Ethyl thiosemicarbazide intercalated organophilic calcined hydrotalcite as a potential sorbent for the removal of uranium(VI) and thorium(IV) ions from aqueous solutions

This work was conducted to determine the practicability of using a new adsorbent 4-ethyl thiosemicarbazide intercalated,organophilic calcined hydrotalcite(ETSC-OHTC) for the removal of uranium(U(VI)),and thorium(Th(IV)) from water and wastewater.The FTIR analysis helped in realizing the involvement of nitrogen and sulphur atoms of ETSC in binding the metal ions through complex formation.Parameters like adsorbent dosage,solution pH,initial metal ions concentration,contact time and ionic strength,that influence adsorption phenomenon,were studied.The optimum pH for maximum adsorption of U(VI) and Th(IV) was found to be in the range 4.0-6.0.The contact time required for reaching equilibrium was 4 hr.The pseudo second-order kinetic model was the best fit to represent the kinetic data.Analysis of the equilibrium adsorption data using Langmuir,Freundlich and Sips models showed that the Freundlich model was well suited to describe the metal ions adsorption.The K F values were 25.43 and 29.11mg/g for U(VI) and Th(IV),respectively,at 30°C.The adsorbent can be regenerated effectively from U(VI) and Th(IV) loaded ones using 0.01mol/L HCl.The new adsorbent was quite stable for many cycles,without much reduction in its adsorption capacity towards the metals.     

Influence of dissolved organic matter character on mercury incorporation by planktonic organisms：An experimental study using oligotrophic water from Patagonian lakes

Ligands present in dissolved organic matter （DOM） form complexes with inorganic divalent mercury （Hg^2＋） affecting its bioavailability in pelagic food webs. This investigation addresses the influence of a natural gradient of DOM present in Patagonian lakes on the bioaccumulation of Hg^2＋ （the prevailing mercury species in the water column of these lakes） by the algae Cryptomonas erosa and the zooplankters Brachionus calyciflorus and Boeckella antiqua. Hg^2＋ accumulation was studied through laboratory experiments using natural water of four oligotrophic Patagonian lakes amended with^197Hg^2＋. The bioavailability of Hg^2＋ was affected by the concentration and character of DOM. The entrance of Hg^2＋ into pelagic food webs occurs mostly through passive and active accumulation. The incorporation of Hg^2＋ by Cryptomonas, up to 27% of the Hg^2＋ amended, was found to be rapid and dominated by passive adsorption, and was greatest when low molecular weight compounds with protein-like or small phenolic signatures prevailed in the DOM. Conversely, high molecular weight compounds with a humic or fulvic signature kept Hg^2＋ in the dissolved phase, resulting in the lowest Hg^2＋ accumulation in this algae. In Brachionus and Boeckella the direct incorporation of Hg from the aqueous phase was up to 3% of the Hg^2＋ amended. The dietary incorporation of Hg^2＋ by Boeckella exceeded the direct absorption of this metal in natural water, and was remarkably similar to the Hg^2＋ adsorbed in their prey. Overall, DOM concentration and character affected the adsorption of Hg^2＋ by algae through competitive binding, while the incorporation of Hg^2＋ into the zooplankton was dominated by trophic or dietary transfer.     

Shear cutting and counter shear cutting of sandwich materials

New lightweight sandwich materials challenge existing forming processes as well as following process steps. As such the manufacturing potential of shear cutting has to be evaluated. Two cutting methods are compared. Method commonly used is shear-cutting within one stroke engaged, the other one is known as counter-shear cutting, which uses two strokes.The challenges of cutting sandwich materials are variation of hole diameter within the different layers, fraying of the textiles, deformation of the hole contour and burr formation. These effects occur in conventional shear cutting as the intermediate layer and the lower sheet metal are cut by the scrap of the upper sheet instead of the cutting punch.The following methodology included shear cutting with closed cutting edge i.e. cutting of holes into five different sandwich materials. The sandwiches exemplarily represent multiple kinds of possible material designs. For instance, aluminum and steel face sheets, different thicknesses of intermediate layers and different intermediate layers materials such as integrated textile fibers have been used. Adequate cutting parameters such as die clearance and the use of a blank holder have been determined. To achieve good results a stiff machine design with good guidance and precise control of punch position was crucial.Observations of conventional shear cutting revealed the need of small cutting clearance of 4%. High burnish area is possible for the upper face sheet due to the superimposed force by the lower face sheet. The major conclusion depicted that high cutting quality of sandwich materials requires counter shear cutting. Hence, the roll-over of the lower sheet facing the intermediate layer, the burnish area at the lower sheet, good cutting quality of the fibers improve significantly and burr formation is avoided completely. Summarized this paper provides cutting parameters for sandwich materials based on experimental work.     

Resistance mash welding for joining of copper conductors for electric motors

The automotive industry is developing designs and manufacturing processes for a new generation of electric motors intended for use in hybrid and electric vehicles. This paper is focused on using solid-state welding to join rectangular wires in the fabrication of motor stators. Resistance welding has not typically been applied to copper due to its very high electrical conductivity; however through optimization of the current and pressure profiles, excellent quality copper-to-copper joints have been demonstrated with a technique known as resistance mash welding. A better understanding of resistance mash welding characteristics will help advancements in its application for stators. The limitations of this application will be discussed.     

Application of CGP-cross route process for microstructure refinement and mechanical properties improvement in steel sheets

A modified method of severe plastic deformation (SPD) entitled constrained groove pressing-cross route (CGP-CR) was introduced for imposing a high magnitude of equivalent strain of about 2.32 per pass on the sheet form samples. The major benefit of this improved route compared to previous common route was the more homogeneity of strain in the rolling (RD) and transverse (TD) directions of sheets. In this study, low carbon steel samples were used for examination of evolutions in microstructure and mechanical properties during SPD via CGP-CR process. Mechanical properties improvement were measured by tensile and macro hardness tests. The results indicate that CGP-CR process can effectively improve tensile strength; and also, yield stress and hardness of as-received low carbon steel samples were improved up to about 100% after two deformation passes. Also, high magnitude of inhomogeneity can be observed in hardness distribution through first pass of the process which diminishes in the subsequent passes. Microstructural evolutions during process were monitored by optical microscopy observations and X-ray diffraction analysis. The results demonstrate that initial ferritic microstructure with grain size of about 30 μm was refined to a 225 nm cell structure after two passes of CGP-CR process.     

Dimensional analysis and scaling in mechanical mixing for fabrication of metal matrix nanocomposites

For a successful enhancement of mechanical properties of metal matrix nanocomposites, a homogeneous nanoparticle dispersion and distribution in the solidified metal is required. Mechanical mixing can be used for initial break-up of agglomerates, and its study can be simplified with dimensional analysis. Using this technique, mixing time and vortex height were assessed while varying fluid properties, impeller angle, and angular speed. Three relevant dimensionless numbers were recognized: the Reynolds (Re), Froude and Galilei (Ga) numbers. Based on blade and impeller shaft angles, a modified Froude number (Fr*) was defined. These parameters were calculated experimentally, varying angular speed from 200 to 1000 rpm for three different impeller angles: 0°, 15° and 30°. This procedure was performed with three fluids: water, and two aqueous glycerin solutions (25% and 50% by volume). Digital images were taken and processed to measure vortex height. Mixing time was measured for water at 0° impeller angle, angular speed ranging from 200 to 1200 rpm. Results showed an optimal dimensionless mixing time with respect to Re. A linear relationship was found between dimensionless vortex height and Fr*. The first had a second order polynomial relationship with the product ReFr*, regardless of impeller angle. This relationship, together with the Ga, specific for each fluid, allows scaling the results to other fluids such as molten pure aluminum. This study allows experimenting in simpler systems that involve transparent fluids, room temperature and low cost, to then elaborate a prediction of vortex height in fluids where measurements are difficult and costly, such as molten metals.     

Analysis of machined surface quality in a single-pass of ball-end milling on Inconel 718

The ball-end milling process is widely used for generating three-dimensional sculptured surfaces with definite curvature. In such cases, variation of surface properties along the machined surface curvatures is not well understood. Therefore, this paper reports the effect of machining parameters on the quality of surface obtained in a single-pass of a ball-end milling cutter with varying chip cross-sectional area. This situation is analogous to generation of free form cavities, pockets, and round fillets on mould surfaces. The machined surfaces show formation of distinct bands as a function of instantaneous machining parameters along the periphery of cutting tool edge, chip compression and instantaneous shear angle. A distinct variation is also observed in the measured values of surface roughness and micro-hardness in these regions. The maximum surface roughness is observed near the tool tip region on the machined surface. The minimum surface roughness is obtained in the stable cutting zone and it increases towards the periphery of the cutter. Similar segmentation was observed on the deformed chips, which could be correlated with the width of bands on the machined surfaces. The sub-surface quality analysis in terms of micro-hardness helped define machining affected zone (MAZ). The parametric effects on the machining induced shear and residual stresses have also been evaluated.     

Incorporating stakeholder decision support needs into an integrated regional Earth system model

A new modeling effort exploring the opportunities, constraints, and interactions between mitigation and adaptation at regional scale is utilizing stakeholder engagement in an innovative approach to guide model development and demonstration, including uncertainty characterization, to effectively inform regional decision making. This project, the integrated Regional Earth System Model (iRESM), employs structured stakeholder interactions and literature reviews to identify the most relevant adaptation and mitigation alternatives and decision criteria for each regional application of the framework. The information is used to identify important model capabilities and to provide a focus for numerical experiments. This paper presents the stakeholder research results from the first iRESM pilot region. The pilot region includes the Great Lakes Basin in the Midwest portion of the United States as well as other contiguous states. This geographic area (14 states in total) permits cohesive modeling of hydrologic systems while also providing strong gradients in climate, demography, land cover/land use, and energy supply and demand. The results from the stakeholder research indicate that, for this region, iRESM should prioritize addressing adaptation alternatives in the water resources, urban infrastructure, and agriculture sectors, including water conservation, expanded water quality monitoring, altered reservoir releases, lowered water intakes, urban infrastructure upgrades, increased electric power reserves in urban areas, and land use management/crop selection changes. For mitigation in this region, the stakeholder research implies that iRESM should focus on policies affecting the penetration of renewable energy technologies, and the costs and effectiveness of energy efficiency, bioenergy production, wind energy, and carbon capture and sequestration.