Investigation of aerosol and gas emissions from a coal-fired power plant under various operating conditions

The concentrations of fine particles and selected gas pollutants in the flue gas entering the stack were measured under several common operation modes in an operating coal power plant producing electricity. Particle size distributions in a diameter range from 10 nm to 20 μm were measured by a scanning mobility particle sizer (SMPS), and the flue gas temperature and concentrations of CO₂ and SO₂ were monitored by a continuous emission monitoring system (CEMS). During the test campaign, five plant operating modes were studied: soot blowing, bypass of flue-gas desulfurization (FGD), reheat burner operating at 0% (turned off), 27%, and 42% (normal condition) of its full capacity. For wet and dry aerosols, the measured mode sizes were both around 40 nm, but remarkable differences were observed in the number concentrations (#/cm³, count per square centimeter). A prototype photoionizer enhanced electrostatic precipitator (ESP) showed improved removal efficiency of wet particles at voltages above +11.0 kV. Soot blowing and FGD bypass both increased the total particle number concentration in the flue gas. The temperature was slightly increased by the FGD bypass mode and varied significantly as the rating of reheat burner changed. The variations of CO₂ and SO₂ emissions showed correlations with the trend of total particle number concentration possibly due to the transitions between gas and particle phases. The results are useful in developing coal-fired power plant operation strategies to control fine particle emissions and developing amine-based CO₂ capture technologies without operating and environmental concerns associated with volatile amine emissions.

Implications: The measurement of the fine particle size distributions in the exhaust gas under several common operating conditions of a coal-fired power plant revealed different response relations between aerosol number concentration and the operating condition. A photo-ionizer enhanced ESP was demonstrated to capture fine particles with higher efficiency compared to conventional ESPs, and the removal efficiency increased with the applied voltage. The characteristic information of aerosols and main gaseous pollutants in the exhaust gas is extremely important for developing and deploying CO₂ scrubbers, whose amine emissions and operating effectiveness depends greatly on the upstream concentrations of fine particles, SO₂, from the power plant.     

The effect of diesel fuel sulfur content on particulate matter emissions for a nonroad diesel generator

The effect of sulfur content on diesel particulate matter (DPM) emissions was studied using a diesel generator (Generac Model SD080, rated at 80 kW) as the emission source to simulate nonroad diesel emissions. A load simulator was used to apply loads to the generator at 0, 25, 50, and 75 kW, respectively. Three diesel fuels containing 500, 2100, and 3700 ppm sulfur by weight were selected as generator fuels. The U.S. Environmental Protection Agency sampling Method 5 "Determination of Particulate Matter Emissions from Stationary Sources" together with Method 1A "Sample and Velocity Traverses for Stationary Sources with Small Stacks or Ducts" was adopted as a reference method for measurement of the exhaust gas flow rate and DPM mass concentration. The effects of various parameters on DPM concentration have been studied, such as fuel sulfur contents, engine loads, and fuel usage rates. The increase of average DPM concentrations from 3.9 mg/Nm3 (n cubic meter) at 0 kW to 36.8 mg/Nm3 at 75 kW is strongly correlated with the increase of applied loads and sulfur content in the diesel fuel, whereas the fuel consumption rates are only a function of applied loads. An empirical correlation for estimating DPM concentration is obtained when fuel sulfur content and engine loads are known for these types of generators: Y = Zm(alphaX + beta), where Y is the DPM concentration, mg/m3, Z is the fuel sulfur content, ppm(w) (limited to 500-3700 ppm(w)), X is the applied load, kW, m is the constant, 0.407, alpha and beta are the numerical coefficients, 0.0118 +/- 0.0028 (95% confidence interval) and 0.4535 +/- 0.1288 (95% confidence interval), respectively.     

Influence of air pollution on the incidence of respiratory tract neoplasm

To evaluate the possible influence of air pollutants on the incidence of respiratory tract neoplasm we studied 12 S?o Paulo City districts where air pollution is observed. We collected data on pollutants from 1981-1990 and correlated it with the incidence of larynx and lung neoplasms in 1997. Ozone was the pollutant that best correlated with the incidence of neoplasm. The correlation coefficients were 0.7234 (p=0.277) and 0.9929 (p=0.007) for lung and larynx cancer, respectively. There may be a relationship between air pollution and the incidence of respiratory tract neoplasm. This study, however, does not allow us to conclude that there is a causal relationship.     

Catalytic decomposition of hydrogen peroxide and 4-chlorophenol in the presence of modified activated carbons

The objective of this research was to examine the heterogeneous catalytic decomposition of H(2)O(2) and 4-chlorophenol (4-CP) in the presence of activated carbons modified with chemical pretreatments. The decomposition of H(2)O(2) was suppressed significantly by the change of surface properties including the decreased pH(pzc) modified with oxidizing agent and the reduced active sites occupied by the adsorption of 4-CP. The apparent reaction rate of H(2)O(2) decomposition was dominated by the intrinsic reaction rates on the surface of activated carbon rather than the mass transfer rate of H(2)O(2) to the solid surface. By the detection of chloride ion in suspension, the reduction of 4-CP was not only attributed to the advanced adsorption but also the degradation of 4-CP. The catalytic activity toward 4-CP for the activated carbon followed the inverse sequence of the activity toward H(2)O(2), suggesting that acidic surface functional group could retard the H(2)O(2) loss and reduce the effect of surface scavenging resulting in the increase of the 4-CP degradation efficiency. Few effective radicals were expected to react with 4-CP for the strong effect of surface scavenging, which could explain why the degradation rate of 4-CP observed in this study was so slow and the dechlorination efficiency was independent of the 4-CP concentration in aqueous phase. Results show that the combination of H(2)O(2) and granular activated carbon (GAC) did increase the total removal of 4-CP than that by single GAC adsorption.     

一种新型国产高效除尘滤筒在船厂分段涂装车间的应用

国产除尘滤材是将聚酯纤维热轧成型 ,再涂敷高分子发泡制成。滤材硬挺、耐压、抗撕裂 ,内部结构稳定 ,粉尘过滤精度高 ,实现表面过滤 ,易清灰再生 ,使用寿命长 ,耐水、酸、碱 ,可广泛用于各工业领域的气体净化和粉尘处理。大连新船重工集团把国产除尘滤材制成的滤筒配置到厂内原有的除尘系统中 ,通过 1年多的使用 ,获得非常满意的除尘效果。从而证明国产滤料性能已达到国际先进水平。     

农药毒死蜱的生态风险及其微生物修复技术研究进展

毒死蜱是替代甲胺磷和对硫磷等高毒农药的高效有机磷杀虫剂,在世界范围得到广泛使用.但是,环境毒理学研究发现,毒死蜱对生态环境具有潜在的危险性,甚至被认为具有干扰内分泌的功能,许多国家对毒死蜱在农产品中的残留量有严格的规定.因此,深入研究毒死蜱的生态风险问题是当务之急.对国内外关于毒死蜱的残留活性、生态毒理、降解机制以及生物修复等方面的研究进行了综述,以期对毒死蜱的合理管理和使用提供科学依据.     

盘式曝气器的结构优化设计

盘式曝气器是目前城市污水处理厂主要采用的曝气设备之一.但目前盘式曝气器存在充氧能力低、阻力损失大、使用寿命短等技术问题,增加了城市污水处理厂运行成本,降低了运行效能.针对这些问题,对盘式曝气器进行了结构优化设计.通过结构优化,既改善了曝气器的抗撕裂性和自闭性,同时又提高了充氧能力,降低了曝气阻力损失.     

膨润土对Pb2+、Cu2+、Cr3+的吸附动力学及等温线研究

研究所用膨润土的主要成分为SiO2和Al2O3,属于Ca基膨润土,BET表面积为50.83 m2/g.在恒温及恒定pH条件下,用静态吸附法研究了膨润土对Pb2 、Cu2 、Cr3 的吸附特性,结果表明其较好地符合Lagergten二级吸附速率方程,对这3种离子的吸附速率为Pb2 ＞Cu2 ＞Cr3 .利用3种等温线方程对吸附过程进行拟合,发现利用Langmuir吸附等温方程计算的值与膨润土吸附Pb2 、Cu2 、Cr3 试验数据最为吻合.膨润土对3种金属离子的平衡吸附量为Cr3 ＞Cu2 ＞Pb2 .     

可张孔曝气器曝气能耗试验研究

通过试验研究,总结出可张孔曝气阻力损失的影响因素,以优化产品的结构设计参数,降低产品在工程应用中的能耗,获取更好的经济效益。