污泥生物炭制备吸附陶粒

以城市污泥热解产生的生物炭(BC)与高岭土(KL)为原料制备吸附陶粒(SKC),研究其对环丙沙星(CIP)的吸脱附性能,开展吸附动力学和等温吸附特性研究,结合形貌、孔结构、物相组成、表面电位探讨其吸附机制,利用TCLP法研究重金属浸出特征.结果表明BC与KL以6∶4的质量比混合造粒,经1 050℃烧结5 min得到的SKC对CIP有明显的吸附效果,去除率达65.34%;SKC对CIP的吸附符合二级动力学模型,在不同质量浓度下的吸附特性适用于Freundlich等温吸附模型,吸附过程同时存在物理和化学吸附.SKC具有良好的孔隙结构,物相组成以硅铝氧化物、铁氧化物和金属磷酸盐为主,既能降低重金属的浸出毒性又具有良好的CIP吸附去除效果,有望为处理废水中高浓度CIP提供一种低成本可回收的吸附材料,也为BC的规模化安全利用提供了新思路.     

磷酸根和镉离子在羟基铁改性膨润土表面的协同吸附机制研究

聚合羟基金属-粘土矿物复合物广泛存在于自然环境中,对重金属阳离子和含氧酸根阴离子均有很好的吸附能力,因此对这些化合物的环境迁移过程及污染控制具有重要影响.研究采用FeCl₃和Na₂CO₃共同改性膨润土,制备了羟基铁－膨润土复合物（HyFe-Bent）.XRD和孔结构分析结果发现,HyFe-Bent的d₀₀₁由原土的1.52 nm增加到1.81 nm,比表面积由原土的52.2 m²·g^-1增大到108.4 m²·g^-1.将HyFe-Bent用于同时吸附水中磷酸根（P）和镉离子（Cd）,结果表明,在实验条件下P和Cd在HyFe-Bent上表现出明显的协同吸附效应,溶液pH升高可促进Cd的吸附但降低P的吸附.此外研究了P和Cd吸附次序对它们吸附性能的影响：在先吸附P的体系中两种物质的吸附性能与同时吸附体系相当,而在先吸附Cd的体系中吸附性能则明显低于同时吸附体系.由此提出P和Cd协同吸附的原理是多种吸附机制共存：除了配体交换和离子交换作用,它们在HyFe-Bent表面还发生了表面沉淀作用,可能形成了Fe-P-Cd三元络合产物.论文研究结果可为了解重金属和含氧酸根复合体系的环境行为及污染控制提供新信息.     

复合生物絮凝剂CBF-1的絮凝作用机理研究

采取PAC+絮凝剂的复配方式开展高岭土悬浊液烧杯实验,考察了复合生物絮凝剂CBF-1、CBF-1溶解物及微生物絮凝剂MBF8的絮凝特性,并借助iPDA仪分析和扫描电镜、光学显微镜观察等手段,比较分析了絮凝过程及絮体特性的差异.结果表明,各复配絮凝的浊度去除效果排序为CBF-1＞ CBF-1溶解物＞MBF8,CBF-1投加量1 mg·L-1时,浊度去除率可达到97.5％;絮体强度排序为CBF-1＞ CBF-1溶解物＞MBF8,絮体恢复因子排序为MBF8＞CBF-1溶解物＞CBF-1,絮体大小排序为CBF-1＞ CBF-1溶解物＞MBF8.单独投加PAC或投加PAC+MBF8的情况下,形成的絮体形态相对规整、密实;投加PAC+ CBF-1溶解物或投加PAC+ CBF-1形成的絮体则相对无序、疏松,CBF-1作用下絮体大、沉降快.CBF-1中高电荷MBF8组分及大分子羧甲基纤维素、羧甲基多聚糖等组分具有强的电荷中和与桥联协同增效作用;CBF-1还含有纤维素、木质素等大分子量且带多种官能团的不溶性组分,在桥联和吸附过程中也起着重要作用.     

改性壳聚糖CAD与微生物絮凝剂MBF8复配絮凝研究

采用水溶液自由基聚合反应,将丙烯酰胺(AM)、二甲基二烯丙基氯化铵(DMDAAC)接枝到壳聚糖分子上制成了阳离子改性壳聚糖(CAD).经FT-IR、XRD、zeta(ξ)电位、凝胶色谱等分析确定,CAD为淡黄色透明液体,pH值为3.7,相对分子质量为2.88×10⁶,阳离子度为16.7,等电点(0.1%溶液)约为pH值10.5,有效成分2.6%,主要特征官能团有羟基、氨基、季铵基和酰胺基, 呈不规则晶体结构.将CAD与相对分子质量3.67×10⁵的多糖类电负性微生物絮凝剂MBF8复配,对浊度12~460 NTU、离子强度3.0 mmol·L^-1的高岭土悬浊液进行烧杯实验.结果表明,MBF8与CAD的最佳使用方式为先投加MBF8后投加CAD,复配比5:3时效果最好,适用的pH范围为6.0~10.0.采用PAC(3.0 mg·L^-1)+MBF8+CAD(1.0 mg·L^-1)复配絮凝,pH=8.0下,对浊度为110 NTU的高岭土悬浊液,浊度去除率>97%,残余铝<0.08 mg·L^-1,絮体大、沉降快,絮凝效果优于PAC+分子量800万、1200万的阴离子PAM及分子量1500万的阳离子PAM.     

乙醇处理对树脂基纳米水合氧化铁结构及其除砷性能的影响

通过考察乙醇处理对树脂基纳米水合氧化铁(D201-HFO)结构及其除砷性能的影响,评价乙醇处理在复合材料制备中的必要性.结果表明,乙醇处理后负载水合氧化铁(HFO)在D201树脂内的分散性增加,材料对砷的饱和吸附量提高约20%,且复合材料的比表面积、孔容、孔径分别增加了52%、65%、28%;但乙醇处理对复合材料的机械强度和负载HFO的晶型无影响,在pH值、离子竞争对该材料除砷性能的影响趋势方面也无明显作用,对复合材料固定床除砷性能及再生方面也无明显作用.总体而言,乙醇处理对D201-HFO复合材料实际除砷性能影响不大,从技术经济性考虑可以省略.     

Sulfur-containing amino acid methionine as the precursor of volatile organic sulfur compounds in algea-induced black bloom

After the application of methionine, a progressive and significant increase occurred in five volatile organic sulfur compounds (VOSCs): methanethiol (MeSH), dimethyl sulfide (DMS), dimethyl disulfide (DMDS), dimethyl trisulfide (DMTS) and dimethyl tetrasulfide (DMTeS). Even in the untreated control without a methionine addition, methionine and its catabolites (VOSCs, mainly DMDS) were found in considerable amounts that were high enough to account for the water’s offensive odor. However, blackening only occurred in two methionine-amended treatments. The VOSCs production was observed to precede black color development, and the reaching of a peak value for total VOSCs was often followed by water blackening. The presence of glucose stimulated the degradation of methionine while postponing the occurrence of the black color and inhibiting the production of VOSCs. In addition, DMDS was found to be the most abundant species produced after the addition of methionine alone, and DMTeS appeared to be the most important compound produced after the addition of methionine+glucose. These results suggest that methionine acted as an important precursor of the VOSCs in lakes suffering from algea-induced black bloom. The existence of glucose may change the transformation pathway of methionine into VOSCs to form larger molecular weight compounds, such as DMTS and DMTeS.     

Cost-performance analysis of nutrient removal in a full-scale oxidation ditch process based on kinetic modeling

A full-scale oxidation ditch process for treating sewage was simulated with the ASM2d model and optimized for minimal cost with acceptable performance in terms of ammonium and phosphorus removal. A unified index was introduced by integrating operational costs (aeration energy and sludge production) with effluent violations for performance evaluation. Scenario analysis showed that,in comparison with the baseline (all of the 9 aerators activated), the strategy of activating 5 aerators could save aeration energy significantly with an ammonium violation below 10%. Sludge discharge scenario analysis showed that a sludge discharge flow of 250–300 m3/day (solid retention time (SRT), 13–15 days) was appropriate for the enhancement of phosphorus removal without excessive sludge production. The proposed optimal control strategy was: activating 5 rotating disks operated with a mode of "111100100" ( "1"represents activation and "0" represents inactivation) for aeration and sludge discharge flow of 200 m3/day (SRT, 19 days). Compared with the baseline, this strategy could achieve ammonium violation below 10% and TP violation below 30% with substantial reduction of aeration energy cost (46%) and minimal increment of sludge production (< 2%). This study provides a useful approach for the optimization of process operation and control.     

Pb(II) removal from water using Fe-coated bamboo charcoal with the assistance of microwaves

Bamboo charcoal(BC) was used as starting material to prepare iron-modified bamboo charcoal(Fe-MBC) by its impregnation in FeCl 3 and HNO 3 solutions simultaneously,followed by microwave heating.The material can be used as an adsorbent for Pb(Ⅱ) contaminants removal in water.The composites were prepared with Fe molar concentration of 0.5,1.0 and 2.0 mol/L and characterized by means of N 2 adsorption-desorption isotherms,X-ray diffraction spectroscopy(XRD),scanning electron microscopy coupled with energy dispersive X-ray spectrometry(SEM-EDS),Fourier transform infrared(FT-IR) and point of zero charge(pH pzc) measurements.Nitrogen adsorption analyses showed that the BET specific surface area and total pore volume increased with iron impregnation.The adsorbent with Fe molar concentration of 2 mol/L(2Fe-MBC) exhibited the highest surface area and produced the best pore structure.The Pb(Ⅱ) adsorption process of 2Fe-MBC and BC were evaluated in batch experiments and 2Fe-MBC showed an excellent adsorption capability for removal Pb(Ⅱ).The adsorption of Pb(Ⅱ) strongly depended on solution pH,with maximum values at pH 5.0.The ionic strength had a significant effect on the adsorption at pH < 6.0.The adsorption isotherms followed the Langmuir isotherm model well,and the maximum adsorption capacity for Pb(Ⅱ) was 200.38 mg/g for 2Fe-MBC.The adsorption processes were well fitted by a pseudo second-order kinetic model.Thermodynamic parameters showed that the adsorption of Pb(Ⅱ) onto Fe-MBC was feasible,spontaneous,and exothermic under the studied conditions,and the ion exchange mechanism played an significant role.These results have important implications for the design of low-cost and effective adsorbents in the removal of Pb(Ⅱ) from wastewater.     

石化行业催化裂化装置环境监理要点研究——以某企业350万吨/年催化裂化装置为例

催化裂化是石油炼厂从重质油生产汽油的主要过程之一,是石化炼油中的核心部分,也是环境监理关注的重点.以某石化公司油品质量升级改造项目为例,对新建350万吨/年催化裂化装置的环境监理开展深入研究,为国内深入开展类似项目的环境监理工作、出台环境监理技术规范提供有益的参考.     

化工业清洁生产技术措施分析

化工业是导致环境污染的主要产业.当前,我国的化工产业所采用的生产方式仍然是传统的粗放式生产,给我国的生态环境带来了很大的压力.在这种情况下,除了转变生产方式之外,最有效的方法就是采用清洁生产技术.文章通过在化工业生产中使用清洁原料、使用清洁化学反应、使用清洁反应介质、使用清洁水处理技术等多个方面,对化工业清洁生产技术进行了系统性的分析,为广大化工业研究、生产人员提供了参考.