钙钛矿型催化剂催化湿式氧化处理煤气化废水纳滤浓缩液

采用溶胶-凝胶法制备了Mn掺杂钙钛矿型催化剂LaFexMn1-xO3,并以其为催化剂催化湿式双氧水氧化处理煤气化废水纳滤浓缩液。采用XRD,SEM,FTIR技术对催化剂进行了表征。表征结果显示：制备的催化剂均具有标准的钙钛矿型结构,其中,LaFe0.9Mn0.1O3的结构稳定,比表面积大。实验结果表明：制备的催化剂中LaFe0.9Mn0.1O3的催化活性最高,且稳定性好,连续使用5次后催化活性未见明显减弱;在H2O2投加量3.0 g/L、n（H2O2）∶n（LaFe0.9Mn0.1O3）=12∶1、反应温度160 ℃、反应压力1 MPa、浓缩液pH 3、反应时间60 min的最优条件下,COD、UV254和TOC的去除率分别达到80.9%、95.2%和68.0%,BOD5/COD由0.02提升至0.40,可生化性大幅提高。     

Absorption characteristics of potassium carbonate-based solutions with rate promoters and corrosion inhibitors

In this research, absorbents for CO₂ capture were prepared by blending 30 wt% potassium carbonate, 3 wt% of a rate promoter, and 1 wt% of a corrosion inhibitor. Pipecolic acid, sarcosine, and diethanolamine were chosen as rate promoter candidates. Based on a rate promoter screening test for CO₂ loading capacity and absorption rate, pipecolic acid and sarcosine were selected to be used as rate promoters. 1,2,3-benzotriazole and ammonium thiocyanate were chosen as corrosion inhibitors, and they were mixed with a 30 wt% potassium carbonate-based absorbent mixture containing one of the rate promoters. The absorption rates for four absorbent solutions (30 wt% potassium carbonate?+?3 wt% pipecolic acid?+?1 wt% 1,2,3-benzotriazole, 30 wt% potassium carbonate?+?3 wt% pipecolic acid?+?1 wt% ammonium thiocyanate, 30 wt% potassium carbonate?+?3 wt% sarcosine?+?1 wt% 1,2,3-benzotriazole, and 30 wt% potassium carbonate?+?3 wt% sarcosine?+?1 wt% ammonium thiocyanate) were measured, tabulated, and graphically displayed. These types of absorbents can be used for capturing CO₂ under high temperature and pressure conditions, such as those found in coal-fired power plants.     

以硝酸盐为主要氮源的反硝化除磷细菌驯化

以活性污泥为种泥,通过序批式反应器(Sequencing Batch Reactor,SBR),在厌氧-缺氧-好氧交替的条件下驯化培养以硝酸盐为主要氮源的反硝化除磷细菌(Denitrifying Phosphorus-Accumulating Organisms,DPAO)。在330 d的培养时间内监测磷酸盐、硝酸盐和亚硝酸盐等常规指标,并研究驯化不同阶段的一个周期内各指标的变化及进行相应的动力学分析。结果表明,随着驯化的进行,厌氧阶段释磷速率逐渐增加,释磷量也相应增大,出水磷质量浓度最终维持在0.8mg/L,去除率达到91.8%,硝氮全部去除。通过对16S r RNA测序结果的比对,得到聚磷菌占总菌的76.93%,反硝化除磷菌占聚磷菌的一半以上。而聚糖菌仅占5.13%,聚磷菌成为优势菌种。此外,在整个驯化过程中,水质和环境条件的变化使出水中磷质量浓度出现波动,而出水硝氮的变化不大。研究表明,以硝酸盐作为主要氮源培养反硝化除磷细菌的方式是可行的,并有利于聚磷菌对聚糖菌的竞争,使聚磷菌成为优势菌种。     

基于Ap/Vp的双薄壁高墩刚构桥抗震性能研究

为了研究地震频谱特性对柔性桥梁抗震性能的影响,以正弦波为例推导了地震动能量与A_p/V_p的关系,基于能力需求比提出了桥梁抗震性能评估方法及计算公式。以某典型高墩连续刚构桥为工程背景,采用地震动参数A_p=0.4g的22条正弦波和7条实际地震记录,对比研究了桥梁纵、横向抗震性能随A_p/V_p的变化规律。结果表明:在地震动参数A_p相同的情况下,桥梁关键截面抗震能力需求比在纵、横桥向均随A_p/V_p的增大而呈现增长的规律,最大增幅超过12.92倍(正弦波)和2.31倍(实际波);按正弦波得到能力需求比普遍大于实际波,且随A_p/V_p增大而增大的规律更明显。研究发现将地震动参数A_p作为单一的抗震设计指标会导致桥梁抗震性能离散性很大,A_p/V_p可作为柔性桥梁抗震设计的补充指标。     

Investigation of titanium liquid/gas diffusion layers in proton exchange membrane electrolyzer cells

In a proton exchange membrane electrolyzer cell (PEMEC), liquid/gas diffusion layer (LGDL) is expected to transport electrons, heat, and reactants/products to and from the catalyst layer with minimum voltage, current, thermal, interfacial, and fluidic losses. In addition, carbon materials, which are typically used in PEM fuel cells (PEMFCs), are unsuitable in PEMECs due to the high ohmic potential and highly oxidative environment of the oxygen electrode. In this study, a set of titanium gas diffusion layers with different thicknesses and porosities are designed and examined coupled with the development of a robust titanium bipolar plate. It has been found that the performance of electrolyzer improves along with a decrease in thickness or porosity of the anode LGDL of titanium woven meshes. The ohmic resistance of anode LGDL and contact resistance between anode LGDL and the anode catalyst play dominant roles in electrolyzer performance, and better performance can be obtained by reducing ohmic resistance. Thin titanium LGDLs with straight-through pores and optimal pore morphologies are recommended for the future developments of low-cost LGDLs with minimum ohmic/transport losses.     

煤粉炉掺烧干化污泥的污染物排放研究

结合某电厂420 t/h四角煤粉炉掺烧污泥项目的实验室分析测试,了解煤粉掺烧不同含水率不同比例的干化污泥条件下烟气中污染物和灰渣中重金属的排放特性。结果表明,在实验研究配比和燃烧的条件下,大部分重金属元素Pb、Cu、Cr和Ni残留在灰渣中,Zn、Cd部分残留在灰渣中,As、Hg和Se等易挥发元素释放到烟气中,在灰渣中的含量很小。掺烧污泥后,灰渣中的重金属含量较单烧单煤都有了一定幅度的升高,Zn的含量是单煤的2倍,其余重金属是单煤的1.1~1.2倍。3种不同的掺混比例之间的污染气体排放浓度基本相似。烟气中主要污染物及重金属浓度可以满足现行国家标准。与单烧单煤相比,CO、HCl以及其他有机气体排放浓度基本相同;NH3的排放浓度较单煤有所升高;SO2、NOx和CO2排放浓度略有降低;飞灰浓度有所升高。烟气中的重金属,Hg含量升高了30%,Pb含量约为单煤的4.3~4.8倍。以上研究结果可为环保达标和飞灰利用提供基础数据。     

Estimating and comparing greenhouse gas emissions with their uncertainties using different methods: A case study for an energy supply utility

Energy supply utilities release significant amounts of greenhouse gases (GHGs) into the atmosphere. It is essential to accurately estimate GHG emissions with their uncertainties, for reducing GHG emissions and mitigating climate change. GHG emissions can be calculated by an activity-based method (i.e., fuel consumption) and continuous emission measurement (CEM). In this study, GHG emissions such as CO₂, CH₄, and N₂O are estimated for a heat generation utility, which uses bituminous coal as fuel, by applying both the activity-based method and CEM. CO₂ emissions by the activity-based method are 12–19% less than that by the CEM, while N₂O and CH₄ emissions by the activity-based method are two orders of magnitude and 60% less than those by the CEM, respectively. Comparing GHG emissions (as CO₂ equivalent) from both methods, total GHG emissions by the activity-based methods are 12–27% lower than that by the CEM, as CO₂ and N₂O emissions are lower than those by the CEM. Results from uncertainty estimation show that uncertainties in the GHG emissions by the activity-based methods range from 3.4% to about 20%, from 67% to 900%, and from about 70% to about 200% for CO₂, N₂O, and CH₄, respectively, while uncertainties in the GHG emissions by the CEM range from 4% to 4.5%. For the activity-based methods, an uncertainty in the Intergovernmental Panel on Climate Change (IPCC) default net calorific value (NCV) is the major uncertainty contributor to CO₂ emissions, while an uncertainty in the IPCC default emission factor is the major uncertainty contributor to CH₄ and N₂O emissions. For the CEM, an uncertainty in volumetric flow measurement, especially for the distribution of the volumetric flow rate in a stack, is the major uncertainty contributor to all GHG emissions, while uncertainties in concentration measurements contribute a little to uncertainties in the GHG emissions.

Implications:Energy supply utilities contribute a significant portion of the global greenhouse gas (GHG) emissions. It is important to accurately estimate GHG emissions with their uncertainties for reducing GHG emissions and mitigating climate change. GHG emissions can be estimated by an activity-based method and by continuous emission measurement (CEM), yet little study has been done to calculate GHG emissions with uncertainty analysis. This study estimates GHG emissions and their uncertainties, and also identifies major uncertainty contributors for each method.     

添加炭基材料对蔬菜废物好氧堆肥进程和腐熟度的影响

以蔬菜废弃物辣椒秸秆和树叶为堆肥原料(CK),采用密闭式好氧堆肥工艺,研究了添加5%木本泥炭(T1)、5%活性炭(T2)和10%木本泥炭(T3)等炭基材料对堆肥p H、EC、CO2累积量、物料损失率、T值、C/N和发芽率指数的影响。结果显示,T2处理的p H在60 d后维持在8~9之间;EC值随着堆肥进行呈现先下降后升高再下降的趋势,最终CK、T1、T2和T3处理的EC值(m S/cm)分别降低了1.02、0.76、0.33和0.48;T2和T3处理的CO2累积量一直高于其他处理;所有处理的物料损失率均在20%以上;4个处理堆肥产品的T值分别为0.56、0.65、0.68和0.69;堆肥产品的发芽率指数分别为63.2%、69.3%、93.5%和86.1%。T值和发芽率指数显示T2和T3处理达到了腐熟阶段。结果表明,在蔬菜堆肥处理中添加炭基材料可改善堆肥产品的理化性质,加速堆肥物料的分解,有效地缩短堆肥周期和提高堆肥产品的腐熟度。     

A real-time monitoring and assessment method for calculation of total amounts of indoor air pollutants emitted in subway stations

Subway systems are considered as main public transportation facility in developed countries. Time spent by people in indoors, such as underground spaces, subway stations, and indoor buildings, has gradually increased in the recent past. Especially, operators or old persons who stay in indoor environments more than 15 hr per day usually influenced a greater extent by indoor air pollutants. Hence, regulations on indoor air pollutants are needed to ensure good health of people. Therefore, in this study, a new cumulative calculation method for the estimation of total amounts of indoor air pollutants emitted inside the subway station is proposed by taking cumulative amounts of indoor air pollutants based on integration concept. Minimum concentration of individual air pollutants which naturally exist in indoor space is referred as base concentration of air pollutants and can be found from the data collected. After subtracting the value of base concentration from data point of each data set of indoor air pollutant, the primary quantity of emitted air pollutant is calculated. After integration is carried out with these values, adding the base concentration to the integration quantity gives the total amount of indoor air pollutant emitted. Moreover, the values of new index for cumulative indoor air quality obtained for 1 day are calculated using the values of cumulative air quality index (CAI). Cumulative comprehensive indoor air quality index (CCIAI) is also proposed to compare the values of cumulative concentrations of indoor air pollutants. From the results, it is clear that the cumulative assessment approach of indoor air quality (IAQ) is useful for monitoring the values of total amounts of indoor air pollutants emitted, in case of exposure to indoor air pollutants for a long time. Also, the values of CCIAI are influenced more by the values of concentration of NO₂, which is released due to the use of air conditioners and combustion of the fuel. The results obtained in this study confirm that the proposed method can be applied to monitor total amounts of indoor air pollutants emitted, inside apartments and hospitals as well.

Implications: Nowadays, subway systems are considered as main public transportation facility in developed countries. Time spent by people in indoors, such as underground spaces, subway stations, and indoor buildings, has gradually increased in the recent past. Especially, operators or old persons who stay in the indoor environments more than 15 hr per day usually influenced a greater extent by indoor air pollutants. Hence, regulations on indoor air pollutants are needed to ensure good health of people. Therefore, this paper presents a new methodology for monitoring and assessing total amounts of indoor air pollutants emitted inside underground spaces and subway stations. A new methodology for the calculation of cumulative amounts of indoor air pollutants based on integration concept is proposed. The results suggest that the cumulative assessment approach of IAQ is useful for monitoring the values of total amounts of indoor air pollutants, if indoor air pollutants accumulated for a long time, especially NO₂ pollutants. The results obtained here confirm that the proposed method can be applied to monitor total amounts of indoor air pollutants emitted, inside apartments and hospitals as well.     

江苏省地理标志概况与价值评估体系构建研究

以江苏省43个地理标志为研究对象,根据国家地理标志的分类方法对其进行分类,构建价值评估体系,探讨地理标志产品的内在价值及发展重点。研究表明,江苏省地理标志类型较为单一,分布均匀;开发程度不同,可分为开发匮乏型、有待开发型和开发成熟型。通过价值体系评价可见,江苏省应重点挖掘产品的自身特色,发展价值意义突出的地理标志。