大气沉降向华中丘陵区稻田输入硫通量的观测

选取我国华中丘陵区的湖南省长沙县一个典型水稻种植区,对2015与2016年2年雨水样中的SO₄²-S和大气SO₂的沉降量进行监测,分析雨水中SO₄^2-、NO₃^-的关系,解析大气硫沉降的主要来源.结果表明,研究区大气中SO₂-S和雨水中SO₄^2--S的年均浓度分别为8.5 μg/m³和1.1mg/L,大气硫沉降年均总量为26.8kgS/（hm²·a）,其中年均降雨混合沉降量18.2kgS/（hm²·a）,年均干沉降量为8.6kgS/（hm²·a）.研究区域硫素干、混合沉降量存在明显的季节差异,硫素混合沉降春季高于夏、秋、冬季,而硫素干沉降冬季高于春、夏、秋季.雨水中NO₃^-/SO₄^2-的质量比大多小于1,表明研究区大气硫素主要来自固定污染源（燃煤）.华中丘陵区稻田具有较高的硫沉降,但硫沉降量已较21世纪初出现了较大幅度下降,农业生产中需要根据农田硫素收支状况酌情补充硫肥来保证作物高产稳产.     

华北地区沙尘天气垂直气溶胶直接辐射强迫

利用CALIOP数据和SBDART（Santa Barbara DISORT Atmospheric Radiative Transfer）辐射传输模式研究了2013~2016年华北地区8d沙尘天气气溶胶及其直接辐射强迫垂直分布特征,分析了气溶胶垂直分布和光学特性对直接辐射强迫的影响.结果表明,气溶胶集中分布在地表及以上3km范围,其中纯净沙尘型和污染沙尘型气溶胶位于上层,污染大陆型气溶胶和烟雾位于下层.大气层顶、地表和大气层的日均气溶胶直接辐射强迫分别是-38.41~-88.44,-74.03~-225.86,9.06~137.42W/m².0~8km高度范围气溶胶直接辐射强迫是负值,且随着高度的增加绝对值逐渐减小.气溶胶垂直分布对大气层顶、地表和大气层的直接辐射强迫影响较小,但对直接辐射强迫垂直分布影响较大,由气溶胶廓线差异造成的同一高度层气溶胶直接辐射强迫最大差值能达到31.18W/m².气溶胶光学厚度和单次散射反照率对直接辐射强迫影响明显.消光能力相同时,吸收性气溶胶对短波太阳光的衰减作用大于散射性气溶胶,后向散射比例大的气溶胶大于后向散射比例小的气溶胶.     

氮掺杂二氧化钛负载钒磷氧催化氧化NO的实验研究

以VPO为活性组分,N掺杂TiO 2为载体,采用浸渍法制备了VPO/TiN催化剂,基于单因素实验研究了其对NO的选择性催化氧化(SCO)性能以及抗硫抗水性能。研究表明:当P/V为1/5、N/Ti为1、活性组分负载量为10%、焙烧温度为350℃时,催化剂的SCO活性最好,NO氧化率达到61%;光致发光光谱(PL)表征显示N掺杂TiO 2在催化剂表面形成的氧空位可增强催化剂对O 2的吸附;VPO/TiN催化剂抗硫抗水性能较强,反应后的催化剂表面未发现硫酸根的特征峰,水蒸气主要通过与NO竞争吸附占据活性位点来抑制催化剂的SCO活性。     

Heterogeneity in the relationship between carbon emission performance and urbanization: evidence from China

Mitigation and Adaptation Strategies for Global Change - Global change caused by carbon emissions alone has become a common challenge for all countries. However, current debates about urbanization...     

双区静电除尘器的数值模拟研究

采用数模拟的方法研究了双区静电除尘器内流场分布、颗粒荷电及颗粒运动等难以直接测量的物理过程,构建了双区静电除尘过程完整的数值模型.采用泊松方程、电流连续性方程和匀强电场方程描述电场,采用N-S方程和雷诺应力标准湍流模型描述流场,采用拉格朗日法描述颗粒运动轨迹.通过截面风速与颗粒去除率的模拟值与实验值的对比,验证了数值模型在模拟内部流场和颗粒运动时的准确性.数值模拟结果表明：双区静电除尘器内部流场分布对入口风速的变化非常敏感;颗粒荷电方式占比由颗粒粒径决定;荷电区内颗粒向极板的趋近过程由流体曳力和电场力共同完成,收尘区内的趋近过程则由电场力主导;入口流速通过改变颗粒前进速度和内部流场形态来影响颗粒运动轨迹.     

Nanoencapsulation of hexavalent chromium with nanoscale zero-valent iron: High resolution chemical mapping of the passivation layer

Solid phase reactions of Cr(Ⅵ) with Fe(0) were investigated with spherical-aberration-corrected scanning transmission electron microscopy(Cs-STEM) integrated with X-ray energy-dispersive spectroscopy(XEDS). Near-atomic resolution elemental mappings of Cr(Ⅵ)–Fe(0) reactions were acquired. Experimental results show that rate and extent of Cr(Ⅵ) encapsulation are strongly dependent on the initial concentration of Cr(Ⅵ) in solution. Low Cr loading in nZⅥ(1.0 wt%) promotes the electrochemical oxidation and continuous corrosion of n ZⅥ while high Cr loading(1.0 wt%) can quickly shut down the Cr uptake. With the progress of iron oxidation and dissolution, elements of Cr and O counter-diffuse into the nanoparticles and accumulate in the core region at low levels of Cr(Ⅵ)(e.g., 10 mg/L). Whereas the reacted n ZⅥ is quickly coated with a newly-formed layer of 2–4 nm in the presence of concentrated Cr(Ⅵ)(e.g., 100 mg/L). The passivation structure is stable over a wide range of pH unless pH is low enough to dissolve the passivation layer. X-ray photoelectron spectroscopy(XPS) depth profiling reconfirms that the composition of the newly-formed surface layer consists of Fe(Ⅲ)–Cr(Ⅲ)(oxy)hydroxides with Cr(Ⅵ) adsorbed on the outside surface. The insoluble and insulating Fe(Ⅲ)–Cr(Ⅲ)(oxy)hydroxide layer can completely cover the n ZⅥ surface above the critical Cr loading and shield the electron transfer. Thus, the fast passivation of nZⅥ in high Cr(Ⅵ) solution is detrimental to the performance of nZⅥ for Cr(Ⅵ) treatment and remediation.     

Relationship between physicochemical properties and dewaterability of hydrothermal sludge derived from different source

Sewage sludge (SS) and deinking sludge (DS) were used to comparatively study the hydrothermal dewatering of sludge with different components. For a better overview, an insight into the relationship between physicochemical properties and dewaterability of hydrothermal sludge was provided. Results found that not all kinds of sludge were suitably conditioned by hydrothermal treatment (HT) in term of the elevation of dewaterability. Higher hydrothermal temperature tended to enhance the dewaterability of SS rather than DS, which was supported by the variation of their physicochemical properties (including water distribution, bonding energy, extracellular polymeric substance (EPS), particles size, acid functional groups and zeta potential in this study). In addition, the changes in surface morphology suggested that the reverse effect of HT on sludge dewaterability was mainly due to their dewatering behavior. For SS, the destruction of EPS structure leaded to the release of bound water, thereby strengthening sludge dewatering. Conversely, “Bridging effect” generated by lignocellulose in DS was beneficial for sludge dewatering; however, the increasing hydrothermal temperature degraded part of lignocellulose and weakened “bridging effect”, finally resulting in worse dewaterability of DS.     

7B04铝合金和30CrMnSiA钢短期腐蚀的电化学行为研究

目的研究7B04铝合金和30CrMnSiA合金钢试样的电化学性能。方法采用电化学实验、扫描电子显微镜(SEM)、腐蚀坑深度测试分别对7B04铝合金和30CrMnSiA合金钢试样在是否经过天然海水浸泡的情况下进行测试分析,得到微观腐蚀形貌和腐蚀坑深度以及试样表面不带锈和带锈时的电化学性能。结果随着Na Cl浓度增大,7B04铝合金和30CrMnSiA钢的自腐蚀电流变大,两者之间存在明显的电位差,接触后会发生电偶腐蚀。电偶电流与阴阳极面积比和Na Cl浓度有关,阴阳极面积比增大或Na Cl浓度升高均会导致电偶效应增强。经过海水短期浸泡后,7B04铝合金表面的锈层不仅没有起到抑制腐蚀的作用,反而使自腐蚀加重,但电偶效应确实有所减弱。结论沿海设备在使用过程中应竭力避免铝合金在锈层下工作。     

飞机用铝合金腐蚀行为和腐蚀预测研究现状及问题分析

针对不同的航空铝合金结构及部位,从腐蚀机理、腐蚀行为和腐蚀预测技术三方面较为系统地分析了研究现状及进展。在此基础上,明确了航空铝合金腐蚀预测技术需要进一步研究的问题,分别为飞机结构表面腐蚀环境的确定问题,材料在海洋大气环境下腐蚀电化学性能的准确测量问题,腐蚀预测模型的选取问题。