Daytime resolved analysis of polycyclic aromatic hydrocarbons in urban aerosol samples - impact of sources and meteorological conditions

Urban aerosol was collected in a summer and a winter campaign for 7 and 3 days, respectively. Low volume samples were taken with a time resolution of 160 min using a filter/sorption cartridge system extended by an ozone scrubber. Concentrations of mainly particle associated polycyclic aromatic hydrocarbons (PAH) and oxidised PAH (O-PAH) were determined by gas chromatography/high resolution mass spectrometry. The sampling site was located in the city centre of Augsburg, Germany, near major roads with high traffic volume. The daily concentrations and profiles were mainly governed by local emissions from traffic and domestic heating, as well as by the meteorological conditions. During the winter campaign, concentrations were more than 10 fold higher than during the summer campaign. Highest concentrations were found concurrent with low boundary layer heights and low wind speeds. Significant diurnal variation of the PAH profiles was observed. Enhanced influences of traffic related PAH on the PAH profiles were evident during daytime in summer, whereas emissions from hot water generation and domestic heating were obvious during the night time of both seasons. A general idea about the global meteorological situation was acquired using back trajectory calculations (NOAA ARL HYSPLIT4). Due to high local emissions in combination with low air exchange during the two sampling campaigns, effects of mesoscale transport were not clearly observable.     

Electrochemical degradation applied to the metabolites of Acid Orange 7 anaerobic biotreatment

The electrochemical oxidation of the biotic degradation products of the textile dye C.I. Acid Orange 7 (AO7) was achieved using a boron doped diamond electrode (BDD). Tests were performed with model solutions of the biotic degradation products, sulphanilic acid (SA) and 1-amino-2-naphthol (AN), and also with real effluents obtained in experiments carried out in an up-flow anaerobic sludge blanket (UASB) reactor, fed with a simulated textile effluent containing AO7, working in mesophilic or thermophilic conditions. Bulk electrolysis was studied using two different supporting electrolytes - NaCl and Na(2)SO(4). The influence of initial metabolite concentration and current density on the electrodegradation rates of the biotic products was investigated. For the UASB effluents, oxidation tests were carried out for different electrolytes and at different current densities. Samples were collected at pre-selected intervals and absorbance measurements, chemical oxygen demand (COD) and total organic carbon (TOC) tests and high performance liquid chromatography (HPLC) analysis were performed. Results have shown an almost complete elimination of the persistent pollutants and a COD removal higher than 70% for both AN and SA. For the UASB effluents, COD removals between 45% and 90% and TOC removals varying from 19% to 41% were obtained.     

Transport of Sr2+ and SrEDTA2- in partially-saturated and heterogeneous sediments

Strontium-90 has migrated deep into the unsaturated subsurface beneath leaking storage tanks in the Waste Management Areas (WMA) at the U.S. Department of Energy's (DOE) Hanford Reservation. Faster than expected transport of contaminants in the vadose zone is typically attributed to either physical hydrologic processes such as development of preferential flow pathways, or to geochemical processes such as the formation of stable, anionic complexes with organic chelates, e.g., ethylenediaminetetraacetic acid (EDTA). The goal of this paper is to determine whether hydrological processes in the Hanford sediments can influence the geochemistry of the system and hence control transport of Sr(2+) and SrEDTA(2-). The study used batch isotherms, saturated packed column experiments, and an unsaturated transport experiment in an undisturbed core. Isotherms and repacked column experiments suggested that the SrEDTA(2-) complex was unstable in the presence of Hanford sediments, resulting in dissociation and transport of Sr(2+) as a divalent cation. A decrease in sorption with increasing solid:solution ratio for Sr(2+) and SrEDTA(2-) suggested mineral dissolution resulted in competition for sorption sites and the formation of stable aqueous complexes. This was confirmed by detection of MgEDTA(2-), MnEDTA(2-), PbEDTA(2-), and unidentified Sr and Ca complexes. Displacement of Sr(2+) through a partially-saturated undisturbed core resulted in less retardation and more irreversible sorption than was observed in the saturated repacked columns, and model results suggested a significant reservoir (49%) of immobile water was present during transport through the heterogeneous layered sediments. The undisturbed core was subsequently disassembled along distinct bedding planes and subjected to sequential extractions. Strontium was unequally distributed between carbonates (49%), ion exchange sites (37%), and the oxide (14%) fraction. An inverse relationship between mass wetness and Sr suggested that sandy sediments of low water content constituted the immobile flow regime. Our results suggested that the sequestration of Sr(2+) in partially-saturated, heterogeneous sediments was most likely due to the formation of immobile water in drier regions having low hydraulic conductivities.     

A synchronized amphibian metamorphosis assay as an improved tool to detect thyroid hormone disturbance by endocrine disruptors and apolar sediment extracts

Amphibian metamorphosis assays are used to evaluate potential effects of endocrine disrupting compounds on the thyroid hormone axis. In this study, Xenopus laevis tadpoles are kept in a solution of 0.2% thiourea (TU) to arrest and synchronise them in their development. The advantage of this synchronized amphibian metamorphosis assays is that synchronised tadpoles are available at any time to start metamorphosis experiments, and experimental groups are much more homogenous at the start of experimental exposure compared with groups selected from an untreated pool of animals. The water volume per animal was kept constant throughout the experimental period to overcome the influence of declining numbers of animals per aquarium due to metamorphosis and mortality on the density dependent development of the remaining tadpoles. Clophen A50 (a technical PCB mixture), the single congener 3,3',4,4'-tetrachlorobiphenyl (PCB 77) and apolar sediment extracts that were previously tested positive in the T-Screen, an in vitro proliferation assay for thyroid hormone disruption, were tested in the Synchronized Amphibian Metamorphosis Assay. Endpoints studied were mortality, malformations, body weight, and percentage of metamorphosed froglets at the end of the 60-day experimental period, percentage of tadpoles in different developmental stages, and developmental stage-dependent awarded penalty points. Dietary exposure to Clophen A50 (0.2-50mg/kg food) resulted in a significant increased percentage of tadpoles that did not pass metamorphosis at concentrations higher than 2mg/kg food. Time until metamorphosis in those animals that were able to metamorphose after the 60-days experimental period was significantly decreased. Dietary exposure to PCB 77, a congener that can be readily metabolised, did not result in significant effects in any exposure group (2-500 microg/kg food). Apolar sediment extracts from two of the three sites that are contaminated with a wide variety of chemicals significantly decreased the percentage of metamorphosed animals and significantly increased the number of tadpoles that remained in early and late metamorphic stages. These effects already occurred when the extracts where diluted more than 1000 times (on an organic carbon base) compared to environmental concentrations. The rank of potency was comparable to results obtained with the T-screen. This suggests the presence of thyroid hormone disrupting compounds in the aquatic environment and possible effects of such compounds on animal development in the wild.     

Risk assessment of linear alkylbenzene sulphonates, LAS, in agricultural soil revisited: robust chronic toxicity tests for Folsomia candida (Collembola), Aporrectodea caliginosa (Oligochaeta) and Enchytraeus crypticus (Enchytraeidae)

To obtain robust data on the toxicity of LAS, tests with the collembolan Folsomia candida L., the oligochaetes Aporrectodea caliginosa Savigny (earthworm) and Enchytraeus crypticus Westheide and Graefe (enchytraeid) were performed in a sandy loam soil. Additionally limited tests with LAS spiked to sewage sludge, and subsequently mixed into soil, were performed. For the endpoint of interest, reproduction in soil, we found an EC10 of 205 mg LAS kg(-1) soil [8.6-401] [95% confidence limits] for F. candida and an EC10 of 46 mg LAS kg(-1) soil [13-80] for A. caliginosa after 28 days. E. crypticus was not affected by concentrations up to 120 mg LAS kg(-1) soil. When adding (low contaminated) non-spiked sludge to soil, high stimulation of reproduction was observed for E. crypticus and A. caliginosa but not for F. candida. We argue that this difference in stimulative response between the tested species is related to the difference in feeding behaviour. Sludge spiked with LAS did not significantly affect the reproduction of F. candida (fertility: number of juvenile offspring) and A. caliginosa (fecundity: number of cocoons) (dose equivalent to 181 g and 91 g LAS kg(-1) sludge, respectively). Significantly reduced reproduction was observed for E. crypticus (at 120 mg LAS kg(-1) soil+sludge corresponding to 72 g LAS kg(-1) sludge) compared to non-spiked sludge. The reproduction by E. crypticus was, however, comparable to the reproduction observed in the control soil without sludge. Compared to LAS directly spiked to soil, the reproductive output of organisms exposed to spiked sludge was either not significantly different (F. candida, E. crypticus) or significantly improved (A. caliginosa). More studies are needed in order to make firm conclusions on the potential effect of artificially contaminated sludge in soil systems.     

Filamentous scum bacteria in activated sludge plants: detection and identification quality by conventional activated sludge microscopy versus fluorescence in situ hybridization.

Detection of filamentous bacteria morphotypes involved in scum formation in activated sludge wastewater treatment plants by conventional sludge microscopy is often doomed to fail because of morphological and taxonomical variations. The aim of this study is to compare detection, identification, and quantification quality of filamentous "scum bacteria" found by conventional activated sludge microscopy and fluorescence in situ hybridization (FISH). In the case of filamentous Microthrix parvicella and Eikelboom morphotypes 1863 and 1851, conventional activated sludge microscopy and FISH results correspond well. In contrast, conventional activated sludge microscopy overlooks nocardioform actinomycete and type 1863 single cells. On the other hand, FISH underestimates filamentous nocardioform actinomycetes and morphotypes 0041/0675 or 0092 because of insufficient cell wall permeability or because of their taxonomic variability, with a resulting inadequacy of previously published probes. Nostocoida limicola morphotype results are still inconclusive because of low bacteria numbers being available in situ and the enormous taxonomic variability within this group.     

Real-time measurement of outdoor tobacco smoke particles

The current lack of empirical data on outdoor tobacco smoke (OTS) levels impedes OTS exposure and risk assessments. We sought to measure peak and time-averaged OTS concentrations in common outdoor settings near smokers and to explore the determinants of time-varying OTS levels, including the effects of source proximity and wind. Using five types of real-time airborne particle monitoring devices, we obtained more than 8000 min worth of continuous monitoring data, during which there were measurable OTS levels. Measurement intervals ranged from 2 sec to 1 min for the different instruments. We monitored OTS levels during 15 on-site visits to 10 outdoor public places where active cigar and cigarette smokers were present, including parks, sidewalk cafés, and restaurant and pub patios. For three of the visits and during 4 additional days of monitoring outdoors and indoors at a private residence, we controlled smoking activity at precise distances from monitored positions. The overall average OTS respirable particle concentration for the surveys of public places during smoking was approximately 30 microg m(-3). OTS exhibited sharp spikes in particle mass concentration during smoking that sometimes exceeded 1000 microg m(-3) at distances within 0.5 m of the source. Some average concentrations over the duration of a cigarette and within 0.5 m exceeded 200 microg m(-3), with some average downwind levels exceeding 500 microg m(-3). OTS levels in a constant upwind direction from an active cigarette source were nearly zero. OTS levels also approached zero at distances greater than approximately 2 m from a single cigarette. During periods of active smoking, peak and average OTS levels near smokers rivaled indoor tobacco smoke concentrations. However, OTS levels dropped almost instantly after smoking activity ceased. Based on our results, it is possible for OTS to present a nuisance or hazard under certain conditions of wind and smoker proximity.     

Refinery evaluation of optical imaging to locate fugitive emissions

Fugitive emissions account for approximately 50% of total hydrocarbon emissions from process plants. Federal and state regulations aiming at controlling these emissions require refineries and petrochemical plants in the United States to implement a Leak Detection and Repair Program (LDAR). The current regulatory work practice, U.S. Environment Protection Agency Method 21, requires designated components to be monitored individually at regular intervals. The annual costs of these LDAR programs in a typical refinery can exceed US$1,000,000. Previous studies have shown that a majority of controllable fugitive emissions come from a very small fraction of components. The Smart LDAR program aims to find cost-effective methods to monitor and reduce emissions from these large leakers. Optical gas imaging has been identified as one such technology that can help achieve this objective. This paper discusses a refinery evaluation of an instrument based on backscatter absorption gas imaging technology. This portable camera allows an operator to scan components more quickly and image gas leaks in real time. During the evaluation, the instrument was able to identify leaking components that were the source of 97% of the total mass emissions from leaks detected. More than 27,000 components were monitored. This was achieved in far less time than it would have taken using Method 21. In addition, the instrument was able to find leaks from components that are not required to be monitored by the current LDAR regulations. The technology principles and the parameters that affect instrument performance are also discussed in the paper.     

Desorption of PCDD/PCDF from municipal solid waste incinerator flyash under post-combustion plant conditions

The influence of temperature on the levels of PCDD and PCDF remaining in, and desorbed from, a municipal solid waste incinerator flyash was investigated by heating the ash to between 200 and 400 degrees C under a simulated flue gas for four days reaction time. Considerable desorption of PCDD/PCDF from the flyash was seen at 275 degrees C and above. Maximum desorption occurred at 350 degrees C, with the equivalent of nearly eight times the total PCDD/PCDF concentration of the original flyash being lost to the vapour phase per unit mass of initial flyash. The I-TEQ value of the desorbed PCDD/PCDF was considerable, being over fourteen times that of the original flyash at 325 degrees C. The results indicate that formation of PCDD/PCDF on flyash deposits in the post-combustion plant of incinerators can result in the release of significant amounts of PCDD/PCDF to the flue gas stream.     

Development and verification of a toxicokinetic model of polychlorinated biphenyl elimination in persons working in a contaminated building

BACKGROUND: Polychlorinated biphenyls are toxic and slowly degrading substances that have been in widespread industrial use in the 1960s and 1970s. Despite a worldwide reduction, environmental exposure remains an issue; the assessment of an individual's level of exposure at a given time in retrospect requires valid toxicokinetic modeling of the different PCB congeners. OBJECTIVES: To develop and verify a toxicokinetic model of the in vivo-degradation of PCB 28 and 52 in adult humans. METHODS: The plasma concentrations of PCB congeners were measured in 583 persons working in a contaminated building for an average of 14.7+/-9.6 years. The values were adapted to a simple pharmacokinetic model (yt = y0 x (1 - e(-kt))); the steady state concentration y0 was estimated based on the median values of persons working exposed more than 10 years. RESULTS: The steady state concentration of PCB 28 was 0.10 microg/l, that of PCB 52 0.02 microg/l. The half-life of the congeners was estimated based on a logarithmic regression analysis according to the model mentioned above; it was 2.18 (95% CI: 1.91-2.54) years for PCB 28 and 3.95 (95% CI: 3.55-4.45) years for PCB 52, respectively. Stepwise elimination of persons with very long employment duration did not reduce the estimated half-life. CONCLUSIONS: The estimated half-life is higher than previously published data especially for PCB 52. Possible reasons and implications of this finding are discussed.