NaCl和KCl对厌氧污泥抑制的动力学研究

在厌氧颗粒污泥和厌氧絮状污泥系统中,进行盐质量浓度(NaCl或KCl质量浓度,下同)对厌氧污泥抑制动力学的研究,得到不同拟合的COD降解动力学方程及参数.实验结果表明:当盐质量浓度为10～30 g/L时,KCl对厌氧污泥的COD比降解速率的抑制程度大于NaCl;当盐质量浓度由0 g/L增至10 g/L时,半速率常数逐渐增加;当盐质量浓度由10 g/L增至30 g/L时,半速率常数逐渐减小;在厌氧污泥系统中,NaCl抑制作用下的盐抑制常数高于KCl,且颗粒污泥的盐抑制常数高于絮状污泥.     

博物馆室内微环境中碱性气体的被动采样方法研究

针对博物馆微环境中的碱性污染气体-氨气,采用自行研制的被动采样器,建立了一套适合博物馆馆藏文物保存环境中氨气含量分析的被动采样-离子色谱检测方法,应用于博物馆的实地采样分析,通过与主动法采样对照,获得了被动采样器在博物馆微环境中氨的吸收系数,从而获得采样点空气中氨气的浓度,为博物馆文物保存环境监测提供了可行方法。     

Behaviour of selected endocrine-disrupting chemicals in three sewage treatment plants of Beijing, China

Occurrence and fate of eight kinds of selected endocrine-disrupting compounds (EDCs) in three sewage treatment plants (STPs) of Beijing, China was investigated. These EDCs, composed of 4-octylphenol (4-OP), 4-n-nonylphenol (4-n-NP), bisphenol A (BPA), estrone (E1), 17α-estradiol (17α-E2), 17β-estradiol (E2), estriol (E3) and 17α-ethinylestradiol (EE2), in every step of STPs, were simultaneously analysed by gas chromatography/mass spectrometry after derivatisation. All the EDCs were detected in the influents of three STPs, and BPA was the most abundant compound. The concentrations of EDCs ranged from 36.6 ng/l of 17α-E2 (STP C) to 1342.3 ng/l of BPA (STP B) in the influent sewages and from below limits of detection of E2 and E3 (STP C) to 142.5 ng/l of E1 (STP B) in the effluent sewages. The STPs could not remove alkylphenols effectively from the aqueous phase with less than 40% reduction. BPA decreased over 90%, and steroid estrogens achieved considerable reductions from 64.8% of E2 to 94.9% of E3. Generally, biological treatment was more effective in removing alkylphenols, BPA and natural estrogens from the aqueous phase than primary treatment. However, the synthetic estrogen, EE2, was mostly removed by the primary treatment with about 63.5% reduction. It is the first time that the concentration of 17α-E2 in the sewage of China was reported in this paper. The compound might have a bearing with the waste effluents of dairy farms around urban area of Beijing.     

基于TM与MODIS遥感数据的农业旱情监测——以河北省为例

以河北省冬小麦种植区域为研究区,基于TM和MOD IS遥感数据,利用植被供水指数法确定了研究区旱情等级。首先,将其与遥感解译获得的冬小麦空间分布图叠加得到受灾冬小麦空间分布图;然后以1 km的距离在受灾冬小麦周围做缓冲区,并与通过人口密度模型获得的人口密度空间分布图叠加,得出受灾人口空间分布;最后基于光能利用率改进模型构建粮食产量回归统计模型,得到粮食产量。目的是从粮食产量和作物受灾影响人口两个方面对农业受干旱影响情况进行遥感监测和定量评价,以期为相关部门制定防灾、抗灾措施提供科学依据。结果表明,2004年研究区:(1)春季受灾面积小,仅占16.4%;(2)旱情较轻,以轻旱为主,占受灾面积的89%;(3)冬小麦种植面积约为23 965.0 km2,受灾面积约606.3 km2,主要位于唐山市和保定市;(4)粮食产量回归统计模型精度达到了87%,冬小麦产量约为11939247 t,单产约为498.8 t/km2。     

A novel approach to rapid detection of acute water toxicity and its policy implications for grassroots sustainable environmental monitoring

Unknown chemicals, emerging contaminants, and the resulting reactions among them make early detection and warning of acute water toxicity extremely challenging. The conventional approach using small fish for toxicity monitoring normally requires a designated species of fish and over a week's time to complete, including dilution of the wastewater, a pre-test, and a full test. It often increases chances for error and delays emergency management. This paper reports a novel approach, based on grassroots knowledge and field and lab experience in Jilin, China. This approach uses a combination of different species of aquarium fish to achieve fast and reliable monitoring. It tests the original source water directly without going through the dilution procedure, while paying attention to the time factor. The approach does not require a pre-test and may shorten the time needed for detecting acute toxicity to a few minutes, using a new classification of aquatic toxicity levels. It is inexpensive to use and may be easily adopted by grassroots organizations. The approach is "greener" and more financially and socially sustainable than traditional approaches. The wide use of the approach has the potential to encourage policy innovations for making toxicity monitoring grassroots based and more effective in reducing acute contamination emergencies.     

Simulation of soil loss processes based on rainfall runoff and the time factor of governance in the Jialing River Watershed,China

Jialing River is the largest tributary in the catchment area of Three Gorges Reservoir, and it is also one of the important areas of sediment yield in the upper reaches of the Yangtze River. In recent years, significant changes of water and sediment characteristics have taken place. The "Long Control" Project implemented since 1989 had greatly changed the surface appearance of the Jialing River Watershed (JRW), and it had made the environments of the watershed sediment yield and sediment transport change significantly. In this research, the Revised Universal Soil Loss Equation was selected and used to predict the annual average amount of soil erosion for the special water and sediment environments in the JRW after the implementation of the "Long Control" Project, and then the rainfall–runoff modulus and the time factor of governance were both considered as dynamic factors, the dynamic sediment transport model was built for soil erosion monitoring and forecasting based on the average sediment yield model. According to the dynamic model, the spatial and temporal distribution of soil erosion amount and sediment transport amount of the JRW from 1990 to 2007 was simulated using geographic information system (GIS) technology and space-grid algorithm. Simulation results showed that the average relative error of sediment transport was less than 10% except for the extreme hydrological year. The relationship between water and sediment from 1990 to 2007 showed that sediment interception effects of the soil and water conservation projects were obvious: the annual average sediment discharge reduced from 145.3 to 35 million tons, the decrement of sediment amount was about 111 million tons, and decreasing amplitude was 76%; the sediment concentration was also decreased from 2.01 to 0.578 kg/m³. These data are of great significance for the prediction and estimation of the future changing trends of sediment storage in the Three Gorges Reservoir and the particulate non-point source pollution load carried by sediment transport from watershed surface.     

Comparison on surface properties and desulfurization of MnO2 and pyrolusite blended activated carbon by steam activation

In this study, MnO₂ and pyrolusite were used as the catalysts to prepare modified activated carbon, that is, AC-Mn and AC-P, respectively, from coals by blending method and steam activation. The Brunauer–Emmett–Teller (BET) results indicated that the AC-P had higher surface areas and micropore volumes than the AC-Mn with the same blending ratio. The relative contents of basic functional groups (i.e., C = O, π-π*) on AC-P were slightly lower than those on AC-Mn, while both contained the same main metal species, namely, MnO. The desulfurization results showed that with 3 wt% of blending ratio, AC-Mn3 and AC-P3 had higher sulfur capacities at 220 and 205 mg/g, respectively, which were much higher than for the blank one (149.6 mg/g). Moreover, the AC-P had relatively higher sulfur capacity than the AC-Mn with the same contents of Mn, which might be attributed to the existence of other metals in pyrolusite. After the desulfurization process, MnO were gradually transferred into MnSO₄, and the relative contents of basic functional groups decreased evidently for both AC-Mn3 and AC-P3. The results demonstrated that pyrolusite could be one good alternative to MnO₂ to prepare modified activated carbon for desulfurization.

Implications: MnO₂ and pyrolusite were used as the additives to prepare modified activated carbon from coals by a blending method and by steam activation, that is, AC-Mn and AC-P, respectively. The AC-P had higher surface areas and micropore volumes than the AC-Mn with the same blending ratio. The AC-Mn and AC-P had higher sulfur capacities than a blank one. Moreover, the AC-P had relatively higher sulfur capacity than the AC-Mn with the same contents of Mn. The results demonstrated that pyrolusite could be one good alternative to MnO₂ to prepare modified activated carbon for desulfurizatio.     

Distribution of polybrominated diphenyl ethers in breast milk,cord blood and placentas: a systematic review

Polybrominated diphenyl ethers (PBDEs) have been extensively used as flame retardants in consumer products. PBDEs rapidly bioaccumulate in the environment, food, wild animals and humans. In this review, we investigated the harmful effects of PBDEs on humans, especially in early life, and summarised the levels of PBDEs in human biological samples (breast milk, cord blood and placentas). In addition, we described the spatiotemporal distribution of PBDEs in this review. PBDE levels in breast milk, cord blood and placentas were generally higher in North America than in other regions, such as Asia, Europe, Oceania and Africa. However, high levels of PBDEs in human biological samples were detected at e-waste recycling sites in South China, East China and South Korea. This finding suggests that newborns living in e-waste regions are exposed to high levels of PBDEs during prenatal and postnatal periods. The time trends of PBDE concentration differed according to the region. Few studies have investigated PBDE levels in humans from 1967 to 2000, but they increased rapidly after 2000. PBDE concentration peaked at approximately 2006 globally. Compared with other PBDE congeners, BDE-47, BDE-153 and BDE-209 were the major components, but the detection rate of BDE-209 was lower than those of others. Future studies should focus on determining the BDE-209 concentration, which requires the implementation of different analytical approaches. Additionally, the levels of PBDEs in human samples and the environment should be monitored, especially in e-waste recycling regions.

Open image in new window

Graphical abstract The figures described the spatial distribution of the lowest (Fig. a1) and highest concentration of ∑PBDE (Fig. a2) in different countries by 2006 and described the spatial distribution of the lowest (Fig. b1) and highest concentration of ∑PBDE (Fig. b2) in different countries from 2007 to 2015. All the figures indicated that the levels of PBDEs in North America were substantially higher than those in many regions of Europe, Asia, Oceania, or Africa. Comparing Fig. a1–b1 or Fig. a2–b2, increasing trends were observed in some countries, especially in some regions in China, Korea and Canada.

     

南京大气细粒子中重金属污染特征及来源解析

利用2011年1月、4月、7月和10月在南京市区和北郊采集的气溶胶样品,研究了南京大气细粒子中zn、Ph、Hg、As和cd5种重金属的污染水平,通过元素相关性分析和因子分析方法,对细粒子中这些重金属的污染来源进行了初步解析。结果表明,南京大气细粒子及其重金属污染严重,北郊普遍比市区严重;As严重超标,cd在南京北郊超标约5倍,zn在市区与北郊的质量浓度均高于其他重金属元素。每种重金属的浓度均随季节而变化。市区细粒子中,As和zn可能主要与燃煤、轮胎灰尘和建筑扬尘等有关,Pb、Hg和cd主要来自交通尘、城市垃圾焚烧等。北郊细粒子中,As、Hg和zn主要来源于燃煤、钢铁冶炼等工业,Pb和cd主要与农作物秸秆燃烧、汽车尾气、道路扬尘等影响有关。     

臭氧氧化法处理焦化废水生化出水的反应动力学简

对臭氧氧化去除焦化废水生化出水COD的反应动力学及其影响因素进行了实验研究,结果表明,在臭氧投加量为8.50 mg/min,反应温度为20℃和初始pH为10.61条件下,对COD的降解符合表观一级反应动力学模型,其相关系数R²=0.9991,表观反应速率常数k_Abs=1.01×10^-3 s^-1。该条件下,臭氧氧化对COD的降解主要来源于高活性羟基自由基的强氧化作用。在不同的臭氧投加量（4.25~12.75 mg/min）、不同的反应温度（10~40℃）和不同的初始pH（3.76~12.53）下,COD的降解也同样遵循一级反应动力学规律。随着臭氧投加量的增大,COD降解的表观反应速率常数从（0.554×10^-3） s^-1增加到（1.06×10^-3） s^-1;随着反应温度的升高,表观反应速率常数从（0.427×10^-3） s^-1增加到（1.40×10^-3） s^-1,温度越高反应速率提高的幅度却越小;在初始pH3.76~10.61范围内,表观反应速率常数从（0.218×10^-3） s^-1增加到（1.01×10^-3） s^-1,在初始pH为12.53时表观反应速率常数下降到（0.857×10^-3） s^-1。