裂解温度和离子强度对不同来源生物炭胶体释放行为的影响

近年来环境中生物炭胶体形成受到广泛关注,它是生物炭在环境中物理分解作用的重要过程,对污染物迁移有着重要影响.然而,目前对生物炭胶体释放过程和影响因素的研究甚少,人们对生物炭胶体释放机理的认识还很有限.本研究以小麦秸秆和花生壳为生物质来源,系统地探讨了生物炭的裂解温度（300~700 ℃）和溶液离子强度（0.1~10 mmol·L^-1）对生物炭胶体产率的影响.结果表明,随着裂解温度的升高,生物炭的耐磨性增强,且在较高的裂解温度下（≥500 ℃）花生壳生物炭的耐磨性显著强于小麦秸秆生物炭.生物炭的胶体产率受到生物质来源和裂解温度的显著影响,花生壳生物炭的胶体产率低于小麦秸秆生物炭,高温裂解（≥600 ℃）生物炭的胶体产率显著低于中低温裂解生物炭.在相同溶液离子强度下,生物炭胶体产率与其亚微米级碎片率呈显著正相关（p<0.05）,即生物炭中亚微米级碎片率越高,生物炭胶体产率越高.当溶液离子强度从1 mmol·L^-1增加到10 mmol·L^-1时,两种来源生物炭的胶体产率均显著降低,其降低的程度因生物炭裂解温度而异,其中低温裂解（300 ℃）生物炭的胶体产率降低了11.1%~11.2%,中高温裂解（≥ 500 ℃）生物炭的胶体产率降低了60.0%~97.2%.     

内质网应激在氟暴露致小鼠睾丸损伤中的作用

探讨了内质网应激在亚慢性氟暴露致小鼠睾丸损伤中的作用及分子机制.选用健康初断乳ICR雄性小鼠30只,随机分为对照组（C）、低氟组（LF）和高氟组（HF）,分别饮用自来水、5、30 mg·L^-1氟化钠水溶液90 d.亚慢性氟暴露结束后,以睾丸脏器系数、睾丸组织氧化/抗氧化酶和形态结构、精子质量、睾丸细胞凋亡、葡萄糖调节蛋白78（GRP78）、CCAAT/增强子结合蛋白同源蛋白（CHOP）、半胱氨酸天冬氨酸蛋白酶12（CASPASE-12）、半胱氨酸天冬氨酸蛋白酶3（CASPASE-3）为观测点.结果表明,与对照组比,LF组和HF组LDH、SOD、T-AOC活性下降,MDA含量上升,HF组GSH-PX活性下降,差异有统计学意义（p<0.05或p<0.01）;LF组可见细胞层次减少、间隙变大,成熟精子数量减少,HF组细胞溶解、层次紊乱,空泡化严重,少见成熟精子;LF组和HF组小鼠的精子活力降低,HF组小鼠精子数量下降,畸形率上升,差异有统计学意义（p<0.05或p<0.01）;LF组和HF组睾丸细胞凋亡指数上升,差异有统计学意义（p<0.01）;LF组和HF组Grp78、Caspase-12、Caspase-3基因表达水平上升,差异有统计学意义（p<0.05或p<0.01）.结果提示,除氧化应激以外,Caspase-12和Caspase-3基因表达异常可能是氟暴露致小鼠睾丸细胞凋亡异常的分子机制之一.     

基于AIS轨迹修复的船舶排放空间表征改进方法与应用

基于船舶自动识别系统（Automatic Identification System,AIS）数据表征船舶排放是目前船舶排放空间表征的主流方法,但AIS船舶轨迹点缺失会造成船舶排放量低估和船舶空间分布表征错误,进而影响船舶排放控制区的划分.为改进船舶排放空间表征,本研究以2013年广东省AIS船舶数据为例,采用基于时间和经纬度的三次样条方法对AIS船舶轨迹进行修复,结合动力法计算船舶排放,分析对比AIS轨迹修复前后船舶排放表征的差异,并利用空气质量模型和卫星观测评估AIS轨迹修复对船舶排放表征和广东沿海空气质量模拟的改进效果.结果表明：轨迹修复后广东省海域船舶轨迹点总数由4685773个增至5746664个,船舶NO_x排放量增加了0.6%.对于轨迹点与排放缺失集中的粤东海域,轨迹修复后船舶轨迹点数增加了88%,NO_x排放量在广东省船舶排放量的占比提升至22%,特别是在粤东重点修复海域NO_x排放量增加了2.7倍.原始轨迹在广东省海域较为稀疏,在粤东海域有明显轨迹缺失;轨迹修复后广东省海域船舶轨迹更为密集,粤东海域船舶轨迹得以补充,船舶排放空间分布更连贯.对比模拟结果与卫星观测结果,轨迹修复后粤东重点修复海域船舶模拟浓度与观测浓度的偏差由51%减至6%,总体上船舶排放模拟结果更接近卫星观测结果.     

金属改性对SAPO-34低温还原NO性能的影响

采用浸渍法制备金属改性SAPO-34分子筛催化剂,分析比较了不同单金属（Cu或Co）及不同比例双金属（Cu：Co=1：1、3：1、5：1,质量比）改性催化剂对NO的催化还原性能,评价了不同催化剂的N₂选择性,并采用扫描电子显微镜（SEM）、比表面积测试、X射线衍射分析（XRD）、NH₃-程序升温脱附（NH₃-TPD）等表征手段对催化剂的物化性能进行了分析.结果表明,单金属Cu改性催化剂具有较宽的温度区间,在250~450℃范围内NO的转化率始终保持在100%;双金属改性使NO转化率保持为100%的最低温度下降了25~50℃,显著拓宽了低温段窗口,其中,Cu₃Co₁/SAPO-34催化剂的低温催化还原性能最好,200℃即可实现100%的NO转化率,175℃下的转化率也高达80%以上.Cu-Co双金属改性SAPO-34分子筛催化剂具有优异的低温催化还原NO性能,具有在机动车尾气、工业废气的低温脱硝治理领域应用的潜力.     

核壳结构KNbO3@Co(OH)2的制备及其活化过一硫酸盐降解帕珠沙星的研究

制备了以KNbO₃为载体材料的Co（OH）₂复合材料并对其进行了详细的表征,分析了材料的组成成分、组成形态进而确定了其为核壳结构形貌的KNbO₃@Co（OH）₂.利用合成的样品作为催化剂活化过一硫酸盐（peroxymonosulfate,PMS）来降解帕珠沙星（pazufloxacin,PZF）,结果表明制备的催化剂对PZF的去除效率显著增加.讨论了不同初始PMS剂量对降解效率的影响,发现随着PMS增加可活化生成更多的硫酸根自由基（sulfate radicals,SO₄^·-）和羟基自由基（hydroxyl radicals,HO^·）来降解PZF,但继续增大PMS用量降解效率未见明显提升.酸性和中性pH值条件下利于反应活化PMS降解PZF,而碱性体系减缓反应,甚至强碱体系更易形成Co（OH）₂沉淀不利于反应体系中活性组分CoOH⁺的形成,大大抑制了催化性能.此外,在体系中加入淬灭剂叔丁醇（tert-Butanol,TBA）或者乙醇（ethanol,ETOH）进行自由基的淬灭实验,结果表明SO₄^·-自由基为体系降解PZF过程中主要贡献的自由基,而HO^·自由基的贡献较少.催化剂具有较好的稳定性5次循环之后仍能在10 min之内完全去除PZF.本研究提出了新的思路为制备其他载体的Co（OH）₂核壳结构提供参考依据,同时将该催化剂结合高级氧化技术应用到水体新兴有机污染物净化领域具有很好的应用前景.     

海绵城市透水砖铺装系统雨水入渗及重金属污染物迁移模拟

海绵城市透水砖铺装系统（PBPS）入渗特征是产流控制及径流污染物去除的重要影响因素之一。通过渗流实验,构建系统土壤层土水特征曲线,建立降雨入渗及径流重金属污染物迁移数学模型,以阐明找平层土壤粒径、基层与垫层厚度比对产流时间及径流重金属污染物去除的影响。研究表明:综合考虑延迟产流与径流重金属去除能力,中砂作为找平层介质最佳;依据结构层出水重金属污染物浓度,基层与垫层厚度比为15∶4时,PBPS对径流中重金属污染物吸附效率最高、去除效果较好。     

二乙烯三胺五甲叉膦酸酸解磷尾矿的实验探究

为减少磷尾矿堆积带来的环境污染问题,实现磷尾矿的钙、镁、磷元素的分离,以高镁磷尾矿为原料,采用二乙烯三胺五甲叉膦酸(DTPMP)进行酸解,探究磷尾矿中主要物相在DTPMP中的分解机制,并通过单因素实验探究pH、反应时间、反应温度及投料比对磷尾矿中MgO、CaO和P_2O_5分解率的影响。实验结果表明:pH对P_2O_5的分解率影响较大,高温更有利于尾矿中镁的溶出,在pH为2. 5,反应时间为60 min,反应温度为80℃,投料比为1. 56时,MgO、CaO和P_2O_5的分解率分别达到61. 05%、38. 23%和9. 67%。     

建筑垃圾堆放点样本集构建与优化研究

为更好地解决手工制作的建筑垃圾堆放点样本集效率低、数据量少,难以支撑基于深度学习的遥感图像目标检测算法训练需求的问题,采用基于像素的遥感分类方法构建建筑垃圾堆放点样本集,在此基础上结合直方图均衡化,CS-LBP算子约束以及迁移学习的方法对Wasserstein生成对抗模型（WGAN）进行优化,实现了样本集扩充。研究结果表明:相对于纯手工制作的样本集,基于像素的遥感分类方法可以显著提升样本集制作的效率;同时,经过WGAN优化后,生成样本模拟了原始数据的颜色与纹理特征分布规律,增加了原始数据的多样性,满足了扩充样本集的需求。     

On-going nitrification in chloraminated drinking water distribution system (DWDS) is conditioned by hydraulics and disinfection strategies

Within the drinking water distribution system (DWDS) using chloramine as disinfectant, nitrification caused by nitrifying bacteria is increasingly becoming a concern as it poses a great challenge for maintaining water quality. To investigate efficient control strategies, operational conditions including hydraulic regimes and disinfectant scenarios were controlled within a flow cell experimental facility. Two test phases were conducted to investigate the effects on the extent of nitrification of three flow rates (Q = 2, 6, and 10 L/min) and four disinfection scenarios (total Cl₂=1 mg/L, Cl₂/NH₃-N=3:1; total Cl₂=1 mg/L, Cl₂/NH₃-N=5:1; total Cl₂=5 mg/L, Cl₂/NH₃-N=3:1; and total Cl₂=5 mg/L, Cl₂/NH₃-N=5:1). Physico-chemical parameters and nitrification indicators were monitored during the tests. The characteristics of biofilm extracellular polymetric substance (EPS) were evaluated after the experiment. The main results from the study indicate that nitrification is affected by hydraulic conditions and the process tends to be severe when the fluid flow transforms from laminar to turbulent (2300<Re<4000). Increasing disinfectant concentration and optimizing Cl₂/NH₃-N mass ratio were found to inhibit nitrification to some extend when the system was running at turbulent condition (Q = 10 L/min, Re = 5535). EPS extracted from biofilm that was established at the flow rate of 6 L/min had greater carbohydrate/protein ratio. Furthermore, several nitrification indicators were evaluated for their prediction efficiency and the results suggest that the change of nitrite, together with total organic carbon (TOC) and turbidity can indicate nitrification potential efficiently.     

Chemical characteristics of road dust PM2.5 fraction in oasis cities at the margin of Tarim Basin

In order to understand the compositions characteristics of particulate matter with aerodynamic diameter less than 2.5 μm (PM_2.5) fraction in road dust (RD_2.5) of oasis cities on the edge of Tarim Basin, 30 road dust (RD) samples were collected in Kashi, Cele, and Yutian in the spring, 2018, and RD_2.5 was collected using the resuspension approach. Eight water-soluble ions, 39 trace elements and 8 fractions of carbon-containing species in PM_2.5 were analyzed. Ca²⁺ and Ca were the most abundant ions and elements in RD_2.5 (7.1% and 9.5%). Cl^- in RD_2.5 was affected not only by attributed to saline-alkali soils in oasis cities of the Tarim Basin and dust from Taklimakan Desert but also by human activities. Moreover, the organic carbon/elemental carbon (OC/EC) ratio indicated that carbon components in RD_2.5 in Cele town mainly come from fossil fuel combustion, while those in Yutian and Kashi mainly come from biomass combustion. It is noteworthy that high Ca in RD_2.5 was seriously affected by anthropogenic emissions, and high Na and K contents in RD_2.5 could be derived from soil and desert dust. It was estimated that Cd, Tl, Sn and Cr were emitted from anthropogenic emissions using the enrichment factor. The coefficients of divergence (COD) result indicated that the influence of local emission on road dust emission is greater than that of long-distance transmission. This study is the first time to comprehensively analyze the chemical characteristics of road dust in oasis cities, and the results provides the sources of road dust at the margin of Tarim Basin.