计算机模拟研究UO2+2在人体细胞液的形态分布

建立了由多种金属离子和小分子配体组成的多相细胞液热力学平衡模型.模拟研究了UO2 2在组织液和细胞液的形态分布及CO2-3、氨三乙酸（NTA）和乙二胺四乙酸（EDTA）浓度对细胞液中UO2 2形态分布的影响.在组织液中,正常生理pH下,当各形态UO2 2总摩尔浓度 [U]= 1.0×10-6 mol/L 或[U]=1.0×10-3 mol/L时,UO2 2均主要以[UO2(CO3)3]4-和[UO2(CO3)2]2-形态存在.在细胞液中,当[U]=1.0×10-6 mol/L时,UO2 2主要以[UO2(CO3)3]4-和[UO2(CO3)2]2-存在;当[U]=1.0×10-3 mol/L,pH为6.0～6.8时,细胞液中存在大量的固相(UO2)3(PO4)2·4H2O,当pH为6.8～7.4时,UO2 2主要以[UO2(CO3)3]4-、[UO2(CO3)2]2-和[(UO2)2CO3(OH)3]-存在.细胞液中(UO2)3(PO4)2·4H2O含量随[U]升高而增加.通过调节细胞液pH和增加细胞液CO2-3浓度均能降低其固相UO2 2配合物含量.在细胞液中增加NTA会增加(UO2)3(PO4)2·4H2O含量,当添加EDTA时会显著降低(UO2)3(PO4)2·4H2O含量.     

亲水性多孔载体在流化床中的生物膜形成过程分析

采用实验制备的一种新型亲水性多孔聚合物作为流化床反应器中生物膜附着生长的载体,实现流态化水力条件下的生物挂膜过程.在3个结构尺寸相同的流化床反应器中考察了接种污泥浓度、进水有机负荷及载体粒径对亲水性多孔载体生物挂膜量的影响,试验结果表明,接种污泥浓度为30 g VSS/L、进水TOC值为350 mg/L、载体粒径为5～8 mm时载体表面的附着生物量最大,反应器运行12 d的载体附着生物量达到4.45 g VSS/L,膜结构稳定,表现出较活性污泥法更高的活性.在进水TOC、氨氮浓度分别为350 ms/L、50 mg/L,HRT为6 h的情况下,两者的去除率分别达到了97.1%和64.3%,表明载体上的生物膜对污水中TOC及氨氮的去除表现出高效率.挂膜后载体表面上的微生物以丝状菌为主,孔壁上的微生物以球菌和杆菌为主要生物相,证明载体内外表面皆适宜微生物的生长,并且形成合理的生物相分布.     

蚯蚓生态滤池处理农村生活污水现场试验研究

对蚯蚓生态滤池处理太湖流域农村生活污水进行现场试验研究.通过对蚯蚓同化容量与污染负荷进行单因素分析,得出蚯蚓生态滤池处理农村生活污水的运行参数与运行方式,并据此进行连续运行试验.结果表明,在表面水力负荷1 m3/(m2*d)、湿干比(布水时间和落干时间之比)1∶3、蚯蚓负荷(以单位体积填料中蚯蚓的质量计)12.5 g/L的条件下,蚯蚓生态滤池处理农村生活污水具有可行性与高效性,单级系统的COD、总氮、氨氮和总磷的去除率分别在81%、66%、82%和89%左右.改进蚯蚓床填料、设计通风结构和采取适宜运行方式,是蚯蚓生态滤池成功应用于农村生活污水处理的三大重要因素.     

液晶显示器液晶处理与铟回收技术

在实验室条件下,对液晶显示器回收的各个重要环节作了初步的探索,提出了一整套回收工艺.其中包括利用丙酮常温浸取去除偏光片、分离玻璃基板、溶解液晶,还包括利用硫酸溶液和二氧化锰联合浸取玻璃基板,铟的浸取率达89%.得到的铟的酸液经过萃取、置换和电解,可以得到铟的产品,为液晶显示器的资源化和无害化提供实验数据和技术支持.     

地震救灾过渡安置点避雷针的布设选点及安装要求

"5.12"汶川8级大地震波及范围很大,给陕西省部分地方造成了不小的损失.灾后,汉中、宝鸡的地震救灾过渡安置点由于缺乏防雷电保护,打雷时有遭受雷电灾害的可能,亟需要对其采取防雷电保护措施.对救灾过渡安置点采用独立避雷针进行防护,该措施安全可靠、简便易行,就成为首选,其布设选点要科学、规范,可使其效益最大化,避雷针的制作和安装应符合技术标准要求,做到牢固可靠,在施工中要因地制宜.综合考虑,始终把安全和牢靠放在首位.     

Modeling in-situ uranium(VI) bioreduction by sulfate-reducing bacteria

We present a travel-time based reactive transport model to simulate an in-situ bioremediation experiment for demonstrating enhanced bioreduction of uranium(VI). The model considers aquatic equilibrium chemistry of uranium and other groundwater constituents, uranium sorption and precipitation, and the microbial reduction of nitrate, sulfate and U(VI). Kinetic sorption/desorption of U(VI) is characterized by mass transfer between stagnant micro-pores and mobile flow zones. The model describes the succession of terminal electron accepting processes and the growth and decay of sulfate-reducing bacteria, concurrent with the enzymatic reduction of aqueous U(VI) species. The effective U(VI) reduction rate and sorption site distributions are determined by fitting the model simulation to an in-situ experiment at Oak Ridge, TN. Results show that (1) the presence of nitrate inhibits U(VI) reduction at the site; (2) the fitted effective rate of in-situ U(VI) reduction is much smaller than the values reported for laboratory experiments; (3) U(VI) sorption/desorption, which affects U(VI) bioavailability at the site, is strongly controlled by kinetics; (4) both pH and bicarbonate concentration significantly influence the sorption/desorption of U(VI), which therefore cannot be characterized by empirical isotherms; and (5) calcium-uranyl-carbonate complexes significantly influence the model performance of U(VI) reduction.     

垃圾填埋场稳定化及其研究现状

文章对直埋场稳定化过程进行了初步描述,并从填埋气、渗滤液、垃圾组成和沉降等４个方面总结了填埋场稳定化的研究现状。     

Effects of Compounded Curing Agents on Properties and Performance of Urea Formaldehyde Resin

The effects of three compounded curing agents on the properties and performance of the urea-formaldehyde (UF) resin were investigated in this study. The compounded curing agents were prepared by mixing ammonium chloride with hexamethylenetetramine, citric acid, and oxalic acid respectively at a ratio of 1:1, named N-H, N–CA, and N–OA, respectively. The curing process, crystallinity, and physical properties were measured, and the three-ply plywood was fabricated to measure its prepress strength, wet shear strength, and formaldehyde emission. Results showed that the compounded curing agents N–CA and N–OA enhanced the initial viscosity, crosslinking density and thermal stability of UF resin. Additionally, the prepress strength of the plywood bonded by UF resin with N–CA and N–OA increased by 82 and 111% respectively compared to the UF resin with NH₄Cl, and the wet shear strength increased by 14 and 16%, the formaldehyde emission decreased by 19 and 42% respectively. However, owing to the short pot-life of these curing agent limited their storage time, the curing agents N–CA and N–OA should be applied to fabricate plywood in winter for obtaining a better bond strength and a lower formaldehyde emission. While the UF resin with N–HT showed a suitable pot-life, so it could be applied to fabricate plywood in summer for long time storage and avoiding procuring problem.     

The key elements analysis of Guangdong & Shenzhen ETS & tips for China national ETS construction

The only joint effort area of provincial and municipal governments resides in Guangdong Province and Shenzhen City in China’s carbon emission trading system (ETS) pilots, which characterize the national carbon ETS plots. The present study on the operating experience from this area has important reference value for the national carbon ETS. Analysis and comparison of the key elements show many differences in coverage, total allowance, allowance allocation, and MRV mechanism between Guangdong and Shenzhen carbon ETS. The present study provides the following explanation: (1) the design characteristics of carbon ETS (e.g. coverage, total quotas, the allocation, and MRV mechanism) depend on the local geographical conditions and policy goals. The differences of economic structure in Guangdong Province and Shenzhen City result in different coverage, which then result in differences in other management elements. (2) The operating state of the carbon market is affected by overall design of carbon ETS: in the case of tighter total allowance, lower proportion of China Certified Emission Reductions, and harsher punishment, the carbon market is relatively active, which intends to produce carbon financial market. Based on deep analysis of operation characteristics of carbon ETS in Guangdong and Shenzhen, the present study suggests that (1) the allowance should be allocated freely at the beginning stage and then gradually transited to the voluntary paid auction; (2) the allowances assigned to companies shall be linked up with their energy-saving objectives; (3) the output fluctuations and economic influence on the allowance allocation should be properly handled to maintain the fairness and consistence of allowance allocation standards; (4) stable public expectation is one of the key elements to maintain the regular operation of carbon ETS; (5) constrained carbon emission behavior outside ETS can contribute to social justice; and (6) the improvement of professional skills of relevant personnel in the enterprise and independent third party can enhance carbon emissions data reliability.