玉米深加工废水的混凝实验

在室温条件下,分别选用聚合氯化铝(PAC)、聚合氯化铝铁(PAFC)及三氯化铁(FeCl3)对玉米深加工废水进行混凝实验。综合考虑各种混凝剂对磷、COD以及SS的去除效果,最终选取PAC作为混凝剂。采用PAC和聚丙烯酰胺(PAM)作为复合混凝剂,对其去除效果做进一步研究,并确定了最佳投加量及pH值。实验结果表明,在PAC投加量25mg/L,PAM投加量0.5 mg/L,pH为8条件下,混凝效果最佳。磷、COD、SS去除率可分别达到90.1%、53.3%和88.2%,对应的出水质量浓度分别为0.41、26.8和2 mg/L。     

林可霉素菌(Streptomyces lincolnensis)利用吡唑酮废水的研究

采用被吡唑酮废液驯化、分离、筛选后的林可霉素菌,并对其在摇瓶上利用吡唑酮废液中的硫酸铵发酵(7 d)生产林可霉素进行了研究。实验结果表明,废液加入培养基体积比都为1∶10,实验1中菌丝代谢和对照比正常,其中还原糖利用最快,在发酵后期为0.24 mg/L,林可霉素起步效价最低为2 100 IU/mL,与对照相比最后发酵效价降低了70 IU/mL;实验2发酵过程pH值偏低,全程为5.86～6.50,氨基氮代谢缓慢为40 mg/100 mL,最后林可霉素效价最低为4 480 IU/mL;实验3中废液在发酵进入48 h中后期的时候补入能促进菌丝体分泌,最后林可霉素为5 180 IU/mL,比对照发酵水平高出8.82%。可见实验3的实验设计有利于林可霉素菌利用吡唑酮废液生产林可霉素,为废物循环利用、变废为宝的可行性作了有意义尝试。     

优势菌种对餐厨垃圾高温好氧消化的促进

为研究优势菌种对餐厨垃圾高温好氧消化(TAD)的促进作用,本研究通过淀粉水解、油脂降解及明胶液化等生化实验,从餐厨垃圾中筛选出若干对其主要成分具有显著降解效果的优势菌种。通过对样品水溶性TOC(TOCw)、水溶性凯氏氮(KNw)、水溶性C/N(KNw)、pH以及含水率等指标的分析,考察优势菌种对餐厨TAD的促进作用。研究表明,优势菌种制剂最优添加量为1%。在此剂量下,好氧消化60 h,TOCw由8.53%降低为2.49%,C/Nw由18.71降低至6.14,以上指标说明加入优势菌种可加速TAD反应。添加量1%样本的水溶性凯氏氮和pH在反应48 h后开始回升,而未添加生物制剂的样本相关参数回升时间需96 h以上,由此推断优势菌种对TAD的促进机制是加快了蛋白质等大分子有机物的降解速度。     

模拟阳光下Ag／I-TiO2光催化预处理山核桃加工废水

研究了在模拟太阳光下,采用银修饰的碘掺杂二氧化钛光催化剂（Ag／I—TiO2）对某食品厂山核桃加工废水进行光催化预处理的效果。结合x射线衍射（XRD）、比表面积分析（BET）、紫外-可见漫反射光谱（uV—Vis）的表征结果,来分析催化剂结构对于废水处理效果的影响。探讨了Ag含量、废水初始pH（pHi）和光照时间等因素对化学需氧量（COD）去除及水质可生化性（B／C）提高的影响。并得出适宜的反应参数为：3％Ag含量;pHi为6;光照时间为240min。在最佳条件下,COD去除率45％,废水B／C比由0．17上升到0．31。光催化氧化法能够有效降低山核桃加工废水的COD含量,并达到显著提高废水可生化性的目的。     

A/O+MBR工艺处理玉米深加工废水的中试研究

实验基于企业污水站的改造工程,研究了MBR对玉米深加工废水的处理效果并对工艺运行参数优化提出建议.结果表明,该工艺对COD的去除率可以达到90％以上,出水稳定在26 mg/L左右;出水NH4-N达到1 mg/L以下;TN去除率达到70％以上,出水TN达到10 mg/L以下,出水完全达到排放标准.通过4种工况的比较,说明在污泥浓度8 g/L左右,曝气池内DO在3 mg/L左右,MBR内DO＞4 mg/L,好氧段停留时间13.5 h,并保证3h以上的缺氧段水力停留段时间的条件下,A/O+ MBR工艺可以有效去除玉米深加工废水中的污染物.     

电吸附对水中盐类、氨氮、COD的去除效果分析

电吸附技术作为高效、环境友好型的除盐、除氨氮技术,可应用与水的深度处理领域内。为了使污水回用达到工业用水的水质标准,对电吸附去除水中盐类、氨氮、COD的效果进行分析,结果表明,电吸附设备处理不同氨氮浓度的废水,对中低浓度的氨氮去除效果稳定,当进水氨氮浓度低于20 mg/L时,处理后出水氨氮浓度低于5 mg/L,COD浓度小于25 mg/L,达到回用标准;随着进水盐浓度的增大电吸附处理效果逐渐变差,在电导率低于2 500 μS/cm时除盐率在75%左右,氨氮去除率达到70%左右,COD去除率达到60%左右。经电吸附处理后的低氨氮浓度废水,TDS、氨氮浓度均可达到工业回用水标准。     

改性SiO2气凝胶对废水中Fe3+的吸附性能

制备了改性SiO₂气凝胶,考察了经不同类型、不同配比的改性剂改性的SiO₂气凝胶对模拟含Fe³⁺废水的吸附处理效果。实验结果表明：改性SiO₂气凝胶的最佳制备条件为三甲基氯硅烷（TMCS）作改性剂,V（TMCS）#x02236;V（正己烷）=1#x02236;5;当改性SiO₂气凝胶加入量为75g/L、吸附时间为4h、Fe³⁺质量浓度为10mg/L时,模拟含Fe³⁺废水的Fe³⁺去除率为98.32%,剩余Fe³⁺质量浓度为0.168mg/L;采用改性SiO₂气凝胶动态吸附处理流量为420mL/h、Fe³⁺质量浓度为100mg/L的模拟含Fe³⁺废水,吸附后废水中剩余Fe³⁺质量浓度仅为0.196mg/L。     

用Ti/SnO2-RuO2电极处理黑索金废水

利用刷涂法制备了Ti/SnO2-RuO2电极,并通过SEM、XRD等测试手段对其进行形貌及结构表征。利用该电极为阳极处理黑索金(RDX)废水,考察了电解质种类、电解质质量浓度、废水pH、电流密度以及电解时间等对RDX电催化氧化效果的影响。实验结果表明,当处理100 mL质量浓度为50 mg/L的RDX废水时,以Na2SO4为电解质、Na2SO4质量浓度为5.0 g/L、废水pH为7、电流密度为15 mA/cm2、电解时间为300 min的条件下,RDX去除率达到82.55%,COD去除率达到55.41%。     

An overview on the processes and technologies for recycling cathodic active materials from spent lithium-ion batteries

This paper aims to make an overview on the current status and new tendency for recycling cathodic active materials from spent lithium-ion batteries. Firstly, it introduces several kinds of pretreatment technologies, followed by the summary of all kinds of single recycling processes mainly focusing on organic acid leaching and synergistic extraction. Then, several examples of typical combined processes and industrial recycling processes are presented in detail. Meanwhile, the advantages, disadvantages and prospect of each single process, combined process, as well as industrial recycling processes, are discussed. Finally, based on a novel acidic organic solvent, the authors briefly introduce an environmental friendly process to directly recycle and resynthesize cathodic active material LiNi_1/3Co_1/3Mn_1/3O₂ from spent lithium-ion batteries. The preliminary experimental results demonstrated the advantages of low reaction temperature, high separation efficiency and organic solvent cycling and preventing secondary pollution to the environment. This process may be used for large-scale recycling of spent lithium-ion batteries after further study.     

Quantitative evaluation of environmental risks of flotation tailings from hydrothermal sulfidation–flotation process

Floatation tailings (FT) are the main by-products of the hydrothermal sulfidation–flotation process. FT (FT₁ and FT₂) were obtained by treating two different neutralization sludges (NS) (NS₁ and NS₂). This paper quantitatively evaluated the environmental risks of heavy metals (Zn, Cd, Cu, Pb, and As) in FT versus NS. The total concentration and leaching rates (R ₂) of heavy metals in FT were much lower than those in NS, demonstrating that the hydrothermal sulfidation–flotation process was able to effectively suppress the mobility and leachability of heavy metals. The BCR-three sequence leaching procedure of FT confirmed that all metals were transformed into more stable forms (residue and oxidizable forms) than were found that in NS. The potential ecological risk index indicated that the overall risks caused by heavy metals decreased significantly from 6627.59 and 7229.67 (very serious risk) in NS₁ and NS₂, respectively, to 80.26 and 76.27 (low risk) in FT₁ and FT₂, respectively. According to the risk assessment code, none of the heavy metals in FT posed significant risk to the natural environment except Zn (with low risk). In general, the risk of heavy metals in FT had been well controlled.