Treatability studies of naphthalene in soil,water and air with persulfate activated by iron(Ⅱ)

Chemical oxidation was applied to an artificially contaminated soil with naphthalene (NAP). Evaluation of NAP distribution and mass reduction in soil, water and air phases was carried out through mass balance. Evaluation of NAP distribution and mass reduction in soil, water and air phases was carried out through mass balance. The importance of the air phase analysis was emphasized by demonstrating how NAP behaves in a sealed system over a 4 hr reaction period. Design of Experiments method was applied to the following variables: sodium persulfate concentration [SP], ferrous sulfate concentration [FeSO₄], and pH. The system operated with a prefixed solid to liquid ratio of 1:2. The following conditions resulted in optimum NAP removal [SP] = 18.37 g/L, [FeSO₄] = 4.25 g/L and pH = 3.00. At the end of the 4 hr reaction, 62% of NAP was degraded. In the soil phase, the chemical oxidation reduced the NAP concentration thus achieving levels which comply with Brazilian and USA environmental legislations. Besides the NAP partitioning view, the monitoring of each phase allowed the variabilities assessment over the process, refining the knowledge of mass reduction. Based on NAP distribution in the system, this study demonstrates the importance of evaluating the presence of semi-volatile and volatile organic compounds in the air phase during remediation, so that there is greater control of the system as to the distribution and presence of the contaminant in the environment. The results highlight the importance of treating the contaminant in all its phases at the contaminated site.     

Characterization of atmospheric aerosol (PM10 and PM2.5) from a medium sized city in São Paulo state, Brazil

Air pollution causes deleterious effects on human health with aerosols being among the most polluting agents.The objective of this work is the characterization of the PM_(2.5) and PM_(10) aerosol mass in the atmosphere.The methods of analysis include WD-XRF and EDS.Data were correlated with meteorological information and air mass trajectories(model HYSPLIT)by multivariate analysis.A morphological structural analysis was also carried out to identify the probable sources of atmospheric aerosols in the city of Sao Jose do Rio Preto,Brazil.The mean mass concentration values obtained were 24.54 μg/m~3 for PM_(10),above the WHO annual standard value of 20 μg/m~3 and 10.88 μg/m~3 for PM_(2.5) whose WHO recommended limit is10 μg/m~3.WD-XRF analysis of the samples revealed Si and Al as major components of the coarse fraction.In the fine fraction,the major elements were Al and S.The SEM-FEG characterization allowed identifying the morphology of the particles in agglomerates,ellipsoids and filaments in the PM_(10),besides spherical in the PM_(2.5).The analysis by EDS corroborated WD-XRF results,identifying the crustal elements,aluminosilicates and elements of anthropogenic origin in the coarse fraction.For the fine fraction crustal elements were also identified;aluminosilicates,black carbon and spherical particles(C and O) originating from combustion processes were predominant.The use of multivariate analysis to correlate air mass trajectories with the results of the morpho-structural characterization of the particulate matter allowed confirmation of the complex composition of the particles resulting from the combination of both local and long-distance sources.     

Reactive uptake of NO2 on volcanic particles: A possible source of HONO in the atmosphere

The heterogeneous degradation of nitrogen dioxide (NO₂) on five samples of natural Icelandic volcanic particles has been investigated. Laboratory experiments were carried out under simulated atmospheric conditions using a coated wall flow tube (CWFT). The CWFT reactor was coupled to a blue light nitrogen oxides analyzer (NO_x analyzer), and a long path absorption photometer (LOPAP) to monitor in real time the concentrations of NO₂, NO and HONO, respectively. Under dark and ambient relative humidity conditions, the steady state uptake coefficients of NO₂ varied significantly between the volcanic samples probably due to differences in magma composition and morphological variation related with the density of surface OH groups. The irradiation of the surface with simulated sunlight enhanced the uptake coefficients by a factor of three indicating that photo-induced processes on the surface of the dust occur. Furthermore, the product yields of NO and HONO were determined under both dark and simulated sunlight conditions. The relative humidity was found to influence the distribution of gaseous products, promoting the formation of gaseous HONO. A detailed reaction mechanism is proposed that supports our experimental observations. Regarding the atmospheric implications, our results suggest that the NO₂ degradation on volcanic particles and the corresponding formation of HONO is expected to be significant during volcanic dust storms or after a volcanic eruption.     

短期干旱胁迫对马尾松排放挥发性有机物的影响

为探究干旱环境对BVOCs排放的影响,应用动态封闭式采样系统和热脱附-气相色谱-飞行质谱仪,对短期干旱胁迫作用下马尾松的BVOCs排放进行了实验室测量,定量分析BVOCs排放速率和排放组成的变化.结果表明,干旱胁迫时异戊二烯的排放受到抑制,排放速率降低约50%;单萜烯和倍半萜烯的排放水平增强,排放速率分别为137.85和0.98μg/（m²·h）,是未受胁迫时的2.9和2.0倍.除反式-α-香柠檬烯外,干旱胁迫促进各单萜烯和倍半萜烯化合物的排放,是未受胁迫时的1.3~42.4倍,其中3-蒈烯排放的响应最敏感,α-葑烯、α-水芹烯和石竹烯的响应最弱.干旱胁迫时单萜烯和倍半萜烯的排放组成有所变化,但主导的化合物种类不变,单萜烯以α-蒎烯、香桧烯和β-蒎烯为主,占比分别为48%、17%和17%;倍半萜烯以石竹烯和长叶烯为主,占比分别为57%和34%.     

Mercury levels in human population from a mining district in Western Colombia

A biomonitoring study was carried out to examine the adverse impacts of total mercury in the blood(HgB), urine(Hg U) and human scalp hair(HgH) on the residents of a mining district in Colombia. Representative biological samples(scalp hair, urine and blood) were collected from volunteered participants(n = 63) to estimate the exposure levels of THg using a Direct mercury analyzer. The geometric mean of THg concentrations in the hair,urine and blood of males were 15.98 μg/g, 23.89 μg/L and 11.29 μg/L respectively, whereas the females presented values of 8.55 μg/g, 5.37 μg/L and 8.80 μg/L. Chronic urinary Hg(HgU)levels observed in male workers(32.53 μg/L) are attributed to their long termed exposures to inorganic and metallic mercury from gold panning activities. On an average, the levels of THg are increasing from blood(10.05 μg/L) to hair(12.27 μg/g) to urine(14.63 μg/L).Significant positive correlation was found between hair and blood urinary levels in both male and female individuals. Thus the present biomonitoring investigation to evaluate the Hg levels and associated health issues would positively form a framework for further developmental plans and policies in building an ecofriendly ecosystem.     

Shelter, housing and recovery: a comparison of u.s. Disasters

In this paper we examine the issues associated with the temporary sheltering and housing of victims after natural disasters in the United States. Specific topics addressed include differential access to shelter and housing aid according to social class, ethnicity and related demographic factors; the relationship between post-disaster shelter and housing and long-term recovery; the role of social support networks in the sheltering of victims; and the implications of the research for the provision of shelter and housing aid after disasters.     

The influence of pH on cadmium toxicity to the green alga Stichococcus bacillaris and on the cadmium forms present in the culture medium

Cadmium toxicity to the green alga Stichococcus bacillaris was investigated in media of pH 3-9. A significant decrease of cadmium toxicity occurred in both the acidic and alkaline ranges of pH. In media of pH 3 and 9, cadmium did not affect the dry mass content substantially. Maximum toxicity of cadmium was noticed at pH 6-7. Voltametric investigations showed a significant effect of pH on electrochemically measured cadmium content in the culture media. Hydrolysis of the medium components and formation of cadmium complexes with OH(-) ions caused a considerable decrease in amounts of electrochemically measured cadmium in the alkaline range of pH.     

Recycling of petroleum-contaminated sand

The environmental impact of using petroleum-contaminated sand (PCS) as a substitute in asphalt paving mixtures was examined. An appreciable component of PCS is oily sludge, which is found as the dregs in oil storage tanks and is also produced as a result of oil spills on clean sand. The current method for the disposal of oily sludge is land farming. However, this method has not been successful as an oil content of < 1% w/w is required, and difficulty was encountered in reaching this target. The reuse of the sludge in asphalt paving mixtures was therefore considered as an alternative. Standard tests and environmental studies were conducted to establish the integrity of the materials containing the recycled sludge. These included physical and chemical characterization of the sludge itself, and an assessment of the mechanical properties of materials containing 0%, 5%, 22% and 50% oily sludge. The blended mixtures were subjected to special tests, such as Marshall testing and the determination of stability and flow properties. The experimental results indicated that mixtures containing up to 22% oily sludge could meet the necessary criteria for a specific asphalt concrete wearing course or bituminous base course. To maximize the assay from the recycled material, the environmental assessment was restricted to the 50% oily sludge mixture. Leachates associated with this particular mixture were assayed for total organic residue and certain hazardous metal contaminants. The results revealed that the organics were negligible, and the concentrations of the metals were not significant. Thus, no adverse environmental impact should be anticipated from the use of the recycled product. Our research showed that the disposal of oily sludge in asphalt paving mixtures could possibly yield considerable savings per tonne of asphalt concrete, and concurrently minimize any direct impact on the environment.     

Reduction and avoidance of lubricant mist demands an integrated assessment approach

A case study to identify major factors for lubricant mist exposure covered 15 metal machining sites. The investigation included milling, turning, drilling and grinding applications. Systematic analysis considered all relevant data concerning the machine tool, the lubricant and the suction plant. The efficiency of the implemented maintenance program at the installed filter systems was checked by concentration measurements immediately before and after service. All performed measurements of lubricant aerosol and vapor loads upstream and downstream of the installed filter systems were carried out according to VDI 2066 and BIA 3110, respectively. The selection criteria for the sites to be investigated, the systematic nature of the data acquisition and the procedure of the analysis are demonstrated in detail by performing comparisons between selected applications using emulsions and those employing straight oil for lubrication. The results of the study identify recirculation of ventilated air as the major source of workplace exposure to airborne lubricant emissions. More than 60% of the demisters investigated emit air at total lubricant loads (aerosols and vapor) above the limit of 20 mg m-3 at any time of operation; which also means immediately after service. A common reason for exceeded aerosol loads in recirculated air is e.g. the fact that the type of filter system applied is often not suitable for the separation problem. Loads of lubricant vapor are usually higher at the processes which use water emulsions as lubricant. In a quarter of the cases the limits were exceeded solely due to high vapor loads even immediately after service. The exposure can be reduced by replacing the lubricant, installation of a vapor separation plant or avoiding air recirculation. Maintenance time of the demisting system and aerosol separation efficiency of state-of-the-art demisting systems can be expanded by implementation of enhanced preliminary filter stages. This study confirms that appropriate service measures lower both aerosol emissions and lubricant vapor concentrations due to the reduction of exposed oil-wetted surfaces. The performed measurements show no significant relationship between loads of airborne lubricants and the type of machining process. Therefore, investigations at a much more detailed level have to be performed. However, the individual assessment of any workplace due to the complex situation remains essential.     

The effect of filter material on bioaerosol collection of Bacillus subtilis spores used as a Bacillus anthracis simulant

The objective of this study was to determine filter materials and extraction methods that are appropriate to use for environmental sampling of B. anthracis. Four types of filters were tested: mixed cellulose ester (MCE) with a pore size of 3 microm, polytetrafluoroethylene (PTFE) with pore sizes of 1 and 3 microm, and gelatin with a pore size of 3 microm. Bacillus subtilis var. niger endospores (also known as Bacillus globigii[BG]) were used as a surrogate for B. anthracis. Endospores were collected into Button Inhalable Aerosol Samplers with sampling times of 15 minutes, 1 hour, and 4 hours. Physical collection efficiency was determined by measuring upstream and downstream B. subtilis concentrations with an optical particle counter. Vortexing with ultrasonic agitation and vortexing with shaker agitation extraction methods were evaluated. The MCE, 1 microm PTFE, and gelatin filters provided physical collection efficiencies of 94% or greater. The 3 microm PTFE filter showed inconsistent physical efficiency characteristics between filters. Epifluorescence microscopic analysis of the gelatin filter extraction fluid revealed the presence of contamination by non-culturable bacteria. Mean differences for microbial culturability were not statistically significant for filter materials and extraction methods. However, the vortexing with shaker agitation extraction method resulted in higher total microbial counts in the extraction fluids for MCE and 1 microm PTFE filters when compared to vortexing with ultrasonic agitation. In summary, the MCE and 1 microm PTFE filters in combination with vortexing and shaker extraction demonstrated the best performance for the filter collection and extraction of BG spores.