ANAMMOX富集与优化停曝比对MBR-SNAD工艺的影响

采用膜生物反应器（MBR）研究了厌氧氨氧化细菌在富集过程中的活性变化,在启动全程自养脱氮（CANON）工艺中以恒定曝气量,通过优化停曝比实现氨氧化细菌（AerAOB）和厌氧氨氧化细菌（AnAOB）协同脱氮并且有效抑制亚硝酸盐氧化菌（NOB）的活性,然后添加有机物（乙酸钠）逐步启动同步亚硝化-厌氧氨氧化耦合异养反硝化（SNAD）工艺.结果表明,在厌氧氨氧化细菌富集过程中,通过不断缩短水力停留时间（HRT）提高进水氮负荷的方式强化厌氧氨氧化细菌活性,其平均活性由0.603mgN/（h·gVSS）提高到了8.1mgN/（h·gVSS）;当恒定曝气量为50mL/min,停曝比为4：10（min：min）时,AerAOB和AnAOB对氨氮的去除量分别占总氨氮去除量的58.8%和41.2%,NOB氧化亚硝态氮的量占总硝态氮生成量的15.3%,成功抑制了NOB的活性;当C/N比为0.5,调整停曝比为4：15后,反硝化过程氮去除量占总氮去除率的20.9%,厌氧氨氧化过程氮去除量占总氮去除率的79.1%,实现了AerAOB、AnAOB和反硝化细菌（DNB）协同脱氮的目的.     

高有机负荷冲击对填料型MBR运行性能的影响

针对分散式农村生活污水有机负荷变化明显的特点,研究了填料型厌氧-缺氧-好氧膜生物反应器（A²O-MBR）抗高有机负荷的能力,考察了高有机负荷冲击对污染物去除效果、悬浮和附着污泥性质以及膜污染的影响.结果表明,高负荷冲击期间污染物去除稳定,氨氮去除率在冲击第3d从99.1%下降到78.5%,出水氨氮浓度高于5mg/L,随后去除率恢复至97.6%;悬浮和附着微生物的三磷酸腺苷（ATP）含量增加;附着生物量显著增加;细胞外聚合物（EPS）增加;高有机负荷冲击期间膜污染更严重,膜面污染层EPS含量显著增加;太阳能微动力A²O-MBR系统能减少10%的碳排放.     

新型垂直探测资料在污染天气分析中的应用

针对2017年1月上旬广州地区出现的一次持续时间长的重污染天气过程,基于地面观测资料、激光雷达、风廓线雷达和微波辐射计数据,从水平和垂直扩散条件2个方面分析了此次污染过程的形成和维持的原因.结果表明：（1）本次污染过程期间,广州地区地面风速基本为小于2m/s的偏北风,在300m高度以下普遍存在平均水平风速低于2.6m/s的小风层;污染前期640m高度内的各层回流指数廓线小于0.6,100m高度小于0.4,污染缓解后回流指数高于0.7.（2）地面PM_2.5浓度与逆温强度的相关系数为0.42,过程平均逆温厚度167m,平均逆温强度为1.08℃/100m;（3）PM_2.5浓度与边界层高度的相关系数为-0.56,清洁时段的平均边界层高度（876m）约为污染时段（620m）的1.4倍,过程最低边界层高度为267m;PM_2.5浓度与边界层通风量的相关系数为-0.61,清洁时段的平均边界层通风量（2538m²/s）约为污染时段（1136m²/s）的2.2倍,使用边界层通风量能更好表征大气污染的程度.     

基质冲击对ANAMMOX颗粒释放AHLs及颗粒特性的影响

从群体感应角度考察基质冲击对ANAMMOX颗粒特性的影响,以期为提高ANAMMOX颗粒抗基质冲击能力提供理论指导与借鉴.结果表明,24h 1500mg/L总氮冲击刺激颗粒AHLs释放量由4.3大幅增加至10.0,同时颗粒结合性胞外聚合物（B-EPS）过量释放（增加了107.3mg/g VSS）,导致颗粒沉降性能下降（密度和沉速分别降低了53%和33%）.但基质浓度恢复至稳定期水平后,AHLs释放量逐渐恢复至稳定期水平,同时B-EPS产量和颗粒性状也逐渐恢复至稳定期水平,推测基质冲击导致AHLs释放量的变化进而引起B-EPS产量的变化.批次试验结果进一步证实了基质浓度显著影响AHLs释放量,B-EPS产量与AHLs释放量密切相关.总氮浓度为1000mg/L时,AHLs释放量高达11.7,导致B-EPS中的松散结合性EPS（LB-EPS）相比总氮浓度为200mg/L时增加了69mg/g VSS,颗粒沉降性能下降.然而紧密结合性EPS（TB-EPS）含量不受基质浓度影响,认为LB-EPS是决定颗粒沉降能力的关键因素.低浓度抑制剂可有效抑制高基质浓度引起的AHLs过量释放,使LB-EPS产量降低36%,颗粒沉降性能和活性得以提高.     

Development of a model to simulate soil heavy metals lateral migration quantity based on SWAT in Huanjiang watershed, China

Lateral transportation of soil heavy metals in rainfall events could significantly increase the scope of pollution. Therefore, it is necessary to develop a model with high accuracy to simulate the migration quantity of heavy metals. A model for heavy metal migration simulation was developed based on the SWAT(Soil and Water Assessment Tool) model. This model took into consideration the influence of soil p H value, soil particle size, runoff volume, sediment amount,concentration of water-soluble heavy metals dissolved in runoff and insoluble absorbed to the soil particles. This model was reasonable in Huanjiang watershed, Guangxi Zhuang Autonomous Region, south China, covering an area of 273 km~2. The optimal drainage area threshold was determined by analyzing the effects of watershed subdivision on the simulation results to ensure the simulation accuracy. The main conclusions of this paper were:(1) watershed subdivision could affect simulation migration quantity of heavy metals;(2) the quantity of heavy metals transported by sediment accounted for 97%–99% of the total migration quantity in the study watershed. Therefore, sediment played the most important role in heavy metal migration;(3) the optimal drainage area threshold percentage to ensure high simulation accuracy was determined to be 2.01% of the total watershed;(4) with the optimal threshold percentage, this model could simulate the migration quantity of As, Pb and Cd accurately at the total watershed and subwatershed level. The results of this paper were useful for identifying the key regions with heavy metal migration.     

Response of the sediment geochemistry of the Changjiang River (Yangtze River) to the impoundment of the Three Gorges Dam

Based on the measurement of major and trace elements in suspended sediments in the low reaches of the Changjiang River during throughout a whole hydrologic year, the origins, seasonal variations, and fluxes of multielements and the human impacts on multielements transport processes have been analyzed along with the influence of weathering in the Changjiang River basin. The results show that most element contents were high in both autumn and winter and low in summer, which was largely caused by the dilution of discharge. Weathering detritus in the Changjiang River basin is the main source of most elements in suspended sediments. However, riverine pollution could bring more loadings of Cd, Pb, As and Zn into river water than it did a few decades ago. The annual average fluxes of Cd, Pb and Zn, which are major contamination elements, to the sea were 179 ± 21 tons/year, 7810 ± 675 tons/year, and 12,000 ± 1320 tons/year,respectively, in which approximately 8.7%, 11.9% and 2.7% of their loadings, respectively,were contributed by pollution inputs. Element exports mainly occurred in the summer(44.4%–57.4%) in the lower part of the Changjiang River. A general relationship between sediment retention and element content suggests a positive feedback mechanism for the decreased number of particles, in which element riverine loadings are reduced due to the enhanced trapping effect by the Three Gorges Dam(TGD). Compared to those in 1980,current element shares of the Changjiang River compared to the global budget have declined due to the construction of the TGD.     

Enzyme-electrolytic degradation of dichloromethane: Efficiency, kinetics and mechanism

Enzymatic electrolysis cell(EEC) has advantages over microbial electrolysis cell(MEC) due to the needless of microbe inoculation and high-efficiency of enzymatic reaction. In this study, an EEC was first applied to achieve the effective degradation of halogenated organic pollutants and dichloromethane(CH_2Cl_2) was utilized as a model pollutant. The results indicate that the degradation efficiency of CH_2Cl_2 after 2 hr reaction in the EEC was almost100%, which was significantly higher than that with enzyme(51.1%) or current(19.0%). The current induced the continuous regeneration of reduced glutathione(GSH), thus CH_2Cl_2 was degraded under the catalysis of GSH-dependent dehalogenase through stepwise dechlorination, and successively formed monochloromethane(CH_3Cl) and methane(CH_4). The kinetic result shows that with a current of 15 mA, the maximum specific degradation rate of CH_2Cl_2(3.77 × 10~(-3) hr~(-1)) was increased by 5.7 times. The optimum condition for CH_2Cl_2 dechlorination was also obtained with pH, current and temperature of 7.0, 15 mA and 35°C,respectively. Importantly, this study helps to understand the behavior of enzymes and the fate of halogenated organic pollutants with EEC, providing a possible treatment technology for halogenated organic pollutants.     

电子束物理气相沉积制备热障涂层研究进展

介绍了电子束物理气相沉积设备的主要组成、工作原理和电子束物理气相沉积热障涂层的结构特点,并重点论述了工件转速、工件温度、靶材蒸汽入射角度、工件表面的粗糙度、粘结层预氧化、改性粘结层和双层陶瓷层等对电子束物理气相沉积热障涂层性能的影响。     

废弃硅钼棒循环再利用制备MoSi2 基抗氧化涂层

目的在实现钼资源循环再利用的同时,提高钼合金高温抗氧化性能。方法将废弃硅钼棒破碎、球磨制成粉末,并结合玻璃粉和硅粉作为原料,采用浆料法在钼基体上制备MoSi_2基抗氧化涂层。通过扫描电子显微镜、X射线衍射和1400℃静态等温氧化实验等分析涂层的微观组织、结构及抗氧化性能。结果制备的MoSi_2基抗氧化涂层厚度约500μm,涂层整体上呈现出相对致密的结构。在1400℃氧化20h后,涂层质量增量为5.88 mg/cm2,呈现出较好的防氧化效果。结论利用浆料法,以废弃硅钼棒为原料,在实现钼资源回收再利用的同时,为钼合金表面制备具有较好抗氧化性能的MoSi_2基抗氧化涂层。氧化过程中,涂层在表面形成了一层致密的SiO2玻璃,具有较强的阻氧能力,减少氧气向基体的渗入,可以在高温氧化环境有效提升钼基体的抗氧化能力。     

两种抗生素菌渣经SEA-CBS技术处理后的肥料特性

抗生素菌渣的环境无害化利用处置目前已成为行业和政府管理部门亟待解决的难题.为有效实现抗生素菌渣的资源化利用,开展了经SEA-CBS高效复合资源化利用技术制成的吉他霉素和螺旋霉素菌渣有机肥理化特性研究,并分析了未施肥、施加不同比例的商品肥和菌渣有机肥对苦苣生长的影响.结果表明:吉他霉素和螺旋霉素菌渣有机肥的pH分别为6.59和7.92,含水率分别为5.21%和10.60%,抗生素残留均未检出;吉他霉素菌渣有机肥中w（Cr）、w（Pb）和w（As）相对较高,分别为33.40、7.05和1.57 mg/kg,而w（Cd）（0.34 mg/kg）和w（Hg）（低于0.002 mg/kg）相对较低;两种抗生素菌渣有机肥的总养分含量均在5%以上,w（有机质）均大于80%,均符合NY 884—2012《生物有机肥》及NY 525—2012《有机肥料》中的相关限值.植株生长试验研究发现,施加1%和3%的吉他霉素菌渣有机肥时,苦苣的株高、鲜质量和干质量均优于未施肥处理,且株高均大于施入商品肥处理;施加1%螺旋霉素菌渣有机肥下苦苣生长性能优于未施肥情况.研究显示,SEA-CBS技术可有效去除菌渣中残留的抗生素,并实现抗生素菌渣的资源化利用.