The reuse of reclaimed water for irrigation around the Mediterranean Rim: a step towards a more virtuous cycle?

Regional Environmental Change - Climate change and a growing population around the Mediterranean Rim are increasing the need for water and, consequently, the pressure on resources in terms of both...     

Municipal solid waste management strategies in Turkey

Municipal solid waste (MSW) is a major environmental problem in Turkey, as in many developing countries. Problems associated with municipal solid waste are difficult to address, but efforts towards more efficient collection and transportation and environmentally acceptable waste disposal continue in Turkey. Although strict regulations on the management of solid waste are in place, primitive disposal methods such as open dumping and discharge into surface water have been used in various parts of Turkey. This study presents a brief history of the legislative trends in Turkey for MSW management. The study also presents the MSW responsibility and management structure together with the present situation of generation, composition, recycling, and treatment. The results show that approximately 25 million ton of MSW are generated annually in Turkey. About 77% of the population receives MSW services. In spite of efforts to change open dumping areas into sanitary landfills and to build modern recycling and composting facilities, Turkey still has over 2000 open dumps.     

Analysis of environmental impact assessment (EIA) system in Turkey

The Environmental Impact Assessment (EIA) System, which embodies the ??prevention principle?? of the environmental law, is an important tool for environmental protection. This tool has a private importance for Turkey since it is a developing country, and it entered the Turkish law in 1983 with the Environmental Law. Besides, the EIA Regulation, which shows the application principles, became effective in 1993. Because Turkey is a candidate for European Union (EU), the EIA Regulation has been changed due to the EU compliance procedure, and its latest version became valid in 2008. This study aims to emphasize The EIA system in Turkey to supervise the efficiency of this procedure and point the success level. In the introduction part, general EIA concept, its importance, and some notations are mentioned. Following that, the legislation, which builds the EIA system, has been analyzed starting from the 1982 Turkish Constitution. Then, the legislation rules are explained due to the basic steps of the EIA procedure. In order to shed light upon the application, the EIA final decisions given until today, the results, and their distributions to the industries are assessed. In the final part of the study, a SWOT analysis is made to mention the weaknesses, strengths, opportunities, and threats of the EIA system in Turkey.     

The use of olive tree (<Emphasis Type="Italic">Olea europaea</Emphasis> L.) leaves as a bioindicator for environmental pollution in the Province of Aydın,Turkey

Introduction  

In this study, olive tree leaves, collected from 50 sampling sites throughout the Province of Aydın, Turkey, were used to estimate level of pollution by measuring Al, As, B, Ba, Ca, Co, Cr, Cu, Fe, K, Li, Mg, Mn, Na, Ni, Pb, Sr, and Zn concentrations and calculating pollution factor (PF) values.     

Assessment of trophic status of the northeastern Mediterranean coastal waters: eutrophication classification tools revisited

Environmental Science and Pollution Research - The Eastern Mediterranean and its Cilician Basin offshore waters have oligotrophic features with low nutrient concentrations, low primary production,...     

Lead removal in fixed-bed columns by zeolite and sepiolite

The removal efficiency of zeolite (clinoptilolite) and sepiolite from lead containing aqueous solutions was investigated. A series of experiments were conducted in batch-wise and fixed-bed columns. Synthetic wastewaters containing lead (50 mg l (-1)) and acetic acid (0.001 N) along with untreated and regenerated clinoptilolites and sepiolites were used in the adsorption studies. Batch tests were mainly conducted to isolate the magnitude of lead precipitation from real adsorption. Adsorption isotherms for both abstraction and adsorption were constructed. The removal of lead is found to be a sum of adsorption induced by ion exchange and precipitation of lead hydroxide. The breakthrough curves were obtained under different conditions by plotting the normalized effluent lead concentration (C/C0) versus bed volume (BV). The ion exchange capacity of sepiolite and clinoptilolite for lead removal showed good performance up to approximately 100 and 120 BV where the C/C0 remained below 0.1, respectively. The lead removal capacity of clinoptilolite bed from wastewater containing only lead yielded 45% higher performance compared to that of acetic acid partly due to a decrease in the effluent pH and consequently in precipitation. Also, the presence of acetic acid in the sepiolite column decreased the bed volumes treated by about 40%. Removal efficiency of lead-acetic system both in untreated clinoptilolite and sepiolite columns was found higher than that in regenerated columns.     

Advanced oxidation treatment of physico-chemically pre-treated olive mill industry effluent

In this study, the applicability of physico-chemical methods was investigated for the pre-treatment of the olive mill effluents prior to the discharge into the common sewerage ending with a municipal wastewater treatment plant. The samples were taken from an olive oil industry operated as three-phase process located in Turkey. Various pre-treatment methods including acid craking, polyelectrolyte and lime additions were applied. Advanced oxidation study using Fenton's process was also investigated following pre-treatment by acid cracking and cationic polyelectrolyte. Acid cracking alone gave satisfactory treatment efficiencies and polyelectrolite additions to the acid-cracked samples enhanced treatment efficiency. Since a complete treatment plant is available at the end of the sewer system, results indicated that the effluents of the investigated industry could be discharged into the municipal sewerage in the case of total chemical oxygen demand (COD(tot)), suspended solid (SS) and volatile suspended solid (VSS) concentrations according to the Turkish Water Pollution Control Regulation after pre-treatment with 5 ppm anionic polyelectrolyte following acid cracking. The minimum COD(tot), SS and VSS removals were observed when raw wastewater was pre-treated with lime and the discharge standards to the municipal sewer system could not be met. Advanced oxidation with Fenton's process was applied after acid cracking and cationic polyelectrolyte treatment in order to investigate further reduction in chemical oxygen demand (COD) concentration for minimizing the influence of this industrial discharge on the existing municipal wastewater treatment plant. Results indicated that COD(tot) removal increased up to 89% from 74% after Fenton's oxidation for the acid cracked samples in which cationic polyelectrolite (10 ppm) was added.     

Production of brown and black pigments by using flotation waste from copper slag.

One of the major problems in copper-producing countries is the treatment of the large amount of copper slag or copper flotation waste generated from copper slag which contains significant amounts of heavy metals such as Cu, Zn, Pb and Co. Dumping or disposal of such large quantities of flotation waste from copper slag causes environmental and space problems. In this study, the treatment of flotation waste from copper slag by a thermal method and its use as an iron source in the production of inorganic brown and black pigments that are used in the ceramic industry were investigated. The pigments were produced by calcining different amounts of flotation waste and chromite, Cr2O3, ZnO and CoO mixtures. The pigments obtained were added to transparent ceramic glazes and porcelainized tile bodies. Their colours were defined by L*a*b* measurements with a spectrophotometer. The results showed that flotation waste from copper slag could be used as an iron source to produce brown and black pigments in both ceramic body and glazes.