要影响因素的关联度分析

铝是国民经济建设和发展的关键基础材料,然而由其生产过程所产生的大量温室气体排放也逐渐成为政府关注的焦点。本研究计算了我国原铝生产不同年度的生命周期能耗和温室气体排放量,并分析了资源消耗和生产工序能耗等影响因素与温室气体排放的关联性。结果表明,在各年原铝生产的温室气体排放总量中,电力和阳极效应导致的排放所占比重分别为68.5%和7.9%,其他影响因素所占比重均低于6%;与温室气体排放关联度最高的3个影响因素依次是电耗、煤气燃烧和石灰石煅烧,其值分别为0.937、0.899和0.893;在目前铝电耗和阳极效应控制水平提升空间有限的情况下,降低煤气的消耗,提高石灰石的使用效率,是实现原铝生产温室气体减排的有效途径。     

改性丝瓜络纤维对水体日落黄的吸附特性

采用化学改性的方法将丝瓜络制备为阴离子吸附剂,并将其用于水体日落黄(SY)染料的吸附,分别考察了吸附剂的用量、日落黄染料的初始浓度(C0)、p H值、温度(K)、时间(T)5个因素对吸附效果的影响。通过模拟吸附等温曲线、吸附动力学以及热力学方程并通过比表面积(BET)和红外光谱(FTIR)分析改性丝瓜络吸附染料前后和丝瓜络改性前后的变化情况以此探究其吸附机理。结果表明,p H对吸附效果影响不明显;最大吸附量随温度升高而增大,在298 K温度时最大吸附量达到137 mg/g,是未改性丝瓜络的9.78倍。Langmuir方程拟合吸附过程描述最好,吸附类别为化学吸附。吸附过程符合伪二级动力学,是一个自发和吸热的过程。改性丝瓜络可以有效去除水体中的日落黄染料。