基于不同废污泥源的短程反硝化快速启动及稳定性

为探究不同废污泥源快速启动短程反硝化和实现稳定NO_2~--N积累的可行性,在3个完全相同的SBR反应器(S1、S2和S3)分别接种:实验室城市污水反硝化除磷系统排泥、城市污水厂剩余污泥及河涌底泥,比较其短程反硝化启动快慢和NO_2~--N积累特性,考察系统短程反硝化活性和NO_3~--N→NO_2~--N转化性能,并从微生物学角度分析反应器功能菌群特征.结果表明,在乙酸钠为唯一碳源、高碱度和适宜COD/NO_3~--N比进水条件下,3个SBR短程反硝化反应器在短时间内均能够成功启动,系统平均NO_3~--N→NO_2~--N转化率为S1 S2 S3(75. 92% 73. 36% 69. 90%).同时发现持续低温条件下S1和S2呈现不同程度的短程反硝化性能恶化趋势,但S3能够稳定维持良好NO_2~--N积累性能.微生物高通量测序表明,变形菌门和拟杆菌门居PD系统主导地位,3个短程反硝化反应器NO_2~--N积累关键功能菌属Thauera属丰度差异明显:S3 S1 S2(25. 09% 4. 71% 3. 60%),表明S3具备稳定高效的NO_2~--N积累性能,同时高丰度Thauera属可能是维持低温短程反硝化活性的重要原因.     

哈尔滨市秸秆焚烧大气污染负荷估算方法研究

本文针对近些年哈尔滨秋末冬初大气污染程度增加的溯源问题,基于静风污染气象及降雪对秸秆焚烧的影响等基本假设,采用箱式模型和优化拟合的方法对秸秆焚烧产生污染物的源强及其负荷进行了估算.通过对2015年和2017年典型时段数据的优化拟合得到降雪前重污染天气下PM₁₀排放源强分别为20.16、21.83 μg·m^-2·s^-1,CO的排放源强分别为149.32、138.65 mg·m^-2·s^-1;降雪后重污染天气下PM₁₀排放源强分别为15.98、7.09 μg·m^-2·s^-1,CO的排放源强分别为122.91、89.21 mg·m^-2·s^-1.由降雪前后各污染物的源强差得到2015年和2017年秸秆焚烧产生的PM₁₀的排放源强分别为4.18、14.74 μg·m^-2·s^-1,负荷分别为20.73%、67.52%;CO的排放源强分别为26.41、49.44 mg·m^-2·s^-1,负荷分别为17.69%、35.66%.本文为相关清单的研究提供了一种客观的校核方法,具有重要的社会、环境及现实意义.     

不同空间划分方式下袁河流域景观结构对水质的影响

近年来景观结构的水文效应受到关注,研究不同空间划分方式下景观结构对河流营养盐、重金属变化的影响机制对于流域生态保护具有重要意义.本文于2018年7月和2019年1月在袁河干流及支流38个采样点采集水样,测定水体营养盐类污染指标（DO、NO₃^--N、NH₄⁺-N、TP和DOC浓度）和重金属类污染指标（Cr、Mn、Fe、Cu、Zn、As、Cd和Pb浓度）.基于前向变量选择、冗余分析等方法,筛选景观结构指标,量化其在不同尺度下对水体营养盐、重金属变化的影响.结果表明：①农田、斑块密度（PD）、斑块聚集指数（COHESION）及散布与并列指数（IJI）是影响水体营养盐变化的主要指标.林地、建设用地（Res）、平均最近邻体距离（ENN_MN）和最大斑块指数（LPI）的组合是影响重金属变化的主要指标.②在河岸缓冲带与圆形缓冲区划分方式下,景观结构均在100 m尺度对营养盐变化解释能力最强,平均解释率分别为31.5%、24.3%,均在1000 m尺度对重金属变化解释能力最强,平均解释率分别为32.0%、42.6%.③100 m河岸缓冲带和子流域尺度分别是景观结构影响水体营养盐、重金属变化的最佳空间尺度,平均解释率分别为31.5%、42.8%.以上结果表明,针对水体不同的污染类型,采用对应的划分方式及缓冲尺度有助于提高定量分析精度,为流域水环境保护、景观优化与管理提供科学依据.     

全球液化石油气运输网络贸易社区特征及其演化分析

液化石油气在全球清洁能源消耗市场中扮演着极为重要的角色,其通过船舶在不同港口之间进行运输,而港口之间通过局部密集的运输关系,形成了联系极为紧密的贸易社区。采用复杂网络社区探测方法,基于2013—2017年全球液化石油气船舶轨迹大数据构建运输网络,并对其贸易社区特征及其演化趋势开展分析。结果表明：（1）液化石油气（Liquefied Petroleum Gas,LPG）贸易社区内的港口之间的联系更加紧密,不同社区内的枢纽港口联系也日益紧密;（2）各个贸易社区的规模呈现出增长趋势,且同一社区内的港口在地理空间上变得更为集聚;（3）亚太地区、中东、西北欧和地中海地区形成的社区在全球LPG贸易中一直保持着重要地位,而随着时间推移,美洲社区已逐渐从一个相对孤立的社区发展成为与其他社区存在紧密联系的社区。     

漓江流域δD和δ18O对蒸发的指示作用

以漓江流域为例查明不同水体之间氢氧稳定同位素组成特征,并探讨氢氧稳定同位素对漓江流域的蒸发过程指示作用.结果表明：流域内不同水体之间,氢氧稳定同位素表现出不同的组成特征,地表水和地下水,在丰水期δD值和δ¹⁸O值要比枯水期更容易富集,地下水的δD值和δ¹⁸O值分布范围较地表水小;随着水温的升高,δ¹⁸O的变化趋势比d-excess明显.从漓江上游到下游高程逐渐下降,河水线的斜率和截距也在逐渐减小,其中漓江下游河水线的斜率和截距要低于当地大气降水线,表明下游受到蒸发作用较强烈;地下河水线、地表河水线在一定程度上偏离当地大气降水线,但偏离程度较小,表明三者之间有很好的水力联系.受温度和湿度的共同影响,漓江干流丰水期河水的蒸发量占最初水体总量的0.7%~9.1%,枯水期河水的蒸发量占最初水体总量的2.6%~9.7%,丰水期的蒸发比例低于枯水期,从上游到下游蒸发比例在逐渐上升.研究区蒸发量估算值为959.40mm,与多年实测值少43.11mm,相对误差4.70%.氢氧稳定同位素对研究区降水、地表水、地下水之间的转换规律具有重要的实际意义,在今后的漓江流域水文研究中有着更加广阔的空间.     

北方湖库沉积物重金属区域特征及生态风险评价

以白洋淀、衡水湖、于桥水库、松花湖、大伙房水库和小兴凯湖沉积作为研究对象,通过对北方六湖库沉积物中Cu、Zn、Pb、Cr、Ni等重金属元素进行分析,并与国内外其他水域重金属污染情况进行多因素比较,探讨了六湖库主要重金属污染源的差异性,区域分布特征以及与国内外其他水域污染的相似性和区别.结果表明,六湖库沉积物重金属污染处于中等偏下水平.六湖库之间主要重金属污染源存在差别.沉积物重金属含量未出现明显上升的趋势.其中Zn、Pb存在富集现象,但Pb含量与历史数据相比出现下降,Zn的含量与其他地区相比整体偏高.大伙房水库沉积物重金属污染较重,Cu、Zn、Pb、Cr、Ni含量平均值分别为56.28,142.3,17.44,97.9,44.44mg/kg.小兴凯湖沉积物重金属含量最低,Cu、Zn、Pb、Cr、Ni含量平均值分别为2.41,63.90,13.37,56.36,26.09mg/kg.六湖库综合风险评价结果为大伙房水库>于桥水库>白洋淀>衡水湖>松花湖>小兴凯湖,重金属整体潜在生态风险指数为低.     

Preparation of hydrophobic hierarchical pore carbon–silica composite and its adsorption performance toward volatile organic compounds

Carbon–silica materials with hierarchical pores consisting of micropores and mesopores were prepared by introducing nanocarbon microspheres derived from biomass sugar into silica gel channels in a hydrothermal environment.The physicochemical properties of the materials were characterized by nitrogen physical adsorption(BET),scanning electron microscopy(SEM),and thermogravimetric(TG),and the adsorption properties of various organic waste gases were investigated.The results showed that microporous carbon materials were introduced successfully into the silica gel channels,thus showing the high adsorption capacity of activated carbon in high humidity organic waste gas,and the high stability and mechanical strength of the silica gel.The dynamic adsorption behavior confirmed that the carbon–silica material had excellent adsorption capacity for different volatile organic compounds(VOCs).Furthermore,the carbon–silica material exhibited excellent desorption characteristics:adsorbed toluene was completely desorbed at 150℃,thereby showing superior regeneration characteristics.Both features were attributed to the formation of hierarchical pores.     

Acceleration of floc-water separation and floc reduction with magnetic nanoparticles during demulsification of complex waste cutting emulsions

Waste cutting emulsions are difficult to treat efficiently owing to their complex composition and stable emulsified structure. As an important treatment method for emulsions, chemical demulsification is faced with challenges such as low flocs–water separation rates and high sludge production. Hence, in this study, Fe₃O₄ magnetic nanoparticles (MNPs) were used to enhance chemical demulsification performance for treating waste cutting emulsions under a magnetic field. The addition of MNPs significantly decreased the time required to attain sludge–water separation and sludge compression equilibrium, from 210 to 20 min. In addition, the volume percentage of sludge produced at the equilibrium state was reduced from 45% to 10%. This excellent flocculation–separation performance was stable over a pH range of 3–11. The magnetization of the flocculants and oil droplets to form a flocculant–MNP–oil droplet composite, and the magnetic transfer of the composite were two key processes that enhanced the separation of cutting emulsions. Specifically, the interactions among MNPs, flocculants, and oil droplets were important in the magnetization process, which was controlled by the structures and properties of the three components. Under the magnetic field, the magnetized flocculant–MNP–oil droplet composites were considerably accelerated and separated from water, and the sludge was simultaneously compressed. Thus, this study expands the applicability of magnetic separation techniques in the treatment of complex waste cutting emulsions.     

干湿法结合工艺回收废弃SCR脱硝催化剂中的钛、钒和钨

利用干湿法结合工艺实现废弃SCR脱硝催化剂中Ti、V和W元素的高效分离和浸出,提出成套废弃SCR脱硝催化剂中Ti、V和W的回收技术。以废弃SCR脱硝催化剂为研究对象,优选Ti、V和W元素最佳浸出工况,研究硫酸溶解法回收TiO₂和有机萃取法回收V₂O₅和WO₃的回收率与纯度。结果表明:酸浸还原浸钒最优工艺条件为温度140℃,液固比30∶1;钠化焙烧浸钨最优工艺条件为煅烧温度750℃,反应物与Na₂CO₃配比（质量比）为1∶1.5,在以上条件下V、W浸出率分别达到97.6%、93.6%。利用硫酸溶解法回收得到的TiO₂产物主要以锐钛矿晶型存在形式,在最佳焙烧温度750℃下,TiO₂回收率达到97.17%,纯度为95.35%。利用有机萃取法回收得到的V₂O₅和WO₃产物的回收率和纯度分别为72.47%、75.43%和93.25%、78.26%。     

Development of a static test apparatus for evaluating the performance of three PM2.5 separators commonly used in China

PM_(2.5) separator directly affects the accuracy of PM_(2.5) sampling.The specification testing and evaluation for PM_(2.5) separator is particularly important,especially under China's wide variation of terrain and climate.In this study,first a static test apparatus based on polydisperse aerosol was established and calibrated to evaluate the performance of the PM_(2.5) separators.A uniform mixing chamber was developed to make particles mix completely.The aerosol concentration relative standard deviations of three test points at the same horizontal chamber position were less than 0.57%,and the particle size distribution obeyed logarithmic normal distribution with an R~2 of 0.996.The flow rate deviation between the measurement and the set point flow rate agreed to within ± 1.0% in the range of -40 to 50℃.Secondly,the separation,flow and loading characteristics of three cyclone separators(VSCC-A,SCC-A and SCC112) were evaluated using this system.The results showed that the 50% cutoff sizes(D_(50)) of the three cyclones were 2.48,2.47 and 2.44 μm when worked at the manufacturer's recommended flow rates,respectively.The geometric standard deviation(GSD) of the capture efficiency of VSCCA was 1.23,showed a slightly sharper than SCC-A(GSD = 1.27),while the SCC112 did not meet the relevant indicator(GSD = 1.2 ± 0.1) with a GSD = 1.44.The flow rate and loading test had a great effect on D_(50),while the GSD remained almost the same as before.In addition,the maintenance frequency under different air pollution conditions of the cyclones was summarized according to the loading test.