Material cycles in Asia: especially the recycling loop between Japan and China

In this article, we clarify the current status of Japanese exports and Chinese imports of secondary resources. A total of around 10 million metric tons (t) of secondary resources are exported annually from Japan to China, Hong Kong, and Korea. Hong Kong plays the role of a transshipment point, especially regarding the trade in plastic waste, and China imports much from the USA and Japan, often through Hong Kong. The secondary resources exported from Japan include both byproducts from manufacturing processes and end-of-life products or materials. The great demand in China, and the difference in prices between countries, drive this transboundary shipment, although Japan has enacted various recycling laws that were implicitly intended to promote domestic recycling. In China, the imported secondary resources are recycled, usually by means of primitive and low-cost hand labor. The greatest concern is whether there are still improper (illegal or polluting) recycling activities in China. International material cycles should prevent environmental pollution and ensure efficient resource utilization. To that end, the following measures are needed: cooperative control of the trade of secondary resources between countries, the alignment of domestic laws with the regulations in other countries based on the actual trade activities, and the realization of sound practices for global resources management.     

Development of a database of landfills and dump sites in Asian countries

This article briefly summarizes the limited landfill/dump information available for developing Asian countries, and introduces a database that aims to close the information gap through collecting and sharing data. Developing nations usually try to adapt the systems and technologies of developed countries. However, this approach may not be appropriate because of differences in socioeconomic, cultural, and political backgrounds. Many waste management projects fail after operations are transferred to local authorities owing to a lack of funds to cover the high operational expenses. Some successful projects have been adapted to local conditions, although the information on these successes is not often available for others. Nevertheless, only a few developing countries even have a national inventory of their dumps/landfills, and decision-makers have little awareness of the dumps and their impacts. The database introduced here will gather landfill/dump information from each country and organize it in a comparable format, and it will then be published on the Internet.     

Utilization of red mud as catalyst in conversion of waste oil and waste plastics to fuel

The aim of this study was to investigate the possibilities of using a by-product (red mud) from alumina production as a catalyst for recovery of waste. The conversion of waste mineral oil (WMO) and waste mineral oil/municipal waste plastic (WMO/MWP) blends over red mud (RM), a commercial hydrocracking catalyst (silica–alumina), and a commercial hydrotreating catalyst (Ni–Mo/alumina) to fuel has been studied. The effect of the catalyst and the temperature on the product distribution (gas, liquid, and wax) and the properties of liquid products were investigated. In the case of hydrotreatment of WMO, the liquids obtained over RM at both 400° and 425°C had larger amounts of low-boiling hydrocarbons than that of thermal or catalytic treatment with hydrotreating catalyst. Gas chromatography and nuclear magnetic resonance analysis of the liquid products showed that RM had hydrogenation and cracking activity in hydrotreatment of WMO. In coprocessing of WMO with municipal waste plastics, temperature had an important effect as well as the amount of MWP in the blend and the catalyst type. The hydrocracking at 400°C produced no liquid product. In hydrocracking at 425°C, the product distribution varied with catalyst type and MWP amount. The commercial hydrocracking catalyst had more cracking ability in the conversion of WMO/MWP to liquid and gas fuel than RM. In the case of hydrocracking over RM, the largest amount of liquid having satisfactory quality was obtained only from the blend containing 20% MWP.     

Headspace-SPME-GC-MS Identification of Volatile Organic Compounds Released from Expanded Polystyrene

A method for the identification of volatile organic compounds (VOCs) released from packaging expanded polystyrene (EPS) is presented. Headspace solid-phase microextraction (HS-SPME) with a 75-m carboxen-polydimethylsiloxan fiber was used as sample preparation technique before the determination of the volatile organic compounds by gas chromatography–mass spectrometry (GC-MS). For separation of compounds, two fused silica capillary columns of different polarity (DB-5ms and BPX-50) were used. Styrene monomer with his impurities and oxidation products, as well as residual pentane, were identified in the headspace of EPS.     

Ring-Opening Polymerization of Cyclic Esters onto Liquefied Biomass

Ring-opening polymerization of cyclic esters (-caprolactone, -valerolactone, and l-lactide) onto liquefied biomass (LB) was conducted to obtain the polyester-type polyol and to regulate the characteristics of LB. IR and ¹H-NMR spectra of the obtained polyol showed that the polymerization was successfully conducted in the presence of acid catalyst, which is used in liquefaction. The molecular weight (M_w), hydroxyl value, and viscosity were controllable by changing the reaction conditions. Polyester-type polyurethane foams with a wide range of properties were prepared from the obtained polyol with the appropriate combinations of foaming agents.     

Reusability of sewage sludge in clay bricks

Bricks produced from sewage sludge in different compositions were investigated. Results of the tests indicated that the sludge proportion is a key factor in determining the brick quality. Increasing the sludge content results in a decrease in brick shrinkage, bulk density, and compressive strength. Brick weight loss on ignition was mainly due to the contribution of the contained organic matter from the sludge being burnt off during the firing process, as well as inorganic substances found in both clay and sludge. The physical, mechanical, and chemical properties of the bricks that were supplemented with various proportions of dried sludge from 10 to 40wt% and generally complied with the General Specification for Brick as per the Malaysian Standard MS 7.6:1972, which dictates the requirements for clay bricks used in walling in general. A standard leaching test method also showed that the leaching of metals from the bricks is very low.     

Recovery of gold by chicken egg shell membrane-conjugated chitosan beads

We have successfully prepared a bead-type adsorbent from two materials with different adsorption characteristics. Heavy metals were removed by greatly swollen egg shell membrane-conjugated chitosan beads. The egg shell membrane accumulated and removed precious metal ions from a dilute aqueous solution with a high affinity in a short contact time. Experiments suggested that chitosan beads could take up gold ions with great capacity and selectivity by conjugation with egg shell membrane. Under certain conditions, the selective removal of gold and copper in a mixture of gold and copper ions by egg shell membrane-conjugated chitosan beads was 100% and 2%, respectively. Egg shell membrane-conjugated chitosan beads can be seen as a promising material to recover gold in wastewater from various industries, such as electroplating.     

Influences of Magnesium <Emphasis Type="Italic">tri-</Emphasis>Silicate on the Physical,Mechanical, and Degradable Properties of Ultraviolet (UV) Radiation Cured Plain Board Surface

A series of formulations were prepared with different percentages of oligomer, epoxy diacrylate (EA-1020 ), monomer, 1,6 Hexane diol diacrylate,(HDDA) and different percentages of filler (Magnesium tri-silicate, Mg₂Si₃O₈). Irgacure 369 [2-Benzyl-2-dimethyl-amine-1 (4-morpholinophenyl) butanone-1] was used in the formulations as photoinitiator. Ultraviolet (UV) cured thin polymer films were prepared from these formulating solutions on clean glass plates. Pendulum hardness (PH), gel content and macro scratch hardness (MSH) of the UV cured films were studied. One percent Mg₂Si₃O₈ containing formulation showed the premium properties. The substrates (plain board) were coated by these formulating solutions and cured under the same UV lamp at different intensities of radiation. Various properties of the coated surface such as PH, gloss, adhesion, abrasion and MSH were investigated. The base coat containing 1% Mg₂Si₃O₈ and top coat containing 48% HDDA produced the best performance among all the formulations inspected. The degradable properties in different weathering conditions on PH, gloss, adhesion, abrasion and MSH were measured. The surface cured with the optimized formulation (E) again yielded the minimum loss of the properties.     

Pore structure and adsorption properties of activated carbon prepared from granular molded waste paper

We have previously manufactured activated carbon using waste paper board, which was prepared by adding 8% phenol resin adhesive to torn waste newspaper and hot-pressing. In this study, the pretreatment process of the raw material was simplified; the waste paper was extruded to form granules. The activated carbon was manufactured by the carbon dioxide activation method using the granules as the raw material. The properties of the activated carbon were evaluated based on the pore structure, the iodine adsorption number, and the adsorption of toluene vapor in a sealed chamber. The activated carbon, which was manufactured at an activation temperature of 1100°C and a treatment time of 60min, exhibited a specific surface area of 1241m²/g and an iodine adsorption number of 1120mg/g. These results were similar to those obtained for two commercially available activated carbons. The extent of toluene vapor adsorption by this activated carbon was similar to that observed for the two commercial activated carbons over a period of 130min.     

Phosphorus loss and runoff characteristics in three adjacent agricultural watersheds with claypan soils

Effects of precipitation, runoff, and management on total phosphorus (TP) loss from three adjacent, row-cropped watersheds in the claypan region of northeastern Missouri were examined from 1991 to 1997 to understand factors affecting P loss in watersheds dominated by claypan soils. Runoff samples from each individual runoff event were analyzed for TP and sediment concentration. The annual TP loss ranged from 0.29 to 3.59 kg ha(-1) with a mean of 1.36 kg ha(-1) across all the watersheds during the study period. Significantly higher loss of TP from the watersheds was observed during the fallow period. Multiple small runoff events or several large runoff events contributed to loss of TP from the watersheds. Total P loss in 1993, a year with above-normal precipitation, accounted for 30% of the total TP loss observed over seven years. The five largest runoff events out of a total of 66 events observed over seven years accounted for 27% of the TP loss. The five largest sediment losses were responsible for 24% of the TP loss over seven years. Runoff volume and sediment loss explained 64 to 73% and 47 to 58% of the variation in TP loss on watersheds during the study. Flow duration and maximum flow accounted for 49 and 66% of TP loss, respectively. The results of this study suggest that management practices that reduce runoff volume, flow duration, maximum flow, and sediment loss, and that maintain a suitable vegetative cover throughout the year could lower P loss in claypan soils.