Fractionation and potential mobility of trace metals in Danube alluvial aquifer within an industrialized zone

Thirty-five alluvial sediments of the River Danube and 12 groundwater samples were taken within the Pan?evo Oil Refinery (Serbia). The results for groundwater samples exceed European primary drinking water standards for Fe (obtained results, >200 μg/l) and Mn (obtained results, >50 μg/l), while the levels of the trace metals are below the thresholds for drinking water quality. Sediments were treated by sequential extraction procedure with five different solutions, each having a higher extraction capacity than the previous one. We also wanted to determine the possible relationships among trace metals and between sediment properties and elemental concentrations. These solutions partitioned metals into CH₃COONH₄ extractable (F1); HCl carbonate extractable and NH₂OH·HCl easily reducible (F2); (NH₄)₂C₂O₄/H₂C₂O₄ moderately reducible (F3); H₂O₂–HNO₃ organic/sulfide extractable fractions (F4); and HCl acid-soluble residue (F5). The sum of trace metals Ni, Pb, Cu, and Zn associated with the first two fractions (exchangeable, carbonate, and easily reducible) is significant and extremely important because it represents the proportion of heavy metals that can be easily remobilized by changes in environmental conditions such as pH, redox potential, salinity, etc. Sediments located nearer the groundwater flow are exposed to stronger groundwater fluctuation and had a higher quantity of amorphous and less stable substrates of trace metals. Principal component analysis was used to understand and visualize the associations between the trace metals and certain geological forms within analyzed sediments. The observed association between Cr with total sulfur and Mn from the acid-soluble residue could indicate that Cr is in the form of reduced, less toxic Cr(III), which is from the ecochemical point of view very important.     

Management of hazardous medical waste in Croatia

This article provides a review of hazardous medical waste production and its management in Croatia. Even though Croatian regulations define all steps in the waste management chain, implementation of those steps is one of the country's greatest issues. Improper practice is evident from the point of waste production to final disposal. The biggest producers of hazardous medical waste are hospitals that do not implement existing legislation, due to the lack of education and funds. Information on quantities, type and flow of medical waste are inadequate, as is sanitary control. We propose an integrated approach to medical waste management based on a hierarchical structure from the point of generation to its disposal. Priority is given to the reduction of the amounts and potential for harm. Where this is not possible, management includes reduction by sorting and separating, pretreatment on site, safe transportation, final treatment and sanitary disposal. Preferred methods should be the least harmful for human health and the environment. Integrated medical waste management could greatly reduce quantities and consequently financial strains. Landfilling is the predominant route of disposal in Croatia, although the authors believe that incineration is the most appropriate method. In a country such as Croatia, a number of small incinerators would be the most economical solution.     

Distribution of heavy elements in urban and rural surface soils: the Novi Sad city and the surrounding settlements, Serbia

Concentrations of ten heavy elements (Cd, Co, Cr, Cu, Fe, Hg, Mn, Ni, Pb, and Zn), as well as the pH values, organic matter contents, and electrical conductivities were measured in the surface soil samples collected from 21 sites of urban areas in the city of Novi Sad, the second largest city in Serbia, its suburban settlement and the nearby villages. Range of the heavy element concentrations was from 0.16 mg/kg (for Hg) to 18,994 mg/kg (for Fe). Significantly higher Hg and Mn concentrations were observed in subgroups with rural and market garden samples in comparison to the subgroups with urban and grassland samples, respectively, while the contents of Pb found in the grasslands subgroup were significantly higher than in the subgroup with market garden soils. Only one sample of urban soil exceeded the maximum permissible value for Zn set by the relevant Serbian legislation. According to the Dutch soil quality standard, the Cd and Co concentrations in majority of the examined soils were higher than the target values for unpolluted soil. The content of Hg was above the target value in 52% of the samples, most of them belonging to the subgroup of market garden soils. The results for the Novi Sad city area were compared to the relevant data available for other cities in the Western Balkan Countries. Principal component analysis of data revealed seven outlying samples, while the rest of the analyzed samples were grouped together indicating similar heavy element patterns most probably due to mixed emission sources.     

Assessment of GC–MS response of selected pesticides in apple matrices related to matrix concentration

A uniform analyte response is required for GC–MS analysis in order to obtain acceptable quantitative results. The response of pesticides in complex matrices is susceptible to variation due to the interactions of co-extractives, both with pesticides or with GC–MS system. This study was conducted to determine the magnitude of the interactions, called matrix effect, and their behavior with the matrix dilution. The response of pyrimethanil (4,6-dimethyl-N-phenylpyrimidin-2-amine), cyprodinil (4-cyclopropyl-6-methyl-N-phenylpyrimidin-2-amine), trifloxystrobin (methyl-(2Z)-2-methoxyimino-2-[2-[[(E)-1-[3(trifluoromethyl)phenyl]ethylidene amino]oxymethyl]phenyl]acetate) and bifenthrin(2-methyl-3-phenylphenyl)methyl-3-[(Z)-2-chloro-3,3,3-trifluoroprop-1-enyl]-2,2-dimethylcyclopropane-1-carboxylate), used in apple crops protection, was evaluated in different concentrations of peel and flesh extracts of Granny Smith, Golden Delicious and Demi Rouge, selected as representatives of different matrix types. The matrix effect ranged from ?0.05 to 146.14%, depending on matrix type and pesticide. The highest response variation was observed in extracts of Granny Smith—an enhancement in flesh and suppression in peel extract. With the dilution, the matrix effect decreased with different magnitudes, but for Granny Smith peel extract an inverted effect was observed. The presence of the matrix effect in GC–MS pesticides analysis was obvious, requiring the application of matrix-matched calibration in quantification procedures for each variety, with calibration standards matched by the matrix concentration.     

Water-soluble main ions in precipitation over the southeastern Adriatic region: chemical composition and long-range transport

Background, aim and scope  

Precipitation samples collected from 1995 to 2000 at meteorological station in the eastern outskirts of Herceg Novi (Montenegro) were analysed on Na⁺, K⁺, Mg²⁺, Ca²⁺, Cl^–, SO₄ ^2–, NO₃ ^– and NH₄ ⁺. Four-day backward trajectory simulations were conducted during the precipitation period to investigate the regional transport of main ions and their deposition in the region of the southeastern Adriatic Sea. The air mass trajectories were classified into six trajectory categories by the origin and direction of their approach to Herceg Novi.     

Polycyclic aromatic hydrocarbons in air on small spatial and temporal scales – I. Levels and variabilities

Polycyclic aromatic hydrocarbons (PAHs) were measured together with inorganic air pollutants at two urban sites and one rural background site in the Banja Luka area, Bosnia and Hercegovina, during 72 h in July 2008 using a high time resolution (5 samples per day) with the aim to study the spatial and temporal variabilities and to explore the significance of averaging effects inherent to 24 h-sampling. Measurement uncertainty was quantified on basis of three independent side-by-side samplers, deployed at one of the sites.PAH abundances in the urban and rural environments differed largely. Levels at the urban sites exceeded the levels at the rural site by >100%. The discrepancy was largely dominated by emission of 3–4 ring PAHs in the city, while 5–6 ring PAHs were more evenly distributed between city sites and the hill site. During the night a higher fraction of the semivolatile PAHs might have been stored in the soil or sorbed to surfaces. PAH patterns were undistinguishable across the three sites. However, concentrations of more particle-associated substances differed significantly between the urban sites than between one of the urban sites and the rural site (3σ uncertainty). Time-averaging (on a 24 h-basis) would have masked the significant inter-site differences of half of the substances which were found at different levels (on a 4 h-basis).     

The Pollution Load by Nitrogen and Phosphorus IN the Jadro River

The objective of the investigations of the Jadro River, located in Croatia, was to estimate the nitrogen and phosphorus loads in the Jadro River spring and its streamflow by calculating the load in kg/day or tons/year and to compare this with the load for the maximum allowed concentrations (MAC) for drinking water (Official Bulletin, No 46/94) expressed in kg/day or tons/year.Daily pollution loads at the Jadro River spring for total N ranged from 0 to 304 kg, for NH₃-N from 0 to 38 kg, for NO₃-N from 0–1321 kg and for PO₄-P from 0–92 kg in the period from September 1993 to September 2003. When compared with MAC loads the results prove that the Jadro River spring is not polluted by nitrogen compounds and phosphorus.The average annual load for total N ranged from 10 to 33 t, for NH₃-N from 0.25 to 5.15 t, for NO₃-N from 40 to 190 t, and for PO₄-P from 0.3 to 11.5 t. The nitrogen compounds and phosphorus loads vary from one year to another without any constant decreasing or increasing trends. The annual average loads compared with the average annual MAC loads (especially for NH₃-N and PO₄-P) show that there were no threats of constant pollution of the spring.The loads for total N and PO₄-P along the Jadro River flow from the spring to the fishpond entrance were monitored over a five year period from September 1999 to September 2004. The results show no regularities. The highest annual total nitrogen load of 45 t was recorded at the entrance to the fishpond during the 2002/2003 period. The highest annual PO₄-P load of 10 t was measured at the Vidović Bridge during the 2003/2004 period; however, the concentrations of N and P did not exceed the MAC concentrations which are prescribed for drinking water.According to the investigation results of the daily and average annual loads compared with MAC loads for drinking water, it can be concluded that the Jadro River spring and its streamflow are not polluted by nitrogen and phosphorus.     

Utilization of municipal solid waste bottom ash and recycled aggregate in concrete

In the combustion process of municipal solid waste (MSW), bottom ash (BA) represents the major portion of the solid residue. Since BA is composed of oxides, especially SiO(2) and CaO, the feasibility of its application in concrete as a substitute for cement was tested. It was found that at the age of 28 days, the flexural and compressive strengths of the binder linearly decrease at the rate of 0.03 and 0.02 MPa per wt% of BA in the binder, respectively. According to the results it may be recommended to replace up to 15 wt% of cement by BA and to use such binder where a low strength of concrete elements is required. Furthermore, the aggregate used for low strength concrete need not be of a very good quality. Therefore, gravel aggregate was partially replaced by recycled aggregate (RA). Consistency measured by slump was significantly reduced (>50%) when BA or/and RA were introduced into the mixture. However, concrete density and compressive strength were not affected and were approximately 2300 kg/m(3) and approximately 40 MPa, respectively.     

Selective removal of heavy metals from metal-bearing wastewater in a cascade line reactor

Goal, Scope and Background This paper is a part of the research work on ‘Integrated treatment of industrial wastes towards prevention of regional water resources contamination — INTREAT’ the project. It addresses the environmental pollution problems associated with solid and liquid waste/effluents produced by sulfide ore mining and metallurgical activities in the Copper Mining and Smelting Complex Bor (RTB-BOR), Serbia. However, since the minimum solubility for the different metals usually found in the polluted water occurs at different pH values and the hydroxide precipitates are amphoteric in nature, selective removal of mixed metals could be achieved as the multiple stage precipitation. For this reason, acid mine water had to be treated in multiple stages in a continuous precipitation system-cascade line reactor. Materials and Methods All experiments were performed using synthetic metal-bearing effluent with chemical a composition similar to the effluent from open pit, Copper Mining and Smelting Complex Bor (RTB-BOR). That effluent is characterized by low pH (1.78) due to the content of sulfuric acid and heavy metals, such as Cu, Fe, Ni, Mn, Zn with concentrations of 76.680, 26.130, 0.113, 11.490, 1.020 mg/dm³, respectively. The cascade line reactor is equipped with the following components: for feeding of effluents, for injection of the precipitation agent, for pH measurements and control, and for removal of the process gases. The precipitation agent was 1M NaOH. In each of the three reactors, a changing of pH and temperature was observed. In order to verify efficiency of heavy metals removal, chemical analyses of samples taken at different pH was done using AES-ICP. Results Consumption of NaOH in reactors was 370 cm³, 40 cm³ and 80 cm³, respectively. Total time of the experiment was 4 h including feeding of the first reactor. The time necessary to achieve the defined pH value was 25 min for the first reactor and 13 min for both second and third reactors. Taking into account the complete process in the cascade line reactor, the difference between maximum and minimum temperature was as low as 6°C. The quantity of solid residue in reactors respectively was 0.62 g, 2.05 g and 3.91 g. In the case of copper, minimum achieved concentration was 0.62 mg/dm³ at pH = 10.4. At pH = 4.50 content of iron has rapidly decreased to < 0.1 mg/dm³ and maintained constant at all higher pH values. That means that precipitation has already ended at pH=4.5 and maximum efficiency of iron removal was 99.53%. The concentration of manganese was minimum at pH value of 11.0. Minimum obtained concentration of Zn was 2.18 mg/dm³ at a pH value of 11. If pH value is higher than 11, Zn can be re-dissolved. The maximum efficiency of Ni removal reached 76.30% at a pH value of 10.4. Discussion Obtained results show that efficiency of copper, iron and manganese removal is very satisfactory (higher than 90%). The obtained efficiency of Zn and Ni removal is lower (72.30% and 76.31%, respectively). The treated effluent met discharge water standard according to The Council Directive 76/464/EEC on pollution caused by certain dangerous substances into the aquatic environment of the Community. Maximum changing of temperature during the whole process was 6°C. Conclusion This technology, which was based on inducing chemical precipitation of heavy metals is viable for selective removal of heavy metals from metal-bearing effluents in three reactor systems in a cascade line. Recommendations and Perspectives The worldwide increasing concern for the environment and guidelines regarding effluent discharge make their treatment necessary for safe discharge in water receivers. In the case where the effluents contain valuable metals, there is also an additional economic interest to recover these metals and to recycle them as secondary raw materials in different production routes. ESS-Submission Editor: PhD Hailong Wang, hailong.wang@ensisjv.com     

Distribution and fractionation of heavy metals in the Tisa (Tisza) River sediments

Introduction In this work, sediments of the River Tisa (Tisza) are studied to assess their environmental pollution levels for some major heavy metals, as well as to predict the investigated elements’ mobility on the basis of their association type with the substrate. The Tisa River catchments area is a subbasin of the River Danube. Part of this river, 166 km long, belongs to the Serbian province of Vojvodina, before it flows into the Danube. It has been chosen for our investigation, because it has been exposed to intense pollution in the last decades. Materials and Methods The river sediment samples were collected at 32 locations. The proportions of sand, silt and clay fractions were determined. The sequential extraction procedure following a modified Tessier method was applied for speciation of the metal forms in the collected samples. The metal concentrations of Zn, Cd, Pb, Ni, Cu, Cr, Fe and Mn in extracts were determined by atomic absorption spectroscopy. Results and Discussion Granulometric analysis showed that some 50% of the Tisa River sediments were silt and clay, while the rest was sand with quartz, as the main constituent. The average metal content of the surface river sediment samples for every fraction of sequential extraction was presented and discussed in relation to pH, Eh and metal fractionation. The average metal content from the Tisa River sediments, obtained as an average of the metal’s concentration released in all five sequential extraction fractions was compared with: average metal contents of the Tisa River sediments in Hungary, metal content in soils formed on the Tisa River alluvium of Vojvodina, average metal content in soils of Vojvodina, and average metal content in soils of Hungary. An assessment of metal pollution levels in Tisa River sediments was made by comparing mean values for obtained results for the Tisa River sediments with the freshwater sediment’s Quality Guidelines as published by US EPA, Environment Canada and soil standards for Serbia. Conclusion According to US EPA and Canadian Quality Guidelines for freshwater sediments, the concentration of heavy metals in Tisa sediments were: (a) much higher than defined concentrations below which harmful effects on river biota are unlikely to be observed, (b) below defined concentrations above which harmful effects on river biota are likely to be observed. The concentration levels of Pb, Ni, Cu and Cr in Tisa River sediments are safe when compared with Serbian MAQ (Maximum Allowed Quantity) standards for soils, but they are unsafe in the case of Zn and Cd. Recommendations and Outlook The quality of sediments in the Tisa River was on the border line between potentially polluted and polluted. This line could very easily be exceeded since the quality of sediments in the Tisa River in Hungary was already worse than in Serbia. These results indicated the need for further monitoring of heavy metals in that locality.