Air Pollution in Singapore: Its Multielemental Aspect as Measured by Nuclear Analytical Techniques

Aerosol samples were collected in 1994 in Singapore on two occasions: once in June during the normal meteorological conditions and later in October during a long haze period caused by the heavy forest fire in Indonesia. Filtration and impaction collection methods were used simultaneously so that detailed elemental analysis of bulk as well as of different size fractions could be performed. Accelerator based nuclear analytical techniques such as Particle Induced X-Ray Emission (PIXE), Rutherford Backscattering (RBS) and Nuclear Microscopy (NM) were used for analysis. These techniques are fast, truly multielemental and perfectly suited for routine analysis of a large number of aerosol samples. Typically all samples were analysed for the following 24 elements: Na, Mg, Al, Si, P, S, Cl, K, Ca, Ti, V, Mn, Cr, Fe, Co, Ni, Cu, Zn, Ga, As, Br, Rb, Sr and Pb. Detection limits for bulk analysis were generally below ng/m3 and for single particle analysis absolute detectable mass was approximately 10-17 g. Additionally, trace elements such as Cd, Sn, Sb and Ba whose characteristic X-ray lines were normally "obscured" by the lines of other more abundant elements, were detected when analysing by nuclear microscope in single particle mode.Judging by the average concentrations of lead and sulphur which are good indicators of industrial component of air pollution the situation in Singapore is satisfactory. Pb was typically found in concentrations of 5 to 50 ng/m3 and sulphur in concentrations of 1 to 2 µg/m3. These concentrations are well below limits set by the World Health Organisation (1500 ng/m3 and 40 µg/m3, respectively). On the other hand during the haze period the average concentrations of elements like S, K, Ti, V, Mn, Ni, As and Pb were found to be 3 to 6 times higher than usual. Results are presented and discussed.     

Laboratory and Field Assessment of Arsenic Testing Field Kits in Bangladesh and West Bengal, India

High concentrations of arsenic in ground waters in West Bengal and Bangladeshhave become a major cause for concern in recent years. Given the enormity and the severity of the problemof arsenic poisoning, a task of evaluating the commercially available arsenic detection field kits for their capabilities was undertaken. In the light of the findings, generic specificationswere recommended which could form the basis forindigenous manufacture of these kits in the arsenic affected countries. This article presents the results of the laboratory and fieldevaluation conducted in Bangladesh and West Bengalof five arsenic testing field kits. The salient features of the kits, their merits and limitationshave been brought out. Based on the criteria of kitdesign, quality of chemicals used, colourcomparator charts, detection range, time required for analysis, cost etc., a comparative ranking ofthe kits has been made to facilitate the choice of the kit to meet specific requirements.     

Reduction and avoidance of lubricant mist demands an integrated assessment approach

A case study to identify major factors for lubricant mist exposure covered 15 metal machining sites. The investigation included milling, turning, drilling and grinding applications. Systematic analysis considered all relevant data concerning the machine tool, the lubricant and the suction plant. The efficiency of the implemented maintenance program at the installed filter systems was checked by concentration measurements immediately before and after service. All performed measurements of lubricant aerosol and vapor loads upstream and downstream of the installed filter systems were carried out according to VDI 2066 and BIA 3110, respectively. The selection criteria for the sites to be investigated, the systematic nature of the data acquisition and the procedure of the analysis are demonstrated in detail by performing comparisons between selected applications using emulsions and those employing straight oil for lubrication. The results of the study identify recirculation of ventilated air as the major source of workplace exposure to airborne lubricant emissions. More than 60% of the demisters investigated emit air at total lubricant loads (aerosols and vapor) above the limit of 20 mg m-3 at any time of operation; which also means immediately after service. A common reason for exceeded aerosol loads in recirculated air is e.g. the fact that the type of filter system applied is often not suitable for the separation problem. Loads of lubricant vapor are usually higher at the processes which use water emulsions as lubricant. In a quarter of the cases the limits were exceeded solely due to high vapor loads even immediately after service. The exposure can be reduced by replacing the lubricant, installation of a vapor separation plant or avoiding air recirculation. Maintenance time of the demisting system and aerosol separation efficiency of state-of-the-art demisting systems can be expanded by implementation of enhanced preliminary filter stages. This study confirms that appropriate service measures lower both aerosol emissions and lubricant vapor concentrations due to the reduction of exposed oil-wetted surfaces. The performed measurements show no significant relationship between loads of airborne lubricants and the type of machining process. Therefore, investigations at a much more detailed level have to be performed. However, the individual assessment of any workplace due to the complex situation remains essential.     

Speciation of arsenic using solid phase extraction cartridges

Various solid phase extraction (SPE) cartridges were investigated for speciation of arsenite [As(III)], arsenate [As(v)], monomethylarsonic acid (MMA) and dimethylarsinic acid (DMA). Cartridges containing different types of sorbent materials were tested for arsenic retention and elution characteristics. Alumina cartridges were found to completely retain all the four target arsenic species, and are suitable for removal and preconcentration purposes. For speciation analysis, different arsenic species were separated on the basis of their selective retention on and elution from specific cartridges. DMA was retained on a resin-based strong cation exchange cartridge and eluted with 1.0 M HCl. MMA and As(v) were both retained on a silica-based strong anion exchange cartridge and sequentially eluted with 60 mM acetic acid (for MMA) and 1.0 M HCl [for As(v)]. As(III) was not retained on either cartridge and remained in solution. Arsenic species in solution and those eluted from the cartridges were subsequently quantified by using flow injection with hydride generation atomic fluorescence spectrometry (FI-HGAFS) and hydride generation atomic absorption spectrometry (FI-HGAAS). A detection limit of 0.05 microg L(-1) arsenic in water sample was achieved using HGAFS. An application of the method was demonstrated at a drinking water treatment facility. As(III) and As(v) species were determined in water at various stages of treatment. The method is suitable for routine determination of trace levels of arsenic in drinking water to comply with more stringent environmental regulations.     

Multi-objective, decision-based assessment of a water quality monitoring network in a river system

Water quality monitoring network design has historically tended to use experience, intuition and subjective judgement in locating monitoring stations. Better design procedures to optimize monitoring systems need to simultaneously identify significant planning objectives and consider a number of social, economic and environmental constraints. The consideration of multiple objectives may require further decision analysis to determine the preference weights associated with the objectives to aid in the decision-making process. This may require the application of an optimization study to extract such information from decision makers or experts and to evaluate the overall effectiveness of locating strategies. This paper assesses the optimal expansion and relocation strategies of a water quality monitoring network using a two-stage analysis. The first stage focuses on the information retrieval of preference weights with respect to the designated planning objectives. With the aid of a pre-emptive goal programming model, data analysis is applied to obtain the essential information from the questionnaire outputs. The second stage then utilizes a weighted multi-objective optimization approach to search for the optimal locating strategies of the monitoring stations in the river basin. Practical implementation is illustrated by a case study in the Kao-Ping River Basin, south Taiwan.     

Applying mathematical programming to reserve selection

During the last 10–15 years heuristic methods have been developed for problems in optimal reserve selection. Unfortunately, there is no guarantee that heuristics will find optimal solutions. In recognizing this limitation, analysts have formulated reserve selection problems as set covering problems, for which matrix reduction and integer (0/1) programming can be used to find optimal solutions. In this paper we restate the set covering formulation and review solution techniques. A new 0/1 programming model, which is a generalization of the set covering model, is then presented and applied to a hypothetical reserve selection problem. Objectives of minimizing the number of sites selected and maximizing the number of species represented are addressed. Solutions which characterize the tradeoffs between these objectives provide a rich set of information for planners and decision makers. Applications of mathematical programming to related problems in land use planning and forestry are also discussed.     

Optimal and suboptimal control of anaerobic digesters

Anaerobic digester failure due to entry of inhibitors or sudden changes in the feed substrate concentration may be encompassed beneficially by applying optimal control theory. An almost proportional relationship between the dilution rate and the methane production rate leads to a simple suboptimal control law with only minor loss in performance, after the occurrence of the above mentioned events.     

A simple,cost-effective multispecies toxicity test using organisms with a cosmopolitan distribution

Difficulties in making accurate, ecosystem-level predictions of environmental effects of chemicals, mixtures, and effluents based solely on the results of tests on single species have necessitated the development of more environmentally realistic, predictive testing methods. This paper describes a multispecies, community-level toxicity test based on the colonization of artificial substrates by microbial species. Tests examined the colonization of initially barren polyurethane foam artificial substrates by Protozoa from a species source colonized in a natural system. Differences in colonization were examined in microecosystems amended with low levels of cadmium, a very toxic heavy metal, and TFM, an organic biocide used against larval sea lamprey. Tests examined differences in colonization over 28 days. For cadmium, effect levels were estimated to be near 1 g 1^–1, in the low range of effect levels determined from chronic single species tests. For TFM, effect levels were estimated to be between 1 and 10 ppm, overlapping the concentrations used in environmental applications. The colonization response, which depends on naked microbial cells reproducing and migrating through toxicant amended water to new substrates, is very sensitive. Tests based on colonization can be adapted to use species from a target receiving system or can use species from a designated natural source. Field validation of these tests can employ nearly identical methods to those used in laboratory studies to assess the accuracy of predictions based on test system data.     

Taraxacum species as environmental indicators for grassland management

A classification of the microspecies of the genus Taraxacum was made in a range from low to highly dynamic habitats based on qualitative inventories of grasslands under different management conditions. After several years of constant management, a characteristic species composition occurs. Under mowing (hayfield) conditions, dandelions disappear over a period of about twenty years in a sequence where the low-dynamic species T. adamii and T. nordstedtii are the last to vanish. Different microspecies in the section Vulgaria in one field can show small differences in response to environmental conditions, even where no other directly visible indication exists. New appearance of highly dynamic species can indicate disturbance of some kind or other within a relatively short period. The classification adopted seems to be correlated with the phosphate content of the soil. Differences in two easily perceptible morphological characteristics, namely position of the outer bracts and colour of the leaf-stem, fit into the established sequence. Small changes in these characteristics indicate conditions in the field that are improving or worsening from a nature-conservation point of view. A system is introduced in which merely these two morphological characters, without further taxonomical knowledge, can be used for an evaluation of grasslands and the impact of management practice.     

Pesticide burden on some insects of economic importance in Lucknow (India)

Some insects of economic importance from Lucknow (India) have been investigated for their pesticide burden. Chlorinated pesticide residues of DDT, BHC and aldrin along with their metabolites and isomers have been detected in crop pollinating insects, honeybees (Apis indica) and butterflies (Danais chrysippus and Eurema sp.) and predators, dragonfly (Platythemis sp.) and wasps (Polistes herebreus). DDT and their metabolites were present in concentrations which varied from 231–796 ng g^–1, followed by BHC (10–60 ng g^–1), and aldrin (0.26–6.68 ng g^–1). This finding is likely to stimulate newer interest in the area of pesticide research and start meaningful investigation to find if bioaccumulated pesticides would have adverse impact on otherwise beneficial potentials of such insects in our ecosystems.