Fe^0-厌氧微生物体系处理活性艳红X-3B的试验研究

采用间歇式摇床试验,研究了葡萄糖共基质条件下Fe^0-厌氧微生物体系中Fe^0投加量、pH值、染料初始浓度对活性艳红X-3B模拟废水脱色率的影响,比较了Fe^0-厌氧微生物、纯厌氧微生物及纯Fe^0 3种体系中废水的脱色效果。结果表明：Fe^0-厌氧微生物体系中初始浓度（50～500mg／L）对活性艳红X-3B的脱色率影响不大;而Fe^0投加量、pH值存在一个最佳范围;当Fe^0投加量为260mg／L,pH值为6．0,污泥浓度为0．35gVSS／L,停留时间约为30h时,体系中活性艳红X-3B的脱色率可达90％左右,比相同试验条件下纯Fe^0、纯厌氧微生物体系达到此脱色率所需时间分别缩短了约1／2、7／10。在Fe^0-厌氧微生物体系中,由紫外可见分光光度分析可推测活性艳红X-3B的脱色机理主要是其偶氮键发生断裂,生成苯胺和萘类物质,而且苯胺和萘类物质能得到进一步降解。     

Measurement of gas-phase total peroxides at the summit of Mount Tai in China

Measurement of ambient gas-phase total peroxides was performed at the summit of Mount Tai (Mt. Tai, 1534 m above sea level) in central-eastern China during March 22–April 24 and June 16–July 20, 2007. The hourly averaged concentration of peroxides was 0.17 ppbv (± 0.16 ppbv, maximum: 1.28 ppbv) and 0.55 ppbv (± 0.67 ppbv, maximum: 3.55 ppbv) in the spring and summer campaigns, respectively. The average concentration of peroxides at Mt. Tai, which is in a heavily polluted region, was much lower than hydrogen peroxide measurements made at some rural mountain sites, suggesting that significant removal processes took place in this region. An examination of diurnal variation and a correlation analysis suggest that these removal processes could include chemical suppression of peroxide production due to the scavenging of peroxy and hydroxy radicals by high NO_x, wet removal by clouds/fogs rich in dissolved sulfur dioxide which reacts quickly with peroxides, and photolysis. These sinks competed with photochemical sources of peroxides, resulting in different mean concentrations and diurnal pattern of peroxides in the spring and summer. A principal component analysis was conducted to quantify the major processes that influenced the variation of peroxide concentrations. This analysis shows that in the spring photochemical production was an important source of peroxides, and the major sink was scavenging during upslope transport of polluted and humid air from the lower part of the planetary boundary layer (PBL) and wet removal by synoptic scale clouds. During the summer, highly polluted PBL air (with high NO_x) was often associated with very low peroxides due to the chemical suppression of HO₂ by high NO_x and wet-removal by clouds/fogs in this sulfur-rich atmosphere, especially during the daytime. Higher concentrations of peroxides, which often appeared at mid-nighttime, were mainly associated with subsidence of air masses containing relatively lower concentrations of NO_y.     

Carbon isotope analysis for source identification of atmospheric formaldehyde and acetaldehyde in Dinghushan Biosphere Reserve in South China

Formaldehyde and acetaldehyde are two most abundant carbonyls in ambient air. Biogenic emission has been proposed as a significant source other than anthropogenic emissions and atmospheric secondary formation. Here at a forest site in South China, the carbon isotopic compositions of formaldehyde and acetaldehyde emitted from leaves of three tree species (Litsea rotundifolia, Canarium album and Castanea henryi) were measured in comparison with the bulk carbon isotopic compositions of tree leaves. δ¹³C data of the emitted aldehydes (from ?31‰ to ?46‰) were quite different for tree species, which were all more depleted in ¹³C than the tree-leaf bulk δ¹³C values (from ?27‰ to ?32‰). Formaldehyde in ambient air at the forest site had δ¹³C values different from those of leaf-emitted formaldehyde, indicating other sources for ambient formaldehyde apart from direct emission from leaves, most probably the photooxidation of biogenic hydrocarbon like isoprene and monoterpene. The δ¹³C differences of acetaldehyde between ambient data and those of tree leaves emission were less than 1‰, implying direct biogenic emission as the dominant source.     

Comparison of homologous and heterologous formats in nanocolloidal gold-based immunoassays for parathion residue determination

The effectiveness of homologous and heterologous formats in a nanocolloidal gold-based immunoassay for pesticide residue determination was investigated. Parathion, one of the most toxic organophosphorus pesticides, was used as the target analyte. One-step homologous and heterologous test strips based on a nanocolloidal gold-labeled monoclonal antibody were developed for the rapid detection of parathion residues. The results showed that the heterologous format was more effective than the homologous format, being more sensitive, more specific to parathion and more tolerant of matrix interferences. The best competitive hapten was found to have a moderate heterology and the opposite electronic distribution to the immunizing hapten. The detection limits for parathion using the preferred heterologous strip were 1 μg/L in water samples and 5 μg/kg in soil and food samples.     

不同粒径零价铁（ZVI）对污水污泥H_2S和CH_4释放速率的影响

考察了不同粒径零价铁（ZVI）,包括200目普通铁粉（200m-ZVI）、800目超细铁粉（800m-ZVI）和纳米铁粉（nZVI,粒径=20 nm）,对污水污泥的硫化氢和甲烷释放速率的影响。研究发现：（1）在22 d内,添加0.1%的200m-ZVI使污泥的硫化氢释放速率提高48.0%,而添加0.1%的800-ZVI和nZVI,则使污泥的硫化氢释放速率分别降低33.1%和77.1%;（2）不同粒径ZVI均可以提高污泥沼气中的甲烷浓度,且依次为nZVI〉800m-ZVI〉200m-ZVI;（3）在23 d内,添加0.1%的200m-ZVI和nZVI使污泥的甲烷累计产生量分别提高了15.5%和40.6%,而添加0.1%800m-ZVI则使甲烷产生量降低了12.5%。nZVI可以有效控制污泥的硫化氢释放,并显著提升污泥在厌氧发酵过程的产甲烷速率。     

微波诱导AC/Cu、AC/Fe催化非均相Fenton 反应催化降解垃圾渗滤液

采用活性炭载体负载Cu、Fe为催化剂,在微波诱导作用下,对垃圾渗滤液污染物进行降解。实验结果表明,活性炭负载金属前经适当浓度硝酸浸泡处理后,催化剂对COD去除率提高可超过15%,过高硝酸盐浓度对COD去除有不利影响;催化剂对COD去除率随Cu、Fe金属负载量增加呈先增加后降低的趋势,催化剂对Cu、Fe的最佳负载量分别为质量百分比2.11%和1.12%。对于AC-Cu体系,在初始pH=3,H2O2投加量为4.98×103mg/L,催化剂用量为5.0×103mg/L,420 W功率下微波辐射10 min时,垃圾渗滤液COD去除率可达到84.13%;对于AC-Fe体系,当H2O2投加量为0.33×103mg/L,催化剂AC-Fe用量为2.0×104mg/L,420 W功率下微波作用10 min时,垃圾渗滤液COD去除率为60.16%。分析2种催化剂对COD去除差异的原因,可能是催化剂AC-Cu表面单分子分布的阈值比AC-Fe高。降解液的pH值对AC-Cu体系、AC-Fe体系COD去除影响存在拐点,最高COD去除率点对应的降解液pH值为3。微波辐射功率较低时,体系COD去除率随辐射功率增加而增加;辐射功率较高时,高温下垃圾渗滤液中有机硫化物分解成小分子硫化物,对催化剂活性存在一定抑制作用。     

Heterogeneous photocatalytic degradation of methyl orange in schwertmannite/oxalate suspension under UV irradiation

Introduction

Schwertmannite was synthesized through an oxidation of FeSO₄ by Acidithiobacillus ferrooxidans LX5 cell suspension at an initial pH?2.5 and 28°C for 3?days and characterized using X-ray diffraction spectroscopy and scanning electron microscope. The schwertmannite photocatalytic degradation of methyl orange (MO) by oxalate was investigated at different initial pH values, concentrations of schwertmannite, oxalate, and MO.

Results

The results demonstrated that photodegradation of MO in the presence of schwertmannite or oxalate alone was very weak. However, the removal of MO was significantly enhanced when schwertmannite and oxalate coexisted in the reaction system. Low pH (4 or less) was beneficial to the degradation of MO. The optimal doses of schwertmannite and oxalate were 0.2?g?L^?1 and 2?mM, respectively. Hydroxyl radicals (·OH) and Fe(II), the intermediate products, were also examined during the reaction to explore their correlation with the degradation of MO.

Conclusion

A possible mechanism for the photocatalytic decomposition of MO in the study was proposed. The formation of Fe(III)-oxalate complexes on the surface of schwertmannite was a precursor of H₂O₂ and Fe(II) production, further leading to the yield of ·OH responsible for the decomposition of MO.     

Enhanced degradation of azo dye alizarin yellow R in a combined process of iron–carbon microelectrolysis and aerobic bio-contact oxidation

Purpose

With the aim of enhanced degradation of azo dye alizarin yellow R (AY) and further removal of the low-strength recalcitrant matter (LsRM) of the secondary effluent as much as possible, our research focused on the combination of aerobic bio-contact oxidation (ABO) with iron/carbon microelectrolysis (ICME) process.

Materials and methods

The combined ABO (with effective volume of 2.4?l) and ICME (with effectively volume of 0.4?l) process were studied with relatively short hydraulic retention time (HRT) of 4 or 6?h.

Results

At the HRT of 6?h with the reflux ratio of 1 and 2, the AY degradation efficiency in the final effluent was >96.5%, and the total organic carbon (TOC) removal efficiency were 69.86% and 79.44%, respectively. At the HRT of 4?h and the reflux ratio of 2, TOC removal efficiency and AY degradation efficiency were 73.94% and 94.89%, respectively. The ICME process obviously enhanced the total AY removal and the generated micromolecule acids and aldehydes then that wastewater backflow to the ABO where they were further biodegraded.

Conclusion

The present research might provide the potential options for the advanced treatment azo dyes wastewater with short HRT and acceptable running costs.     

Toxicological effect of MPA-CdSe QDs exposure on zebrafish embryo and larvae

Cadmium selenium (CdSe) quantum dots (QDs) are semiconductor nanocrystals that hold wide range of applications and substantial production volumes. Due to unique composition and nanoscale properties, their potential toxicity to aquatic organisms has increasingly gained a great amount of interest. However, the impact of CdSe QDs exposure on zebrafish embryo and larvae remains almost unknown. Therefore, the lab study was performed to determine the developmental and behavioral toxicities to zebrafish under continuous exposure to low level CdSe QDs (0.05-31.25 mg L⁻¹) coated with mercaptopropionic acid (MPA). The results showed MPA-CdSe exposure from embryo to larvae stage affected overall fitness. Our findings for the first time revealed that: (1) The 120 h LC₅₀ of MPA-CdSe for zebrafish was 1.98 mg L⁻¹; (2) embryos exposed to MPA-CdSe resulted in malformations incidence and lower hatch rate; (3) abnormal vascular of FLI-1 transgenic zebrafish larvae appeared after exposure to MPA-CdSe including vascular junction, bifurcation, crossing and particle appearance; (4) larvae behavior assessment showed during MPA-CdSe exposure a rapid transition from light-to-dark elicited a similar, brief burst and a higher basal swimming rate; (5) MPA-CdSe induced embryos cell apoptosis in the head and tail region. Results of the observations provide a basic understanding of MPA-CdSe toxicity to aquatic organisms and suggest the need for additional research to identify the toxicological mechanism.     

阴极液及底物浓度对AFB-MFC同步废水处理及产电性能影响

为了提高厌氧流化床微生物燃料电池（AFB-MFC）的性能,并为双室MFC寻找价廉、易得、无污染的阴极液,在曝气量16～24 L/h、温度（35±2）℃、回流量10.2 L/h、阴极底边距阴极室内底部17.3 cm、外电阻250 Ω、水力停留时间（HRT）14.0～14.9 h以及进水pH 7.81～8.37下,研究了阴极液及底物浓度对系统产电及废水处理性能的影响。结果表明,使用缓冲溶液、阳极室出水和自来水作阴极液时,自来水的产电性能最佳,阴极液种类不影响系统有机基质的去除。以自来水为阴极液时,阴极液pH及电导率随运行时间增加而增加,COD去除率为80.11%～89.29%,输出电压及功率密度开始随运行时间增加而增加,之后稳定在440～452 mV和48.40～51.08 mW/m²之间。增加底物浓度对COD去除率影响不大,而输出电压及功率密度随底物浓度增加而下降;底物COD浓度由3 307.09 mg/L增至9 520 mg/L时,COD去除率在85.77%～94.44%之间,输出电压及功率密度则分别由449 mV和50.40 mW/m²下降至406 mV和41.21 mW/m²。自来水作阴极液可避免二次污染及阴极液对阳极室微生物的影响,并得到高的产电能力。